Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
84010A
1.REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY
55436A
2.REMOVE INSTRUMENT PANEL FINISH PANEL END LH
Detach the 4 clips and remove the instrument panel finish panel end LH.
55449C
3.REMOVE NO. 2 INSTRUMENT PANEL FINISH PANEL CUSHION
Detach the 5 clips and remove the No. 2 instrument panel finish panel cushion.
55435A
4.REMOVE INSTRUMENT PANEL FINISH PANEL END RH
Detach the 4 clips and remove the instrument panel finish panel end RH.
55448A
5.REMOVE NO. 1 INSTRUMENT PANEL FINISH PANEL CUSHION
Use the same procedure described for the No. 2 instrument panel finish panel cushion.
58831A
6.REMOVE FRONT CONSOLE UPPER PANEL GARNISH
w/o Seat Heater System:
Put protective tape around the front console upper panel garnish.
| *1 | Protective Tape |
Detach the 5 clips and remove the front console upper panel garnish.
Disconnect the connector.
w/o CRAWL:
Put protective tape around the front console upper panel garnish.
| *1 | Protective Tape |
Detach the 5 clips and remove the front console upper panel garnish.
Disconnect each connector.
w/ CRAWL:
Put protective tape around the front console upper panel garnish.
| *1 | Protective Tape |
Detach the 5 clips and remove the front console upper panel garnish.
55606
7.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
for LHD:
Remove the screw.
Detach the 2 clips and 2 guides and remove the No. 1 instrument panel under cover.
Disconnect each connector.
for RHD:
Remove the screw.
Detach the 3 clips and 2 guides and remove the No. 1 instrument panel under cover.
Disconnect each connector.
58816B
8.REMOVE FRONT NO. 1 CONSOLE BOX INSERT
Detach the 2 clips and guide and remove the front No. 1 console box insert.
55607
9.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
Remove the screw.
Detach the 3 clips and 2 guides and remove the No. 2 instrument panel under cover.
| *A | for LHD | *B | for RHD |
58817A
10.REMOVE FRONT NO. 2 CONSOLE BOX INSERT
Detach the 2 clips and guide and remove the front No. 2 console box insert.
33504F
11.REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY
Move the shifting hole cover downward.
| *1 | Shifting Hole Cover |
Twist the shift lever knob in the direction indicated by the arrow and remove it.
12.REMOVE CONSOLE PANEL SUB-ASSEMBLY
Put protective tape around the console panel.
| *1 | Protective Tape |
Using a moulding remover, detach the 8 clips and 2 claws.
Disconnect each connector and remove the console panel.
55084E
13.REMOVE NO. 1 HEATER TO REGISTER DUCT SUB-ASSEMBLY (w/ Cool Box)
Detach the 4 claws.
Disconnect the 2 clamps and remove the No. 1 heater to register duct.
58861B
14.REMOVE NO. 1 CONSOLE BOX DUCT (for Single Air Conditioning System)
Remove the clip and No. 1 console box duct.
58903A
15.REMOVE REAR CONSOLE END PANEL SUB-ASSEMBLY
Detach the 4 clips and 4 claws.
Disconnect each connector and remove the rear console end panel.
58910C
16.REMOVE REAR CONSOLE BOX ASSEMBLY
Remove the 2 screws, clip and 5 bolts.
Disconnect each connector and remove the rear console box.