Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)
RM27T0E _58 Vehicle Interior _053739 HEATING / AIR CONDITIONING _0261169 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  Cooling Box Circuit  


DESCRIPTION

When the cooler control switch sub-assembly is pushed, the No. 1 cooler blower motor sub-assembly and cooler magnet valve assembly controlled by the air conditioning amplifier assembly and air conditioning amplifier assembly (for the cooling box) operate. If the cooling box assembly does not operate when the cooler control switch sub-assembly is pushed, there may be a problem in the circuit shown below.

WIRING DIAGRAM

E202089E10
5.635,4.969 6,5.135 0.365,0.167 10 false BLW 1.625,0.771 2.177,0.958 0.552,0.188 10 false PANEL 0.375,0.635 1.063,1.063 0.688,0.427 10 false from TAIL Relay 2.448,7.896 2.573,8.063 0.125,0.167 10 false 9 2.448,6.448 2.573,6.615 0.125,0.167 10 false 8 3.198,7.906 3.323,8.073 0.125,0.167 10 false 9 3.188,8.094 3.313,8.26 0.125,0.167 10 false A 3.198,7.438 3.323,7.604 0.125,0.167 10 false 5 3.188,7.625 3.313,7.792 0.125,0.167 10 false A 3.188,6.938 3.313,7.104 0.125,0.167 10 false 4 3.188,7.146 3.313,7.313 0.125,0.167 10 false A 3.188,6.438 3.313,6.604 0.125,0.167 10 false 8 5.365,6.021 5.49,6.188 0.125,0.167 10 false E 5.365,5.76 5.49,5.927 0.125,0.167 10 false E 5.365,5.51 5.49,5.677 0.125,0.167 10 false E 5.365,5.25 5.49,5.417 0.125,0.167 10 false E 5.354,4.979 5.479,5.146 0.125,0.167 10 false E 5.365,8.083 5.49,8.25 0.125,0.167 10 false E 5.365,7.625 5.49,7.792 0.125,0.167 10 false E 5.365,7.156 5.49,7.323 0.125,0.167 10 false E 5.365,6.625 5.49,6.792 0.125,0.167 10 false E 3.177,6.625 3.302,6.792 0.125,0.167 10 false A 3.177,5.833 3.302,6 0.125,0.167 10 false 2 2.448,5.833 2.573,6 0.125,0.167 10 false 2 2.438,0.438 2.563,0.604 0.125,0.167 10 false 3 2.688,5.906 2.813,6.073 0.125,0.167 10 false B 2.698,6.49 2.896,6.656 0.198,0.167 10 false +B 2.719,7.958 2.844,8.125 0.125,0.167 10 false L 5.365,7.885 5.49,8.052 0.125,0.167 10 false 4 5.365,6.448 5.49,6.615 0.125,0.167 10 false 1 5.146,5.917 5.271,6.083 0.125,0.167 10 false 2 5.146,5.656 5.271,5.823 0.125,0.167 10 false 7 5.104,5.406 5.292,5.573 0.188,0.167 10 false 10 5.146,4.865 5.271,5.031 0.125,0.167 10 false 9 5.146,5.156 5.271,5.323 0.125,0.167 10 false 5 5.167,1.729 5.292,1.896 0.125,0.167 10 false 1 5.167,1.49 5.292,1.656 0.125,0.167 10 false 2 5.156,2.625 5.281,2.792 0.125,0.167 10 false 1 5.156,2.927 5.281,3.094 0.125,0.167 10 false 2 5.146,3.51 5.271,3.677 0.125,0.167 10 false 1 5.156,3.844 5.281,4.01 0.125,0.167 10 false 2 5.167,1.229 5.292,1.396 0.125,0.167 10 false 4 5.167,1.01 5.292,1.177 0.125,0.167 10 false 3 5.167,0.781 5.292,0.948 0.125,0.167 10 false 6 5.167,0.521 5.292,0.688 0.125,0.167 10 false 5 5.313,8.354 7.031,8.719 1.719,0.365 10 false Air Conditioning Amplifier Assembly (for Cooling Box) 5.198,4.156 6.917,4.531 1.719,0.375 10 false No. 1 Cooler Blower Motor Sub-assembly 5.01,3.24 7,3.448 1.99,0.208 10 false Cooler Magnet Valve Assembly 5.385,2.073 6.781,2.427 1.396,0.354 10 false Cooler Control Switch Sub-assembly 3.219,8.646 5.073,8.958 1.854,0.313 10 false No. 1 Cooler Wiring Harness Sub-assembly 5.635,8.083 6.156,8.25 0.521,0.167 10 false GND 5.635,6.604 6.156,6.771 0.521,0.167 10 false +B 5.635,6.01 6.156,6.177 0.521,0.167 10 false IG 5.635,7.625 6.156,7.792 0.521,0.167 10 false CBI 5.635,7.156 6.156,7.323 0.521,0.167 10 false CBT 5.635,5.76 6.156,5.927 0.521,0.167 10 false LED 5.635,5.5 6.156,5.667 0.521,0.167 10 false SG 5.635,5.26 6.156,5.427 0.521,0.167 10 false SW 1.552,6.188 2.323,6.354 0.771,0.167 10 false COOLING 1.635,6.781 2.156,6.948 0.521,0.167 10 false ECU-B 0.042,6.042 1.073,6.469 1.031,0.427 10 false from IG1 NO. 2 Relay 0.208,6.604 1.01,6.823 0.802,0.219 10 false from Battery 0.146,8.052 1.74,8.5 1.594,0.448 10 false Air Conditioning Amplifier Assembly 0.552,7.594 1.031,7.76 0.479,0.167 10 false SWCB 0.573,7.125 1.052,7.292 0.479,0.167 10 false COOL 1.104,7.427 1.292,7.594 0.188,0.167 10 false 12 1.104,6.948 1.292,7.115 0.188,0.167 10 false 15 2.448,6.979 2.573,7.146 0.125,0.167 10 false 4 2.448,7.448 2.573,7.615 0.125,0.167 10 false 5 5.365,7.438 5.49,7.604 0.125,0.167 10 false 6 5.365,6.958 5.49,7.125 0.125,0.167 10 false 8 2.406,8.094 2.688,8.26 0.281,0.167 10 false T6 2.406,7.635 2.688,7.802 0.281,0.167 10 false T6 2.406,7.167 2.688,7.333 0.281,0.167 10 false T6 2.406,6.635 2.688,6.802 0.281,0.167 10 false T6 2.406,6.042 2.688,6.208 0.281,0.167 10 false T6 2.406,0.625 2.688,0.792 0.281,0.167 10 false T6 3.188,0.438 3.313,0.604 0.125,0.167 10 false 3 3.177,6.01 3.302,6.177 0.125,0.167 10 false A 3.188,0.625 3.313,0.792 0.125,0.167 10 false A 5.365,3.927 5.49,4.094 0.125,0.167 10 false D 5.365,3.625 5.49,3.792 0.125,0.167 10 false D 5.365,3.042 5.49,3.208 0.125,0.167 10 false C 5.365,2.719 5.49,2.885 0.125,0.167 10 false C 5.365,1.844 5.49,2.01 0.125,0.167 10 false B 5.365,1.594 5.49,1.76 0.125,0.167 10 false B 5.365,1.365 5.49,1.531 0.125,0.167 10 false B 5.365,1.115 5.49,1.281 0.125,0.167 10 false B 5.365,0.875 5.49,1.042 0.125,0.167 10 false B 5.365,0.625 5.49,0.792 0.125,0.167 10 false B 1.052,7.635 1.333,7.802 0.281,0.167 10 false G24 1.052,7.156 1.333,7.323 0.281,0.167 10 false G25 4.042,9.344 5.531,9.542 1.49,0.198 10 false Cooling Box Assembly 2.667,0.552 3.042,0.719 0.375,0.167 10 false ILL+ 2.656,7.51 3.01,7.677 0.354,0.167 10 false ACT 2.667,7.052 3.063,7.219 0.396,0.167 10 false COL1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (COOLING BOX - BATTERY AND BODY GROUND)
a.
U149341E03
1.854,0.979 2.292,0.5 true 1.76,1.219 2.396,1.646 true 1.573,1.229 0.906,1.583 true 1.958,0.281 1.729,0.979 true 2.354,0.417 2.51,0.594 0.156,0.177 10 false B 2.448,1.563 2.677,1.74 0.229,0.177 10 false +B 0.802,1.521 0.958,1.698 0.156,0.177 10 false L 0.115,0.042 0.344,0.219 0.229,0.177 10 false *a 0.688,0.833 0.979,1.01 0.292,0.177 10 false T6 2,0.156 2.365,0.333 0.365,0.177 10 false ILL+

Disconnect the T6 cooling box connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
T6-3 (ILL+) - Body ground Headlight dimmer switch off Below 1 V
T6-3 (ILL+) - Body ground Headlight dimmer switch on 11 to 14 V
T6-2 (B) - Body ground Ignition switch off Below 1 V
T6-2 (B) - Body ground Ignition switch ON 11 to 14 V
T6-8 (+B) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T6-9 (L) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Cooling Box Assembly)


OK

2.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - COOLING BOX)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - COOLING BOX)
a.

Disconnect the G25 and G24 amplifier connectors.


b.

Disconnect the T6 cooling box connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G25-15 (COOL) - T6-4 (COL1) Always Below 1 Ω
G24-12 (SWCB) - T6-5 (ACT) Always Below 1 Ω
G25-15 (COOL) - Body ground Always 10 kΩ or higher
G24-12 (SWCB) - Body ground Always 10 kΩ or higher




OK

3.INSPECT COOLER CONTROL SWITCH SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT COOLER CONTROL SWITCH SUB-ASSEMBLY

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Cooler control switch sub-assembly on Below 1 Ω
1 - 2 Cooler control switch sub-assembly off 10 kΩ or higher



c.

Apply battery voltage to the cooler control switch sub-assembly connector and check that the cooler control switch sub-assembly illuminates.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 3
Battery negative (-) → Terminal 4
LED illuminates
Battery positive (+) → Terminal 5
Battery negative (-) → Terminal 6
LED illuminates




OK

4.INSPECT NO. 1 COOLER BLOWER MOTOR SUB-ASSEMBLY

NG

4.INSPECT NO. 1 COOLER BLOWER MOTOR SUB-ASSEMBLY
a.
E195920

Remove the No. 1 cooler blower motor sub-assembly (See page Vehicle Interior>INTERIOR PANELS / TRIM>FRONT CONSOLE BOX (w/ Refrigerated Cool Box)>DISASSEMBLY).


b.

Apply battery voltage to the No. 1 cooler blower motor sub-assembly and check that the No. 1 cooler blower motor sub-assembly operates smoothly.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 1
Battery negative (-) → Terminal 2
No. 1 cooler blower motor sub-assembly operates smoothly




OK

5.INSPECT NO. 1 COOLER WIRING HARNESS SUB-ASSEMBLY

NG

5.INSPECT NO. 1 COOLER WIRING HARNESS SUB-ASSEMBLY
a.

Remove the No. 1 cooler wiring harness sub-assembly (See page Vehicle Interior>INTERIOR PANELS / TRIM>FRONT CONSOLE BOX (w/ Refrigerated Cool Box)>DISASSEMBLY).

E346099E01
0.281,0.917 0.781,1.167 0.5,0.25 1.063,2.083 1.563,2.333 0.5,0.25 3.542,2.083 4.042,2.333 0.5,0.25 2.5,0.917 3,1.167 0.5,0.25 4.219,0.917 4.719,1.167 0.5,0.25 0.573,0.521 0.823,0.521 0.823,0.521 1.125,0.958 true 1.938,0.521 1.688,0.521 1.688,0.521 1.49,0.948 true 0.844,0.292 1.094,0.292 1.094,0.292 1.219,0.948 true 1.698,0.292 1.448,0.292 1.448,0.292 1.344,0.927 true 0.896,1.521 1.146,1.521 1.146,1.521 1.24,1.188 true 1.75,1.521 1.5,1.521 1.5,1.521 1.365,1.198 true 5.031,0.479 5.281,0.479 5.281,0.479 5.49,0.875 true 6.646,0.479 6.396,0.479 6.396,0.479 6.188,0.896 true 5.063,1.469 5.313,1.469 5.313,1.469 5.51,1.219 true 5.052,1.135 5.302,1.135 true 5.198,1.708 5.448,1.708 5.448,1.708 5.688,1.208 true 6.177,1.719 5.927,1.719 5.927,1.719 5.854,1.219 true 6.406,1.469 6.156,1.469 6.156,1.469 6.021,1.208 true 6.25,1.125 6.5,1.125 true 4.833,0.688 5.083,0.688 5.083,0.688 5.323,0.896 true 0.063,0.063 0.375,0.26 0.313,0.198 10 false *a 0.479,0.958 0.792,1.156 0.313,0.198 10 false A 0.438,0.438 1,0.635 0.563,0.198 10 false B 0.563,0.208 1.125,0.406 0.563,0.198 10 false ILL+ 1.729,0.198 2.292,0.396 0.563,0.198 10 false COL1 1.99,0.417 2.552,0.615 0.563,0.198 10 false ACT 0.688,1.438 1.25,1.635 0.563,0.198 10 false +B 1.833,1.417 2.396,1.615 0.563,0.198 10 false L 1.271,2.125 1.583,2.323 0.313,0.198 10 false B 2.698,0.958 3.01,1.156 0.313,0.198 10 false C 3.75,2.125 4.063,2.323 0.313,0.198 10 false D 4.448,0.958 4.76,1.156 0.313,0.198 10 false E 4.604,0.615 5.167,0.813 0.563,0.198 10 false +B 4.865,0.406 5.427,0.604 0.563,0.198 10 false IG 6.677,0.375 7.083,0.594 0.406,0.219 10 false GND 4.813,1.063 5.375,1.26 0.563,0.198 10 false SW 4.802,1.396 5.365,1.594 0.563,0.198 10 false CBI 4.917,1.625 5.479,1.823 0.563,0.198 10 false LED 6.229,1.635 6.792,1.833 0.563,0.198 10 false CBT 6.458,1.385 7.021,1.583 0.563,0.198 10 false BLW 6.521,1.042 7.083,1.24 0.563,0.198 10 false SG


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-3 (ILL+) - B-5 Always Below 1 Ω
A-2 (B) - E-2 (IG) Always Below 1 Ω
A-8 (+B) - E-1 (+B) Always Below 1 Ω
A-4 (COL1) - E-8 (CBT) Always Below 1 Ω
A-5 (ACT) - E-6 (CBI) Always Below 1 Ω
A-9 (L) - E-4 (GND) Always Below 1 Ω
A-9 (L) - B-6 Always Below 1 Ω
A-2 (B) - B-3 Always Below 1 Ω
B-4 - E-7 (LED) Always Below 1 Ω
B-2 - E-10 (SG) Always Below 1 Ω
B-1 - E-5 (SW) Always Below 1 Ω
A-2 (B) - C-1 Always Below 1 Ω
C-2 - D-2 Always Below 1 Ω
A-2 (B) - D-1 Always Below 1 Ω
D-2 - E-9 (BLW) Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Vehicle Harness)
*b Front view of wire harness connector
(to Cooler Control Switch Sub-assembly)
*c Front view of wire harness connector
(to Cooler Magnet Valve Assembly)
*d Front view of wire harness connector
(to No. 1 Cooler Blower Motor Sub-assembly)
*e Front view of wire harness connector
(to Air Conditioning Amplifier Assembly [for Cooling Box])



OK

NG