Home › Vehicle Interior › SEAT › POWER SEAT SWITCH(for Rear No. 2 Seat)
RM27T0E _58 Vehicle Interior _053737 SEAT _0261106 POWER SEAT SWITCH(for Rear No. 2 Seat) G

SEAT  POWER SEAT SWITCH(for Rear No. 2 Seat)  INSPECTION  


PROCEDURE

Hide 84923 1.INSPECT REAR POWER SEAT SWITCH (for LH Side)

a.
B239071E01
0.696,0.268 0.859,0.417 0.163,0.149 10 *1 0.696,1.574 0.859,1.723 0.163,0.149 10 *2 1.633,1.858 1.796,2.007 0.163,0.149 10 *a 0.885,1.66 1.418,1.66 false 0.885,0.354 1.418,0.354 false 2.037,3.087 2.394,3.236 0.357,0.149 10 FWD 1.04,3.09 1.439,3.239 0.399,0.149 10 BACK 1.001,1.845 1.122,1.994 0.121,0.149 10 E 1.856,2.689 1.856,3.17 1.856,3.17 2.017,3.17 false 1.696,2.689 1.696,3.17 1.696,3.17 1.535,3.17 false 1.512,2.591 1.26,1.927 1.26,1.927 1.146,1.927 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
4 (FWD) - 6 (E) UP switch pressed Below 1 Ω
5 (BACK) - 6 (E) DOWN switch pressed


If the result is not as specified, replace the rear power seat switch assembly.

Text in Illustration
*1 UP Switch
*2 DOWN Switch
*a Component without harness connected
(Rear Power Seat Switch Assembly)


b.
B239073E01
1.648,1.875 1.797,2.017 0.149,0.142 10 *a 0.848,3.087 1.147,3.238 0.299,0.151 10 ILL+ 2.36,3.087 2.669,3.238 0.309,0.151 10 ILL- 2.223,2.692 2.223,3.173 2.223,3.173 2.343,3.173 false 1.346,2.692 1.346,3.173 1.346,3.173 1.226,3.173 false

Apply battery voltage to the switch connector and check that the power seat switch illuminates.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 7 (ILL+)
Battery negative (-) → 2 (ILL-)
Illumination illuminates


If the result is not as specified, replace the rear power seat switch assembly.

Text in Illustration
*a Component without harness connected
(Rear Power Seat Switch Assembly)


Hide 84923 2.INSPECT REAR POWER SEAT SWITCH (for RH Side)

a.
B239071E01
0.696,0.268 0.859,0.417 0.163,0.149 10 *1 0.696,1.574 0.859,1.723 0.163,0.149 10 *2 1.633,1.858 1.796,2.007 0.163,0.149 10 *a 0.885,1.66 1.418,1.66 false 0.885,0.354 1.418,0.354 false 2.037,3.087 2.394,3.236 0.357,0.149 10 FWD 1.04,3.09 1.439,3.239 0.399,0.149 10 BACK 1.001,1.845 1.122,1.994 0.121,0.149 10 E 1.856,2.689 1.856,3.17 1.856,3.17 2.017,3.17 false 1.696,2.689 1.696,3.17 1.696,3.17 1.535,3.17 false 1.512,2.591 1.26,1.927 1.26,1.927 1.146,1.927 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
4 (FWD) - 6 (E) UP switch pressed Below 1 Ω
5 (BACK) - 6 (E) DOWN switch pressed


If the result is not as specified, replace the rear power seat switch assembly.

Text in Illustration
*1 UP Switch
*2 DOWN Switch
*a Component without harness connected
(Rear Power Seat Switch Assembly)


b.
B239073E01
1.648,1.875 1.797,2.017 0.149,0.142 10 *a 0.848,3.087 1.147,3.238 0.299,0.151 10 ILL+ 2.36,3.087 2.669,3.238 0.309,0.151 10 ILL- 2.223,2.692 2.223,3.173 2.223,3.173 2.343,3.173 false 1.346,2.692 1.346,3.173 1.346,3.173 1.226,3.173 false

Apply battery voltage to the switch connector and check that the power seat switch illuminates.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 7 (ILL+)
Battery negative (-) → 2 (ILL-)
Illumination illuminates


If the result is not as specified, replace the rear power seat switch assembly.

Text in Illustration
*a Component without harness connected
(Rear Power Seat Switch Assembly)


Hide 84190A 3.INSPECT NO. 1 FOLD SEAT SWITCH ASSEMBLY

a.
B239264E01
0.393,0.74 0.549,0.886 0.156,0.145 10 *1 0.393,1.247 0.549,1.393 0.156,0.145 10 *2 2.825,0.745 2.981,0.890 0.156,0.145 10 *3 2.825,1.247 2.981,1.393 0.156,0.145 10 *4 1.635,1.892 1.791,2.037 0.156,0.145 10 *a 1.098,0.822 0.586,0.822 false 1.098,1.325 0.586,1.325 false 2.799,1.325 2.288,1.325 false 2.799,0.822 2.288,0.822 false 2.434,2.047 2.816,2.185 0.382,0.139 10 RTNL 0.677,1.982 1.086,2.121 0.409,0.139 10 RTNR 2.125,3.215 2.496,3.354 0.371,0.139 10 FLDL 0.702,3.215 1.084,3.354 0.382,0.139 10 FLDR 1.484,3.207 1.599,3.352 0.114,0.145 10 E 1.678,2.876 1.549,3.19 false 1.845,2.88 1.949,3.293 1.949,3.293 2.099,3.293 false 1.424,2.88 1.321,3.293 1.321,3.293 1.171,3.293 false 2.03,2.554 2.275,2.124 2.275,2.124 2.413,2.124 false 1.592,2.545 1.343,2.051 1.343,2.051 1.175,2.051 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 (RTNL) - 7 (E) RETURN LH switch pressed Below 1 Ω
6 (FLDL) - 7 (E) FOLD LH switch pressed
3 (RTNR) - 7 (E) RETURN RH switch pressed
8 (FLDR) - 7 (E) FOLD RH switch pressed


If the result is not as specified, replace the No. 1 fold seat switch assembly.

Text in Illustration
*1 RETURN RH Switch
*2 FOLD RH Switch
*3 RETURN LH Switch
*4 FOLD LH Switch
*a Component without harness connected
(No. 1 Fold Seat Switch Assembly)


b.
B239265E01
1.656,1.91 1.805,2.054 0.149,0.144 10 *a 2.312,3.207 2.521,3.356 0.210,0.149 10 +B 1.288,3.196 1.407,3.345 0.119,0.149 10 E 1.678,2.867 1.542,3.282 1.542,3.282 1.433,3.282 false 2.03,2.867 2.166,3.282 2.166,3.282 2.275,3.282 false

Apply battery voltage to the switch connector and check that the fold seat switch illuminates.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 5 (+B)
Battery negative (-) → 7 (E)
Illumination illuminates


If the result is not as specified, replace the No. 1 fold seat switch assembly.

Text in Illustration
*a Component without harness connected
(No. 1 Fold Seat Switch Assembly)