Wear protective gloves. Sharp areas on the parts may injure your hands.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
79040
1.INSTALL NO. 3 SEAT LEG ASSEMBLY LH
Attach the 4 clips to install the seat cushion under carpet LH to the No. 3 seat leg.
79020B
2.INSTALL NO. 2 SEAT LEG ASSEMBLY (for RH Side)
Attach the 4 clips to install the seat cushion under carpet RH to the No. 2 seat leg.
79304A
3.INSTALL NO. 3 SEATBACK FRAME SUB-ASSEMBLY LH
Using a T45 "TORX" socket wrench, install the seatback frame with the 4 "TORX" bolts.
79226
4.INSTALL NO. 2 SEAT LOCK CABLE
Twist the cable end in the direction indicated by the arrow to connect it.
Attach the clamp to install the cable.
| *1 | Clamp |
| *2 | Cable End |
78091
5.INSTALL FOLD SEAT LOCK CONTROL CABLE SUB-ASSEMBLY
Twist the cable end in the direction indicated by the arrow to connect it.
| *1 | Clamp A |
| *2 | Clamp B |
| *3 | Cable Tie |
| *4 | Cable End |
Attach the 2 clamps labeled A to install the cable.
Install the clamp labeled B together with the No. 2 seat lock cable.
Install 2 new cable ties.
71844A
6.INSTALL REAR NO. 2 SEAT OUTER RECLINING COVER LH
Attach the 2 claws and guide to install the cover.
Install the screw.
71844C
7.INSTALL REAR NO. 2 SEAT INNER RECLINING COVER LH
Attach the 5 claws to install the cover.
71834C
8.INSTALL REAR NO. 3 SEAT OUTER RECLINING COVER LH
Attach the 2 claws and guide to install the cover.
Install the screw.
71834C
9.INSTALL REAR NO. 3 SEAT INNER RECLINING COVER LH
Attach the 4 claws to install the cover.
79962
10.INSTALL NO. 2 SEATBACK COVER
Attach the 2 claws to install the cover.
71587C
11.INSTALL REAR NO. 2 SEATBACK EDGE PROTECTOR
Install the protector to the seatback pad with new tack pins.
79034
12.INSTALL REAR NO. 3 SEATBACK COVER SUB-ASSEMBLY LH
Using hog ring pliers, install the seatback cover to the seatback pad with new hog rings.
| *1 | Hog Ring Pliers |
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
13.INSTALL SEATBACK COVER WITH PAD
Attach the hooks to install the seatback cover with pad.
71931C
14.INSTALL REAR NO. 2 SEAT HEADREST SUPPORT ASSEMBLY
Attach the 4 claws to install the 2 headrest supports.
71702C
15.INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY LH
Attach the 7 clips to install the board.
72690A
16.INSTALL REAR SEAT LOCK RELEASE LEVER ASSEMBLY
Twist the 2 cable ends in the direction indicated by the arrow to connect them.
| *1 | Cable End |
| *2 | No. 2 Seat Lock Cable |
| *3 | Fold Seat Lock Control Cable |
| *2 | Clamp |
Attach the 2 clamps.
Attach the hook.
Install the lever with the 2 screws.
72615G
17.INSTALL REAR NO. 2 SEATBACK LOCK STRIKER COVER
Attach the guide and claw to install the cover.
| *1 | Guide |
66310F
18.INSTALL ROPE HOOK ASSEMBLY
Install the rope hook with the bolt.
Attach the 2 claws to close the cover.
72058B
19.INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH
Twist the cable end in the direction indicated by the arrow to connect it.
| *1 | Clamp |
| *2 | Cable End |
| *3 | Guide |
Attach the clamp.
Attach the guide to install the lever.
Install the 2 screws.
72615H
20.INSTALL REAR NO. 1 SEATBACK LOCK STRIKER COVER
Attach the guide and claw to install the cover.
| *1 | Guide |
72695C
21.INSTALL REAR SEAT LOCK CONTROL CABLE LH
Twist the cable end in the direction indicated by the arrow to connect it.
| *1 | Clamp |
| *2 | Cable End |
Attach the clamp to install the cable.
71694E
22.INSTALL REAR SEAT CUSHION INNER HINGE COVER RH
Attach the guide to install the cover.
Install the clip and screw.
71694E
23.INSTALL REAR SEAT CUSHION INNER HINGE COVER LH
Attach the guide to install the cover.
Install the clip and screw.
79384A
24.INSTALL REAR NO. 3 SEAT LEG COVER LH
Attach the 2 claws to install the cover.
79384
25.INSTALL REAR SEAT LEG COVER LH
Attach the 5 clips and 3 hooks to install the cover.
Install the clip.
72058B
26.INSTALL REAR NO. 2 SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH
Attach the 2 guides.
Install the lever with the screw.
Twist the cable end in the direction indicated by the arrow to connect it.
| *1 | Cable End |
| *2 | Clamp |
Attach the clamp.
72906
27.INSTALL 3RD SEAT LINK SUB-ASSEMBLY LH
Attach the 4 guides and 2 claws to install the link.
Install the 3 clips.
79202
28.INSTALL NO. 2 SEAT CUSHION FRAME SUB-ASSEMBLY LH
Using a T40 "TORX" socket wrench, install the seat cushion frame with the 4 "TORX" bolts.
Pull out the seat cushion frame.
71827B
29.INSTALL REAR NO. 2 SEAT CUSHION MOULDING
Attach the 2 claws to install the moulding.
Install the 2 screws.
71647F
30.INSTALL REAR SEAT CUSHION INNER EDGE PROTECTOR LH
Install the protector to the seat cushion pad with new tack pins.
79032
31.INSTALL NO. 3 SEAT CUSHION COVER SUB-ASSEMBLY LH
Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.
| *1 | Fastener |
| *2 | Hog Ring Pliers |
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
32.INSTALL SEAT CUSHION COVER WITH PAD
Attach the 2 hooks to install the seat cushion cover with pad.
Close the seat cushion cover under part with the 2 clips.
Close the 2 fasteners.
71827B
33.INSTALL REAR NO. 1 SEAT CUSHION MOULDING
Attach the 4 guides and 2 claws to install the moulding.
install the 2 clips.
73590
34.INSTALL REAR NO. 2 SEAT INNER BELT ASSEMBLY LH
71693
35.INSTALL REAR SEAT LOWER CUSHION HINGE COVER RH
Attach the guide and 2 claws to install the cover.
Install the 2 screws.
71693
36.INSTALL REAR SEAT LOWER CUSHION HINGE COVER LH
Attach the 3 claws to install the cover.
Install the 2 screws.
73949
37.INSTALL CAP
Install the 2 caps.
71970
38.INSTALL REAR SEAT HEADREST ASSEMBLY
Install the headrest.