Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMBUSTION TYPE POWER HEATER SYSTEM
RM27T0E _58 Vehicle Interior _053739 HEATING / AIR CONDITIONING _0261205 COMBUSTION TYPE POWER HEATER SYSTEM J

HEATING / AIR CONDITIONING  COMBUSTION TYPE POWER HEATER SYSTEM  Power Heater Fuel Pump Circuit  


DESCRIPTION

When the heater switch assembly (power heater switch) is turned on, the heater pump assembly receives a drive voltage from the heater assembly. The heater pump assembly provides the heater assembly with fuel necessary for combustion, allowing the heater assembly to operate.

WIRING DIAGRAM

E267498E03
5.302,1.74 5.76,1.938 0.458,0.198 10 false A97 5.302,1.906 6.677,2.115 1.375,0.208 10 false Heater Assembly 2.698,1.365 3.156,1.563 0.458,0.198 10 false A96 2.698,1.542 4.281,1.74 1.583,0.198 10 false Heater Pump Assembly 5.427,1.01 5.885,1.208 0.458,0.198 10 false L 3.656,1.115 3.896,1.323 0.24,0.208 10 false B2 2.844,1.115 3.302,1.313 0.458,0.198 10 false E2 2.635,0.885 2.771,1.073 0.135,0.188 10 false 1 3.938,0.865 4.396,1.063 0.458,0.198 10 false 2 5.198,0.885 5.365,1.063 0.167,0.177 10 false 2

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (HEATER ASSEMBLY - HEATER PUMP ASSEMBLY)
a.

Disconnect the A97 heater assembly connector.


b.

Disconnect the A96 heater pump assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A97-2 (L) - A96-1 (B2) Always Below 1 Ω
A97-2 (L) - Body ground Always 10 kΩ or higher




OK

2.CHECK HARNESS AND CONNECTOR (HEATER PUMP ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (HEATER PUMP ASSEMBLY - BODY GROUND)
a.
U170672E02
1.594,1.448 1.417,1.844 1.417,1.844 1.167,1.844 true 0.167,0 0.458,0.167 0.292,0.167 10 false *a 0.948,1.76 1.271,1.969 0.323,0.208 10 false E2 0.469,0.729 0.823,0.938 0.354,0.208 10 false A96

Disconnect the heater pump assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A96-1 (E2) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Heater Pump Assembly)



OK

3.INSPECT HEATER PUMP ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT HEATER PUMP ASSEMBLY
a.
E176914E13
2.47,1.489 2.673,1.659 0.203,0.170 10 E2 0.777,1.498 0.980,1.668 0.203,0.170 10 B2 2.451,1.545 1.996,1.197 false 1.029,1.565 1.484,1.217 false

Remove the heater pump assembly (See page Vehicle Interior>HEATING / AIR CONDITIONING>HEATER FUEL PUMP>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (B2) - 1 (E2) Always 9 to 12 Ω



c.

Inspect heater pump assembly operation.

i.

Connect a positive (+) lead from the battery to terminal 2 (B2) and a negative (-) lead to terminal 1 (E2), and check the pressure of the hose by hand.

NOTICE:

This inspection must be done quickly (within 10 seconds) to prevent damage to the heater pump assembly.




Result
Result Proceed to
The pressure is applied to the hose A
The pressure is not applied to the hose B


A

4.CHECK HEATER ASSEMBLY

B

4.CHECK HEATER ASSEMBLY
a.
U170673E02
1.833,1.458 2.229,1.917 2.229,1.917 2.458,1.917 true 0.167,0 0.458,0.167 0.292,0.167 10 false *a 2.51,1.844 2.833,2.052 0.323,0.208 10 false B2 0.313,1.063 0.667,1.271 0.354,0.208 10 false A96

Disconnect the heater pump assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A96-2 (B2) - Body ground Engine running, heater switch assembly (power heater switch) on 11 to 14 V
A96-2 (B2) - Body ground Engine running, heater switch assembly (power heater switch) off Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Heater Pump Assembly)



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG