Wear protective gloves. Sharp areas on the parts may injure your hands.
78910B
1.INSTALL NO. 1 FOLD SEAT LOCK CONTROL CABLE ASSEMBLY RH
Install the cable to the seat cushion frame.
Attach the 3 cable clamps and connect the cable.
Install 2 new cable ties.
71017
2.INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY RH
Install the seatback frame with the 4 bolts.
71834H
3.INSTALL REAR SEAT RECLINING COVER INNER LH
Attach the 2 guides to install the cover.
71878E
4.INSTALL REAR SEAT RECLINING COVER INNER RH
Attach the 2 guides to install the cover.
71879E
5.INSTALL REAR SEAT INNER RECLINING COVER LH
Attach the 2 guides and 2 claws to install the cover.
71878F
6.INSTALL REAR SEAT INNER RECLINING COVER RH
Attach the 2 guides and 2 claws to install the cover.
72620B
7.INSTALL REAR NO. 1 SEAT LOCK CABLE ASSEMBLY
Install the cable to the seatback frame.
Attach the 2 cable clamps and connect the cable.
71077S
8.INSTALL SEPARATE TYPE REAR SEATBACK COVER
Install the seatback cover with 2 new hog rings and attach the fastening tape.
| *1 | Hog Ring Pliers |
| *2 | Fastening Tape |
Using hog ring pliers, install new hog rings.
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
9.INSTALL SEATBACK COVER WITH PAD
Attach the 2 hooks to install the seatback cover with pad.
71931B
10.INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY
Attach the 4 claws to install the 2 supports.
72057
11.INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY RH
Connect the cable in the order shown in the illustration to install the lever.
Install the 2 screws.
72615C
12.INSTALL REAR SEATBACK LOCK STRIKER COVER
Attach the guide and claw to install the cover.
79175
13.INSTALL NO. 1 SEATBACK PAD RH
Install the seatback pad.
Close the 2 fasteners, and then close the seatback cover.
Using hog ring pliers, install 3 new hog rings.
| *1 | Hog Ring Pliers |
Attach the 3 fastening tapes and close the cover.
72996A
14.INSTALL REAR SEATBACK COVER
Attach the 4 claws to install the cover.
71075S
15.INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER
Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.
| *1 | Hog Ring Pliers |
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
71647D
16.INSTALL REAR SEAT INNER CUSHION EDGE PROTECTOR RH
Install the protector with new tack pins.
17.INSTALL SEAT CUSHION COVER WITH PAD
Using hog ring pliers, install the seatback cover with pad with new hog rings.
| *1 | Hog Ring Pliers |
Install the carpet with new tack pins.
73390C
18.INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY LH
71586
19.INSTALL REAR NO. 2 SEAT HINGE COVER LH
Attach the 3 claws to install the cover.
71585
20.INSTALL REAR NO. 2 SEAT HINGE COVER RH
Attach the 3 claws to install the cover.
72907B
21.INSTALL REAR SEAT CUSHION UNDER COVER SUB-ASSEMBLY RH
Temporarily install the under cover to the seat cushion frame.
72649
22.INSTALL REAR SEAT CUSHION SUPPORT SPRING
Install the spring to the seat cushion frame.
Use the same procedure for both springs.
78917
23.INSTALL FOLD SEAT LEG LOCK CUSHION
Install the cushion to the protector.
Use the same procedure for both cushions.
71647G
24.INSTALL REAR SEAT CUSHION EDGE PROTECTOR
Install the protector to the cushion frame.
Use the same procedure for both protectors.
71305C
25.INSTALL REAR SEAT STAY SUB-ASSEMBLY
Connect the seat stay ball-joint to the seat hinge.
It is only necessary to perform this step when replacing the seat stay and seat hinge. After the seat stay is connected to the seat hinge, it cannot be disconnected.
71301B
26.INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY RH
Install the spring of the seat stay ball-joint.
Temporarily install the seat hinge and seat stay as a unit.
Raise the under cover.
Connect the seat stay to the seat cushion frame.
Connect the reclining release handle to the under cover.
Install the 4 bolts.
Attach the 6 claws to install the under cover.
Install the pin to the hinge.
Install a new E-ring.
71302B
27.INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY LH
Install the hinge.
Install the pin to the hinge.
Install a new E-ring.
72779
28.INSTALL REAR SEAT HINGE PAWL GUIDE
Attach the 4 claws to install the pawl guide.
Use the same procedure for both pawl guides.
72205B
29.INSTALL SEAT TRACK OPEN LEVER PIN SUB-ASSEMBLY
Install the pin as shown in the illustration.
Install the stopper.
Use the same procedure for both pins.
71833A
30.INSTALL REAR NO. 1 SEAT RECLINING COVER RH
Move the cover in the direction of the arrow to attach the guide.
Attach the 2 claws.
Install the cover with the 2 screws.
71834A
31.INSTALL REAR NO. 1 SEAT RECLINING COVER LH
Attach the 2 hooks.
Move the cover in the direction of the arrow to attach the guide.
Attach the 2 claws.
Install the cover with the 2 screws.