Home › Vehicle Interior › SEAT › LUMBAR SWITCH (for Manual Seat)
RM27T0E _58 Vehicle Interior _053737 SEAT _0261121 LUMBAR SWITCH(for Manual Seat) G

SEAT  LUMBAR SWITCH(for Manual Seat)  INSPECTION  


PROCEDURE

Hide 84920 1.INSPECT LUMBAR SWITCH ASSEMBLY (for LHD)

B241815E01
1.611,1.255 1.789,1.447 0.178,0.193 10 *1 2.289,1.255 2.466,1.447 0.178,0.193 10 *2 0.669,1.64 0.847,1.833 0.178,0.193 10 *a 2.286,1.353 2.149,1.353 false 2.488,2.324 2.635,2.487 0.147,0.163 10 R 1.165,2.97 1.307,3.119 0.142,0.149 10 H 0.512,2.324 0.733,2.494 0.222,0.170 10 E1 0.741,2.406 1.198,2.406 false 1.256,2.97 1.411,2.463 false 1.634,2.962 1.634,2.481 false 2.064,2.962 1.894,2.478 false 2.459,2.405 2.081,2.405 false 2.149,1.353 1.738,0.786 false 1.97,2.97 2.220,3.119 0.251,0.149 10 E2 1.577,2.97 1.719,3.119 0.142,0.149 10 B 1.601,1.352 1.464,1.352 false 1.464,1.352 1.276,0.786 false

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
3 (B) - 4 (H) Hold Below 1 Ω
1 (R) - 2 (E2)
1 (R) - 2 (E2) Off
4 (H) - 5 (E1)
1 (R) - 3 (B) Release
4 (H) - 5 (E1)


If the result is not as specified, replace the lumbar switch.

Text in Illustration
*1 Hold Switch
*2 Release Switch
*a Component without harness connected
(Lumbar Switch)


Hide 84920 2.INSPECT LUMBAR SWITCH ASSEMBLY (for RHD)

B241816E01
1.637,1.383 1.815,1.576 0.178,0.193 10 *1 0.957,1.383 1.135,1.576 0.178,0.193 10 *2 0.755,1.786 0.933,1.979 0.178,0.193 10 *a 1.151,1.482 1.288,1.482 false 2.591,2.47 2.738,2.633 0.147,0.163 10 R 1.272,3.099 1.414,3.248 0.142,0.149 10 H 0.615,2.47 0.836,2.640 0.222,0.170 10 E1 0.845,2.553 1.301,2.553 false 1.364,3.099 1.518,2.592 false 1.742,3.091 1.742,2.609 false 2.172,3.091 2.002,2.607 false 2.563,2.551 2.184,2.551 false 1.288,1.482 1.699,0.915 false 2.077,3.099 2.328,3.248 0.251,0.149 10 E2 1.685,3.099 1.827,3.248 0.142,0.149 10 B 1.835,1.481 1.973,1.481 false 1.973,1.481 2.161,0.915 false

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
3 (B) - 4 (H) Hold Below 1 Ω
1 (R) - 2 (E2)
1 (R) - 2 (E2) Off
4 (H) - 5 (E1)
1 (R) - 3 (B) Release
4 (H) - 5 (E1)


If the result is not as specified, replace the lumbar switch.

Text in Illustration
*1 Hold Switch
*2 Release Switch
*a Component without harness connected
(Lumbar Switch)