Home › Vehicle Interior › SEAT › REAR POWER SEAT CONTROL SYSTEM
RM27T0E _58 Vehicle Interior _053737 SEAT _0261112 REAR POWER SEAT CONTROL SYSTEM J

SEAT  REAR POWER SEAT CONTROL SYSTEM  Power Source Circuit  


DESCRIPTION

Power is supplied to the fold seat control ECU through the ECU-B, FOLD SEAT LH*1, FOLD SEAT RH*2 and ECU-IG NO. 2 fuses.

*1: for LH Side

*2: for RH Side


WIRING DIAGRAM

B239511E01
0.414,2.699 1.749,2.882 1.334,0.182 10 from IG1 No. 2 Relay 0.916,1.7 1.753,1.870 0.837,0.170 10 from Battery 0.916,0.691 1.753,0.860 0.837,0.170 10 from Battery 2.851,2.888 3.763,3.039 0.912,0.151 10 ECU-IG NO. 2 2.738,1.859 3.907,2.024 1.169,0.165 10 FOLD SEAT LH*1 2.738,2.166 3.916,2.332 1.178,0.165 10 FOLD SEAT RH*2 3.058,0.847 3.519,1.012 0.461,0.165 10 ECU-B 4.713,1.699 4.903,1.852 0.190,0.153 10 c2 5.131,1.699 5.309,1.856 0.177,0.157 10 d2 4.748,1.492 4.843,1.650 0.095,0.157 10 2 5.167,1.492 5.263,1.650 0.096,0.157 10 2 5.495,2.709 5.674,2.870 0.179,0.161 10 IG 5.495,1.699 5.688,1.855 0.194,0.155 10 +B 5.495,0.704 5.911,0.864 0.416,0.160 10 ECUB 5.495,3.646 5.841,3.799 0.346,0.153 10 GND 5.495,4.485 5.917,4.633 0.423,0.148 10 GND2 5.228,5.113 6.709,5.431 1.482,0.318 10 Fold Seat Control ECU LH*1, RH*2 0.259,4.938 1.195,5.103 0.936,0.165 10 *1: for LH Side 0.259,5.304 1.224,5.469 0.964,0.165 10 *2: for RH Side 4.713,1.905 4.866,2.062 0.153,0.157 10 *2 5.144,1.905 5.298,2.063 0.154,0.158 10 *1 4.713,2.709 4.903,2.861 0.190,0.153 10 c1 5.131,2.709 5.309,2.866 0.177,0.157 10 d1 4.749,2.502 4.843,2.659 0.095,0.157 10 3 5.168,2.502 5.264,2.659 0.096,0.157 10 3 4.713,2.915 4.866,3.072 0.153,0.157 10 *2 5.144,2.915 5.299,3.073 0.154,0.158 10 *1 4.713,0.704 4.903,0.857 0.190,0.153 10 c1 5.131,0.704 5.309,0.861 0.177,0.157 10 d1 4.748,0.497 4.843,0.654 0.095,0.157 10 1 5.168,0.497 5.263,0.655 0.096,0.157 10 1 4.713,0.91 4.866,1.067 0.153,0.157 10 *2 5.144,0.91 5.298,1.068 0.154,0.158 10 *1 4.713,3.646 4.903,3.799 0.190,0.153 10 c2 5.131,3.636 5.309,3.794 0.177,0.157 10 d2 4.7,3.439 4.882,3.596 0.183,0.157 10 10 5.126,3.439 5.307,3.596 0.181,0.157 10 10 4.713,3.852 4.866,4.009 0.153,0.157 10 *2 5.144,3.852 5.298,4.010 0.154,0.158 10 *1 4.713,4.485 4.903,4.638 0.190,0.153 10 c2 5.131,4.476 5.309,4.633 0.177,0.157 10 d2 4.748,4.278 4.843,4.436 0.095,0.157 10 9 5.168,4.278 5.264,4.436 0.096,0.157 10 9 4.713,4.691 4.866,4.848 0.153,0.157 10 *2 5.144,4.691 5.298,4.849 0.154,0.158 10 *1

CAUTION / NOTICE / HINT

HINT:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (FOLD SEAT CONTROL ECU - BATTERY AND BODY GROUND)
a.
U115614E01
0.571,0.418 0.745,0.573 0.174,0.155 10 d2 0.576,0.852 0.744,1.006 0.167,0.155 10 c2 0.884,0.273 1.057,0.426 0.173,0.153 10 *A 0.884,0.707 1.057,0.859 0.173,0.153 10 *B 1.212,1.634 1.384,1.788 0.172,0.155 10 d1 2.008,1.637 2.181,1.792 0.173,0.155 10 c1 1.526,1.488 1.699,1.641 0.173,0.153 10 *A 2.315,1.492 2.488,1.645 0.173,0.153 10 *B 1.704,0.083 1.906,0.242 0.202,0.158 10 +B 1.678,1.128 2.097,1.283 0.419,0.155 10 GND2 2.385,0.698 2.730,0.853 0.345,0.155 10 GND 0.327,3.029 0.746,3.184 0.419,0.155 10 ECUB 1.019,3.029 1.197,3.180 0.179,0.152 10 IG 1.666,0.172 1.573,0.172 1.573,0.172 1.503,0.549 false 2.116,0.783 2.355,0.783 false 1.924,0.846 1.924,1.107 false 0.578,2.516 0.578,3.011 false 0.818,2.516 1.103,2.923 1.103,2.923 1.103,3.011 false 0.092,0.077 0.265,0.229 0.173,0.153 10 *a

for LH Side:

Disconnect the d1 and d2 ECU connectors.


b.

for RH Side:

Disconnect the c1 and c2 ECU connectors.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LH Side
Tester Connection Condition Specified Condition
d2-2 (+B) - Body ground Always 11 to 14 V
d1-1 (ECUB) - Body ground Always 11 to 14 V
d1-3 (IG) - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V

for RH Side
Tester Connection Condition Specified Condition
c2-2 (+B) - Body ground Always 11 to 14 V
c1-1 (ECUB) - Body ground Always 11 to 14 V
c1-3 (IG) - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH Side
Tester Connection Condition Specified Condition
d2-10 (GND) - Body ground Always Below 1 Ω
d2-9 (GND2) - Body ground Always Below 1 Ω

for RH Side
Tester Connection Condition Specified Condition
c2-10 (GND) - Body ground Always Below 1 Ω
c2-9 (GND2) - Body ground Always Below 1 Ω



Text in Illustration
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Fold Seat Control ECU)


OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR