Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW REGULATOR MOTOR (for Rear Door)
RM27T0E _59 Vehicle Exterior _053742 WINDOW / GLASS _0261233 POWER WINDOW REGULATOR MOTOR(for Rear Door) G

WINDOW / GLASS  POWER WINDOW REGULATOR MOTOR(for Rear Door)  INSPECTION  


PROCEDURE

Hide 85720G 1.INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

a.
B412035E01
1.577,1.41 1.203,0.418 1.203,0.418 1.097,0.418 false 0.873,0.309 1.093,0.493 0.221,0.184 10 *1 0.22,1.202 0.482,1.386 0.262,0.184 10 *a 0.892,3.087 1.252,3.271 0.360,0.184 10 B 2.493,3.145 2.853,3.329 0.360,0.184 10 GND 0.755,3.875 1.114,4.059 0.360,0.184 10 UP 2.428,3.852 2.927,4.036 0.499,0.184 10 DOWN 1.102,2.078 1.359,2.286 0.257,0.208 10 *b 1.037,3.205 1.612,3.428 false 1.539,3.784 1.049,3.943 false 2.437,3.222 1.862,3.445 false 1.924,3.764 2.414,3.923 false

Apply positive (+) battery voltage to the connector terminal 2 (B).

NOTICE:

Do not apply positive (+) battery voltage to any terminals except terminal 2 (B) to avoid damaging the pulse sensor inside the motor.



b.

Apply negative (-) battery voltage to the connector terminals 1 (GND) and 7 (DOWN) or 10 (UP).


c.

Check that the motor gear rotates smoothly as follows.

OK:
Measurement Condition Specified Condition
1.

Connect the positive (+) battery cable to terminal 2 (B), and connect the negative (-) battery cable to terminal 1 (GND), and keep them connected for 3 seconds or more.

2.

With terminals 2 (B) and 1 (GND) connected, connect the negative (-) battery cable to terminal 10 (UP).

3.

Disconnect and reconnect the negative (-) battery cable to terminal 10 (UP) within 1 second.


Motor gear rotates clockwise (Up)
1.

Connect the positive (+) battery cable to terminal 2 (B), and connect the negative (-) battery cable to terminal 1 (GND), and keep them connected for 3 seconds or more.

2.

With terminals 2 (B) and 1 (GND) connected, connect the negative (-) battery cable to terminal 7 (DOWN).

3.

Disconnect and reconnect the negative (-) battery cable to terminal 7 (DOWN) within 1 second.


Motor gear rotates counterclockwise (Down)


If the result is not as specified, replace the rear power window regulator motor assembly LH.


CAUTION:

Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly onto the door.


Text in Illustration
*1 Motor Gear
*a Clockwise
*b Counterclockwise


Hide 85710F 2.INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

a.
B412034E01
1.732,1.483 1.358,0.491 1.358,0.491 1.252,0.491 false 1.033,0.382 1.249,0.566 0.216,0.184 10 *1 2.901,1.21 3.121,1.394 0.220,0.184 10 *b 0.875,3.092 1.235,3.275 0.360,0.184 10 B 2.419,3.206 2.779,3.390 0.360,0.184 10 GND 0.757,3.905 1.116,4.089 0.360,0.184 10 UP 2.42,3.928 2.918,4.111 0.499,0.184 10 DOWN 2.117,2.101 2.519,2.341 0.402,0.240 10 *a 1.03,3.211 1.605,3.434 false 1.871,3.434 2.393,3.305 false 1.536,3.769 1.115,3.915 false 1.932,3.777 2.387,3.935 false

Apply positive (+) battery voltage to the connector terminal 2 (B).

NOTICE:

Do not apply positive (+) battery voltage to any terminals except terminal 2 (B) to avoid damaging the pulse sensor inside the motor.



b.

Apply negative (-) battery voltage to the connector terminals 1 (GND) and 7 (DOWN) or 10 (UP).


c.

Check that the motor gear rotates smoothly as follows.

OK:
Measurement Condition Specified Condition
1.

Connect the positive (+) battery cable to terminal 2 (B), and connect the negative (-) battery cable to terminal 1 (GND), and keep them connected for 3 seconds or more.

2.

With terminals 2 (B) and 1 (GND) connected, connect the negative (-) battery cable to terminal 10 (UP).

3.

Disconnect and reconnect the negative (-) battery cable to terminal 10 (UP) within 1 second.


Motor gear rotates counterclockwise (Up)
1.

Connect the positive (+) battery cable to terminal 2 (B), and connect the negative (-) battery cable to terminal 1(GND), and keep them connected for 3 seconds or more.

2.

With terminals 2 (B) and 1 (GND) connected, connect the negative (-) battery cable to terminal 7 (DOWN).

3.

Disconnect and reconnect the negative (-) battery cable to terminal 7 (DOWN) within 1 second.


Motor gear rotates clockwise (Down)


If the result is not as specified, replace the rear power window regulator motor assembly RH.


CAUTION:

Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly onto the door.


Text in Illustration
*1 Motor Gear
*a Clockwise
*b Counterclockwise