Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMBUSTION TYPE POWER HEATER SYSTEM
RM27T0E _58 Vehicle Interior _053739 HEATING / AIR CONDITIONING _0261205 COMBUSTION TYPE POWER HEATER SYSTEM C

HEATING / AIR CONDITIONING  COMBUSTION TYPE POWER HEATER SYSTEM  016  Difference Evaluation 2  020  Glow Plug Malfunction  021  Glow Plug Output Overload  022  Glow Plug Output Error  025  Short in K-line Circuit  030  Abnormal Combustion Air Blower Motor Speed  031  Combustion Air Blower Motor Malfunction  032  Short in Combustion Air Blower Motor Circuit  034  Combustion Air Blower Motor Output Error  060  Overheating Control Sensor Malfunction  061  Short in Overheating Control Sensor Circuit  064  Flame Sensor Malfunction  065  Short in Flame Sensor Circuit  071  Surface Sensor Malfunction  072  Short in Surface Sensor Circuit  074  ECU Overheating  090  ECU Internal Malfunction / Reset Detection  091  Repeated Resets Detection  092  ROM Error  093  RAM Error  094  Transistor Malfunction  095  Software Stuck Overflow  096  Operation Locked Detection  097  ECU Defects  098  Main Relay Malfunction  099  EEPROM Error  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
016 The difference in temperatures detected by the surface sensor and control overheating sensor is 30°C (86°F) or higher.
·

Heater assembly (surface sensor)

·

Heater assembly (control overheating sensor)


020 Operation stop of the glow plug is detected. (Open in the circuit)
·

Heater assembly (glow plug)

·

Heater assembly (harness or connector)


021 Overload on the glow plug or a short in the wire harness that is connected to the glow plug is detected.
·

Heater assembly (glow plug)

·

Heater assembly (harness or connector)


022 An error is detected in output from the power heater ECU to the glow plug, or a problem with the wire harness that is connected to the glow plug is detected.
·

Heater assembly (ECU)

·

Heater assembly (harness or connector)


025 A short circuit is detected in the diagnostic communication line in the heater assembly. Heater assembly
030 Air blower motor speed is out of the allowable range (8800 rpm to 10400 rpm). (An object may be caught in or between parts around the air blower motor.) Heater assembly (air blower motor)
031 Operation stop of the air blower motor is detected. (Open in the circuit)
·

Heater assembly (air blower motor)

·

Heater assembly (harness or connector)


032 A short circuit is detected in the wire harness which is connected to the air blower motor. Heater assembly (harness or connector)
034 An error is detected in output from the power heater ECU to the air blower motor, or a problem with the wire harness that is connected to the air blower motor is detected.
·

Heater assembly (ECU)

·

Heater assembly (harness or connector)


060 Operation stop of the control overheating sensor is detected. (Open in the circuit) Heater assembly (control overheating sensor)
061 A short is detected in the control overheating sensor circuit.
·

Heater assembly (control overheating sensor)

·

Heater assembly (harness or connector)


064 Operation stop of the flame sensor is detected. (Open in the circuit) Heater assembly (flame sensor)
065 A short is detected in the flame sensor circuit.
·

Heater assembly (flame sensor)

·

Heater assembly (harness or connector)


071 Operation stop of the surface sensor is detected. (Open in the circuit) Heater assembly (surface sensor)
072 A short is detected in the surface sensor circuit.
·

Heater assembly (surface sensor)

·

Heater assembly (harness or connector)


074 The heater assembly (ECU) stops operating due to overheating. Heater assembly (ECU)
090 An internal malfunction of the control unit is detected. Heater assembly (ECU)
091 Reset operation is repeated too many times. Heater assembly (ECU)
092 A control unit (ROM) error is detected. Heater assembly (ECU)
093 A control unit (RAM) error is detected. Heater assembly (ECU)
094 A transistor malfunction due to frequent operation interruptions is detected. Heater assembly (ECU)
095 A software stuck overflow is detected. Heater assembly (ECU)
096 An operation lock due to the absence of valid process is detected. Heater assembly (ECU)
097 An internal control unit malfunction is detected. Heater assembly (ECU)
098 A main relay malfunction is detected. Heater assembly (ECU)
099 An EEPROM error is detected. Heater assembly (ECU)

PROCEDURE

1.REPLACE HEATER ASSEMBLY
a.


NEXT

END