Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053736 PRE-CRASH SAFETY _0261101 PRE-CRASH SAFETY SYSTEM U

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  TERMINALS OF ECU  


CHECK SEAT BELT CONTROL ECU


U170573E02
2.823,0.719 3.177,0.865 0.354,0.146 10 false G117 4.521,0.719 4.875,0.865 0.354,0.146 10 false G118

a.

Disconnect the G117 and G118 ECU connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G117-7 (+B) - Body ground W - Body ground Battery Always 11 to 14 V
G117-8 (PGND) - Body ground W-B - Body ground Body ground Always Below 1 Ω
G118-8 (IG1) - Body ground G - Body ground Seat belt control ECU power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the G117 and G118 ECU connectors.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G117-2 (MOR+) - Body ground B - Body ground Seat belt motor RH power supply Ignition switch ON 4.0 to 8.5 V
Ignition switch off Below 1 V
G117-1 (MOR-) - Body ground LG - Body ground Seat belt motor RH power supply Ignition switch ON 4.0 to 8.5 V
Ignition switch off Below 1 V
G117-3 (MOL+) - Body ground R - Body ground Seat belt motor LH power supply Ignition switch ON 4.0 to 8.5 V
Ignition switch off Below 1 V
G117-4 (MOL-) - Body ground G - Body ground Seat belt motor LH power supply Ignition switch ON 4.0 to 8.5 V
Ignition switch off Below 1 V
G118-5 (PBK+) - G118-6 (PBK-) G - R*1
V - P*2
Front seat inner belt (for passenger side) signal Ignition switch ON, front seat belt (for passenger side) fastened Pulse generation
(See waveform 1)
Ignition switch ON, front seat belt (for passenger side) unfastened Pulse generation
(See waveform 2)
G118-6 (PBK-) - Body ground R - Body ground*1
P - Body ground*2
Front seat inner belt (for passenger side) signal Always Below 1 Ω

*1: for LHD

*2: for RHD


If the result is not as specified, the ECU may be malfunctioning.

i.
E198259E01
2.655,1.174 2.981,1.327 0.326,0.152 10 GND

Using an oscilloscope, check waveform 1.

Measurement Condition
Item Content
Tester Connection G118-5 (PBK+) - G118-6 (PBK-)
Tool Setting 2 V/DIV., 20 ms/DIV.
Vehicle Condition Ignition switch ON, front seat belt (for passenger side) fastened


ii.
E198260E01
2.655,1.196 2.985,1.338 0.330,0.142 10 GND

Using an oscilloscope, check waveform 2.

Measurement Condition
Item Content
Tester Connection G118-5 (PBK+) - G118-6 (PBK-)
Tool Setting 2 V/DIV., 20 ms/DIV.
Vehicle Condition Ignition switch ON, front seat belt (for passenger side) unfastened




CHECK DRIVING SUPPORT ECU


U170576E02
3.479,0.281 3.844,0.427 0.365,0.146 10 false G119

NOTICE:
·

As disconnecting the connector to perform inspections may cause DTCs to be stored, clear DTCs after performing inspections.

·

As the connector may be damaged if a load of more than 10 kg (22 lb) is applied it, do not apply any more load than necessary to the connector.



a.

Disconnect the G119 ECU connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G119-30 (B) - Body ground G - Body ground Power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
G119-25 (GND) - Body ground BR - Body ground Body ground Always Below 1 Ω
G119-5 (PBSW) - Body ground V - Body ground Pre-crash brake cancel switch assembly signal Pre-crash brake cancel switch assembly on Below 1 Ω
Pre-crash brake cancel switch assembly off 10 kΩ or higher

If the result is not as specified, there may be a malfunction on the wire harness side.