Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMPRESSOR(for 1KD-FTV) › 2015.06–2020.08
RM27T0E _58 Vehicle Interior _053739 HEATING / AIR CONDITIONING _0261180 COMPRESSOR(for 1KD-FTV) A

HEATING / AIR CONDITIONING  COMPRESSOR(for 1KD-FTV)  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL MAGNETIC CLUTCH ASSEMBLY

a.
E349903E01
0.167,0.052 0.479,0.25 0.313,0.198 10 false *A 0.167,1.667 0.479,1.865 0.313,0.198 10 false *B 0.167,3.583 0.479,3.781 0.313,0.198 10 false *C

Place the cooler compressor in a vise.


b.

Install the magnet clutch stator with the parts shown in the illustration aligned.

Text in Illustration
*A except Model Code KDJ150L-GKFEYV, KDJ150L-GKAEYV
*B Model Code KDJ150L-GKFEYV, KDJ150L-GKAEYV
*C for Cold Area Specification Vehicles


c.
E349919

Using a snap ring expander, install a new snap ring with the chamfered side facing up.

NOTICE:

When installing the snap ring, do not widen it excessively.



d.

Connect the connector.


e.
E349920

Using a snap ring expander, install the magnet clutch rotor and a new snap ring with the chamfered side facing up.

NOTICE:
·

Do not damage the seal cover of the bearing when installing the snap ring.

·

When installing the snap ring, do not widen it excessively.




f.

Install the magnet clutch washer and magnet clutch hub.

NOTICE:

Do not change the combination of the magnet clutch washers used before disassembly.



g.
E195750E02
2.792,2.854 2.615,2.854 false 2.698,0.792 2.885,0.792 false 0.177,0.167 0.385,0.375 0.208,0.208 10 false *A 0.177,2.375 0.385,2.573 0.208,0.198 10 false *B 2.927,0.708 3.25,0.885 0.323,0.177 10 false SST 2.865,2.771 3.188,2.948 0.323,0.177 10 false SST

Using SST, install the magnet clutch hub and magnet clutch washers with the bolt.

SST
09985-00270  

Text in Illustration
*A except Cold Area Specification Vehicles
*B for Cold Area Specification Vehicles

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)

NOTICE:

Make sure that there is no foreign matter or oil on the compressor shaft, bolt and clutch hub.



Hide 88688K 2.INSTALL COOLER COMPRESSOR BRACKET

a.

Install the cooler bracket with the screw.


b.

Attach the clamp.


Hide 88410 3.INSPECT MAGNETIC CLUTCH CLEARANCE

a.

Set a dial indicator to the magnet clutch hub.

E201201E01
0.116,0.111 0.383,0.304 0.267,0.193 10 *a 1.872,3.146 2.116,3.358 0.244,0.211 10 *1 5.151,3.1 5.394,3.311 0.244,0.211 10 *1 1.844,3.212 1.681,3.212 1.681,3.212 1.194,3.431 false 4.776,3.447 4.976,3.165 4.976,3.165 5.104,3.165 false 0.467,0.111 3.367,3.669 2.9,3.559 3.934,0.117 6.849,3.697 2.914,3.58 0.515,0.157 0.755,0.369 0.239,0.211 10 *A 3.997,0.185 4.209,0.362 0.211,0.177 10 *B

Text in Illustration
*A except Cold Area Specification Vehicles *B for Cold Area Specification Vehicles
*1 Battery - -
*a Component without harness connected
(Magnet Clutch Assembly)
- -


b.

Connect the battery positive (+) lead to terminal 3 of the magnet clutch connector. Turn the magnet clutch on and off by connecting and disconnecting the battery negative (-) lead to and from the ground wire and measure the clearance.

Standard clearance:

0.35 to 0.60 mm (0.013 to 0.024 in.)


If the measured value is not within the standard range, remove the magnet clutch hub and adjust it with magnet clutch washers.

NOTICE:

Adjustment should be performed with 3 magnet clutch washers or less.



Hide 4.ADJUST COMPRESSOR OIL

a.

When replacing the compressor and magnetic clutch with a new one, gradually discharge the refrigerant gas from the service valve and drain the following amount of oil from the new cooler compressor before installation.

Standard:

for Single Air Conditioning System:

(The amount of oil inside a new cooler compressor: 120 to 135 cc (4.1 to 4.6 fl. oz.)) - (The amount of oil remaining in the removed cooler compressor) = (The amount of oil to be removed when replacing the compressor)


Standard:

for Dual Air Conditioning System:

(The amount of oil inside a new cooler compressor: 180 to 195 cc (6.1 to 6.6 fl. oz.)) - (The amount of oil remaining in the removed cooler compressor) = (The amount of oil to be removed when replacing the compressor)


NOTICE:
·

When checking the compressor oil level, follow the A/C system precautions.

·

Since compressor oil remains in the pipes of the vehicle, if a new compressor is installed without removing some oil from the compressor, the oil amount becomes excessive. Excessive oil prevents heat exchange in the refrigerant cycle and causes refrigeration system failure.

·

If the volume of oil remaining in the removed cooler compressor is small, check for oil leakage.

·

Be sure to use ND-OIL 8 for compressor oil.