Home › Vehicle Interior › HEATING / AIR CONDITIONING › HEATER SWITCH › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053739 HEATING / AIR CONDITIONING _0261199 HEATER SWITCH G

HEATING / AIR CONDITIONING  HEATER SWITCH  INSPECTION  


PROCEDURE

Hide 87290 1.INSPECT HEATER SWITCH ASSEMBLY

E166833E11
1.396,1.25 1.01,1.573 true 1.01,1.573 1.01,1.698 false 1.594,1.26 1.458,1.417 false 1.458,1.417 1.458,1.688 true 1.833,1.26 1.917,1.417 true 1.917,1.417 1.917,1.698 true 2.021,1.26 2.375,1.417 true 2.375,1.417 2.375,1.698 true 0.135,0.104 0.313,0.281 0.177,0.177 10 false *a 0.896,1.698 1.177,1.885 0.281,0.188 10 false +S 2.323,1.698 2.469,1.885 0.146,0.188 10 false E 1.333,1.698 1.688,1.885 0.354,0.188 10 false ILL+ 1.802,1.698 2.156,1.885 0.354,0.188 10 false ILL-

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
6 (+S) - 3 (E) Heater switch assembly off 10 kΩ or higher
Heater switch assembly on Below 1 Ω



b.

Apply battery voltage to the connector and check the LED illumination.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 5 (ILL+)
Battery negative (-) → Terminal 4 (ILL-)
LED illuminates


Text in Illustration
*a Component without harness connected
(Heater Switch Assembly)

If the result is not as specified, there may be a malfunction in the heater switch assembly.


Hide 84453 2.INSPECT IDLE UP SWITCH

E166833E12
1.396,1.25 1.01,1.573 true 1.01,1.573 1.01,1.698 false 1.583,1.25 1.448,1.406 true 1.448,1.406 1.448,1.677 true 1.833,1.26 1.917,1.417 true 1.917,1.417 1.917,1.698 true 2.021,1.26 2.375,1.417 true 2.375,1.417 2.375,1.698 true 0.135,0.115 0.313,0.292 0.177,0.177 10 false *a 0.896,1.698 1.177,1.885 0.281,0.188 10 false SW 2.323,1.708 2.469,1.896 0.146,0.188 10 false E 1.365,1.698 1.719,1.885 0.354,0.188 10 false ILL+ 1.802,1.708 2.156,1.896 0.354,0.188 10 false ILL-

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
6 (SW) - 3 (E) Idle up switch off 10 kΩ or higher
Idle up switch on Below 1 Ω



b.

Apply battery voltage to the connector and check the LED illumination.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 5 (ILL+)
Battery negative (-) → Terminal 4 (ILL-)
LED illuminates


Text in Illustration
*a Component without harness connected
(Idle Up Switch)

If the result is not as specified, there may be a malfunction in the idle up switch.