Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMBUSTION TYPE POWER HEATER SYSTEM
RM27T0E _58 Vehicle Interior _053739 HEATING / AIR CONDITIONING _0261205 COMBUSTION TYPE POWER HEATER SYSTEM C

HEATING / AIR CONDITIONING  COMBUSTION TYPE POWER HEATER SYSTEM  050  Detection of No Ignition  052  Safety Time Exceeded  054  High Setting of Flame Cutout  056  Low Setting of Flame Cutout  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
050 The ECU is locked as a result of 10 successive heater ignition failures.
·

Intake air duct

·

Exhaust air duct

·

Fuel pump filter

·

Heater pump assembly

·

Heater assembly


052 A heater ignition failure is detected.
·

Intake air duct

·

Exhaust air duct

·

Fuel pump filter

·

Heater pump assembly

·

Heater assembly


054 Combustion ends abnormally (High output operation).
·

Intake air duct

·

Exhaust air duct

·

Fuel pump filter

·

Heater pump assembly

·

Heater assembly


056 Combustion ends abnormally (Low output operation).
·

Intake air duct

·

Exhaust air duct

·

Fuel pump filter

·

Heater pump assembly

·

Heater assembly



CAUTION / NOTICE / HINT

HINT:
·

Clear the DTCs by pressing the memory clear buttons on the DTC tester to unlock the ECU.

·

Before performing the following procedure, attempt to restart the heater assembly. If the heater assembly is successfully started, confirm that neither DTC 054 nor DTC 056 is output. If neither DTC 054 nor 056 is output, finish troubleshooting because it can be concluded that the system has returned to normal operation.



PROCEDURE

1.INSPECT INTAKE AIR DUCT
a.

Inspect the intake air duct.


Result
Result Proceed to
There is no problem with the intake air duct A
The intake air duct is clogged, or other problems are found B


A

2.INSPECT EXHAUST AIR DUCT

B

CLEAN OR REPLACE INTAKE AIR DUCT

2.INSPECT EXHAUST AIR DUCT
a.

Inspect the exhaust air duct.


Result
Result Proceed to
There is no problem with the exhaust air duct A
The exhaust air duct is clogged, or other problems are found B


A

3.INSPECT HEATER PUMP ASSEMBLY

B

CLEAN OR REPLACE EXHAUST AIR DUCT

3.INSPECT HEATER PUMP ASSEMBLY
a.
E176914E13
2.47,1.489 2.673,1.659 0.203,0.170 10 E2 0.777,1.498 0.980,1.668 0.203,0.170 10 B2 2.451,1.545 1.996,1.197 false 1.029,1.565 1.484,1.217 false

Remove the heater pump assembly (See page Vehicle Interior>HEATING / AIR CONDITIONING>HEATER FUEL PUMP>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (B2) - 1 (E2) Always 9 to 12 Ω



c.

Inspect heater pump assembly operation.

i.

Connect a positive (+) lead from the battery to terminal 2 (B2) and a negative (-) lead to terminal 1 (E2), and check the pressure of the hose by hand.

NOTICE:

This inspection must be done quickly (within 10 seconds) to prevent damage to the heater pump assembly.




Result
Result Proceed to
The pressure is applied to the hose A
The pressure is not applied to the hose B


A

4.CHECK FUEL PUMP FILTER

B

4.CHECK FUEL PUMP FILTER
a.

Replace the fuel pump filter with a new one and check that the condition returns to normal.

OK:

The heater is ignited normally and starts operating.




OK

END (FUEL PUMP FILTER IS DEFECTIVE)

NG