Home › Vehicle Interior › SEAT › CLIMATE CONTROL SEAT SWITCH(w/ Climate Control Seat System) › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053737 SEAT _0261143 CLIMATE CONTROL SEAT SWITCH(w/ Climate Control Seat System) G

SEAT  CLIMATE CONTROL SEAT SWITCH(w/ Climate Control Seat System)  INSPECTION  


PROCEDURE

Hide 84752 1.INSPECT REFRESHING SEAT SWITCH LH

a.
B359327E01
0.98,1.399 1.212,1.557 0.232,0.158 10 Off 0.786,0.973 1.019,1.131 0.232,0.158 10 Lo 1.003,0.145 1.235,0.304 0.232,0.158 10 Hi 0.868,1.208 1.221,1.345 0.353,0.137 10 21° 0.811,0.595 1.163,0.732 0.353,0.137 10 42° 2.338,1.658 2.746,1.800 0.408,0.142 10 SW+ 0.808,2.858 1.133,3.000 0.325,0.142 10 SW- 1.725,2.881 2.133,3.023 0.408,0.142 10 BLLH 2.338,2.864 2.533,3.006 0.195,0.142 10 IG 1.438,2.881 1.569,3.023 0.130,0.142 10 E 1.785,1.644 2.086,1.786 0.302,0.142 10 ILL+ 0.792,1.682 1.094,1.824 0.302,0.142 10 ILL- 0.112,3.208 0.953,3.350 0.841,0.142 10 1.5 to 2.8 kΩ 0.295,3.947 0.988,4.089 0.693,0.142 10 29 to 54 Ω 1.192,4.111 1.439,4.283 0.246,0.172 10 (8) 1.566,4.111 1.750,4.265 0.184,0.154 10 21 2.318,4.111 2.642,4.283 0.325,0.172 10 (55) 2.711,4.111 2.894,4.265 0.184,0.154 10 63 2.039,4.111 2.223,4.265 0.184,0.154 10 42 3.052,4.077 3.243,4.240 0.191,0.163 10 (°) 1.894,2.314 2.326,1.833 false 1.785,2.314 1.911,1.833 false 1.538,2.314 1.094,1.851 false 1.894,2.56 2.326,2.855 false 1.785,2.56 1.911,2.855 false 1.667,2.56 1.541,2.855 false 1.538,2.56 1.109,2.855 false 1.201,4.333 1.433,4.492 0.232,0.158 10 Off 2.718,4.333 2.890,4.492 0.172,0.158 10 Hi 1.565,4.333 1.751,4.492 0.186,0.158 10 Lo 1.977,4.333 2.261,4.492 0.283,0.158 10 Mid 0.415,1.615 0.648,1.792 0.232,0.177 10 *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
9 (BLLH) - 11 (SW-) Switch off 1.5 to 2.8 kΩ
Switch on (HI) 29 to 54 Ω


HINT:

As the dial is being turned, the resistance changes gradually.


If the result is not as specified, replace the refreshing seat switch LH.

Text in Illustration
*a Component without harness connected
(Refreshing Seat Switch LH)


b.

Apply battery voltage to the switch connector, and check that the refreshing seat switch LH illuminates.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 3 (ILL+)
Battery negative (-) → 5 (ILL-)
Illuminates


If the result is not as specified, replace the refreshing seat switch LH.


c.

Apply battery voltage to the switch connector, and check that the refreshing seat switch LH indicator illuminates.

OK:
Measurement Condition Switch Condition Specified Condition
Battery positive (+) → 8 (IG)
Battery negative (-) → 10 (E)
Switch on Indicator illuminates


If the result is not as specified, replace the refreshing seat switch LH.


Hide 84752 2.INSPECT REFRESHING SEAT SWITCH RH

a.
B359328E01
2.338,1.658 2.746,1.800 0.408,0.142 10 SVS5 0.619,2.824 1.027,2.966 0.408,0.142 10 SVSG 1.725,2.881 2.133,3.023 0.408,0.142 10 BLRH 2.338,2.864 2.533,3.006 0.195,0.142 10 IG 1.438,2.881 1.569,3.023 0.130,0.142 10 E 1.785,1.644 2.086,1.786 0.302,0.142 10 ILL+ 0.112,3.208 0.953,3.350 0.841,0.142 10 1.5 to 2.8 kΩ 0.295,3.947 0.988,4.089 0.693,0.142 10 29 to 54 Ω 1.192,4.111 1.439,4.283 0.246,0.172 10 (8) 1.566,4.111 1.750,4.265 0.184,0.154 10 21 2.318,4.111 2.642,4.283 0.325,0.172 10 (55) 2.711,4.111 2.894,4.265 0.184,0.154 10 63 2.039,4.111 2.223,4.265 0.184,0.154 10 42 3.052,4.077 3.243,4.240 0.191,0.163 10 (°) 1.894,2.314 2.326,1.833 false 1.785,2.314 1.911,1.833 false 1.894,2.56 2.326,2.855 false 1.785,2.56 1.911,2.855 false 1.667,2.56 1.541,2.855 false 1.538,2.56 1.109,2.855 false 1.201,4.333 1.433,4.492 0.232,0.158 10 Off 2.718,4.333 2.890,4.492 0.172,0.158 10 Hi 1.565,4.333 1.751,4.492 0.186,0.158 10 Lo 1.977,4.333 2.261,4.492 0.283,0.158 10 Mid 0.98,1.399 1.212,1.557 0.232,0.158 10 Off 0.786,0.973 1.019,1.131 0.232,0.158 10 Lo 1.003,0.145 1.235,0.304 0.232,0.158 10 Hi 0.868,1.208 1.221,1.345 0.353,0.137 10 21° 0.811,0.595 1.163,0.732 0.353,0.137 10 42° 0.792,1.682 1.094,1.824 0.302,0.142 10 ILL- 1.538,2.314 1.094,1.851 false 0.415,1.615 0.648,1.792 0.232,0.177 10 *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
9 (BLRH) - 11 (SVSG) Switch off 1.5 to 2.8 kΩ
Switch on (HI) 29 to 54 Ω


HINT:

As the dial is being turned, the resistance changes gradually.


If the result is not as specified, replace the refreshing seat switch RH.

Text in Illustration
*a Component without harness connected
(Refreshing Seat Switch RH)


b.

Apply battery voltage to the switch connector, and check that the refreshing seat switch RH illuminates.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 3 (ILL+)
Battery negative (-) → 5 (ILL-)
Illuminates


If the result is not as specified, replace the refreshing seat switch RH.


c.

Apply battery voltage to the switch connector, and check that the refreshing seat switch RH indicator illuminates.

OK:
Measurement Condition Switch Condition Specified Condition
Battery positive (+) → 8 (IG)
Battery negative (-) → 10 (E)
Switch on Indicator illuminates


If the result is not as specified, replace the refreshing seat switch RH.