In this circuit, the meter CPU receives engine coolant temperature signals from the ECM. The meter CPU displays engine coolant temperature that is calculated based on the data received from the ECM.
If there is an open or short in the engine coolant temperature sensor circuit, the ECM stores the DTCs. Troubleshoot the SFI System*1 or ECD System*2.
*1: for Gasoline Engine
*2: for Diesel Engine
for 1GR-FE: See page
Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
for 2TR-FE: See page
Click hereEngine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
for 1KD-FTV: See page
Click hereEngine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
for 1GD-FTV w/ Urea SCR System: See page
for 5L-E: See page
Click hereEngine / Hybrid System>5L-E (ENGINE CONTROL)>ECD SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Check the engine type.
| Result | Proceed to |
|---|---|
| except 5L-E | A |
| for 5L-E | B |
A
B
Check if a CAN communication DTC is output.
for LHD with Entry and Start System (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System)>DIAGNOSIS SYSTEM).
for LHD without Entry and Start System (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD without Entry and Start System)>DIAGNOSIS SYSTEM).
for RHD with Entry and Start System (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System)>DIAGNOSIS SYSTEM).
for RHD without Entry and Start System (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD without Entry and Start System)>DIAGNOSIS SYSTEM).
| Result | Proceed to |
|---|---|
| CAN communication DTC is not output. | A |
| CAN communication DTC is output. (for LHD with Entry and Start System) | B |
| CAN communication DTC is output. (for LHD without Entry and Start System) | C |
| CAN communication DTC is output. (for RHD with Entry and Start System) | D |
| CAN communication DTC is output. (for RHD without Entry and Start System) | E |
A
B
C
D
E
Using the GTS, perform the Active Test (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Water Temperature Meter Operation | Engine coolant temperature receiver gauge | OFF, 45, 60, 70, 80, Middle, 110, 120, 127 | - |
Engine coolant temperature receiver gauge indication is normal.
OK
NG
Using the GTS, read the Data List (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Coolant Temperature | Engine coolant temperature/Min.: 0°C (0°F), Max.: 127.5°C (261.5°F) | 75 to 100°C (167 to 212°F): After warming up the engine | - |
Coolant temperature displayed on the GTS is between 75°C (167°F) and 100°C (212°F) after warming up.
OK
NG
Using the GTS, read the Data List (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Coolant Temp | Engine coolant temperature/Min.: -40°C (-40°F), Max: 215°C (419°F) | 75 to 100°C (167 to 212°F): After warming up the engine | - |
Engine coolant temperature value displayed on the GTS is almost the same as actual engine coolant temperature.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for 1GR-FE) | B |
| NG (for 2TR-FE) | C |
| NG (for 1KD-FTV) | D |
| NG (for 1GD-FTV) | E |
A
B
C
D
E
Using the GTS, perform the Active Test (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Water Temperature Meter Operation | Engine coolant temperature receiver gauge | LOW, 60, 70, 80, Normal, 110, 120, HIGH | - |
Engine coolant temperature receiver gauge indication is normal.
OK
NG
Using the GTS, read the Data List (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Coolant Temperature | Engine coolant temperature/Min.: 0°C (0°F), Max.: 127.5°C (261.5°F) | 75 to 100°C (167 to 212°F): After warming up the engine | - |
Coolant temperature displayed on the GTS is between 75°C (167°F) and 100°C (212°F) after warming up.
OK
NG
Using the GTS, read the Data List (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Coolant Temp | Engine coolant temperature/Min.: -40°C (-40°F), Max: 215°C (419°F) | 75 to 100°C (167 to 212°F): After warming up the engine | - |
Engine coolant temperature value displayed on the GTS is almost the same as actual engine coolant temperature.
OK
NG
Disconnect the G6 combination meter assembly connector.
Disconnect the G183 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G6-35 (TEMP) - G183-12 (THWO) | Always | Below 1 Ω |
| G6-35 (TEMP) or G183-12 (THWO) - Body ground | Always | 10 kΩ or higher |
OK
NG
Replace the combination meter assembly (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL).
Check that the operation of the engine coolant temperature receiver gauge returns to normal.
The operation of the engine coolant temperature receiver gauge returns to normal.
OK
NG