Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF SYSTEM › 2015.06–2016.08
RM27T0E _59 Vehicle Exterior _053743 SLIDING ROOF / CONVERTIBLE _0261242 SLIDING ROOF SYSTEM J

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF SYSTEM  Sliding Roof Control Switch Circuit  


DESCRIPTION

The sliding roof drive gear sub-assembly receives map light assembly signals and drives its built-in motor.

WIRING DIAGRAM

B243239E01
0.102,0.98 1.190,1.178 1.088,0.198 10 IG1 NO. 1 Relay 1.567,1.163 2.571,1.345 1.004,0.182 10 ECU-IG NO. 2 3.946,2.045 4.409,2.227 0.462,0.182 10 OPN 2.828,2.038 3.183,2.219 0.354,0.182 10 OPN 3.945,2.358 4.470,2.540 0.525,0.182 10 CLS 2.846,2.346 3.166,2.528 0.320,0.182 10 CLS 3.952,2.668 4.415,2.850 0.462,0.182 10 UP 2.925,2.668 3.159,2.850 0.233,0.182 10 UP 3.941,2.982 4.452,3.164 0.511,0.182 10 DWN 2.675,2.992 3.186,3.174 0.511,0.182 10 DOWN 4.57,2.197 5.390,2.573 0.820,0.376 10 Sliding Roof ECU 5.624,1.278 6.851,1.487 1.227,0.209 10 Sliding Roof Motor 1.085,3.461 3.790,3.859 2.704,0.398 10 Map Light Assembly (Sliding Roof Switch) 3.914,5.061 6.419,5.243 2.505,0.181 10 Sliding Roof Drive Gear Sub-assembly 5.886,2.228 6.374,2.437 0.488,0.209 10 Hall IC 5.886,2.986 6.374,3.195 0.488,0.209 10 Hall IC 3.742,1.744 3.861,1.893 0.120,0.149 10 5 3.738,2.045 3.858,2.195 0.120,0.149 10 7 3.738,2.366 3.858,2.515 0.120,0.149 10 9 3.679,2.672 3.875,2.822 0.196,0.149 10 10 3.239,2.048 3.435,2.198 0.196,0.149 10 27 1.265,2.209 1.461,2.358 0.196,0.149 10 5 3.233,2.365 3.429,2.515 0.196,0.149 10 28 3.237,2.674 3.433,2.823 0.196,0.149 10 24 3.229,2.991 3.425,3.140 0.196,0.149 10 25 3.241,1.748 3.437,1.898 0.196,0.149 10 23 3.738,2.992 3.858,3.141 0.120,0.149 10 8 2.723,1.462 2.842,1.611 0.120,0.149 10 8 3.952,1.738 4.206,1.908 0.254,0.170 10 IG 2.478,1.703 2.732,1.874 0.254,0.170 10 IG 2.902,1.74 3.156,1.910 0.254,0.170 10 IG3 1.085,3.309 1.339,3.479 0.254,0.170 10 W7 3.917,4.909 4.171,5.079 0.254,0.170 10 W2 3.735,3.852 3.854,4.001 0.120,0.149 10 2 3.952,3.84 4.205,4.010 0.254,0.170 10 E 1.459,2.213 1.890,2.383 0.431,0.170 10 GND3 0.105,0.833 0.536,1.003 0.431,0.170 10 from

CAUTION / NOTICE / HINT

NOTICE:

When the sliding roof drive gear sub-assembly is removed and reinstalled or replaced, the sliding roof drive gear sub-assembly must be initialized (See page Vehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION).


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SLIDING ROOF)
a.

Select the Active Test, use the intelligent tester to generate a control command, and then check that the sliding roof slides open/closed and tilts up/down (See page Vehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DATA LIST / ACTIVE TEST).

Sliding Roof
Tester Display Test Part Control Range Diagnostic Note
Slide Roof Operate sliding roof Opn/Dwn: Sliding roof slide open or tilt down operation occurs
Clos/Up: Sliding roof slide close or tilt up operation occurs
OFF: Sliding roof not operating
-

OK:

The sliding roof operates normally.




OK

2.READ VALUE USING INTELLIGENT TESTER (SLIDING ROOF)

NG

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY

2.READ VALUE USING INTELLIGENT TESTER (SLIDING ROOF)
a.

Using the intelligent tester, read the Data List (See page Vehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DATA LIST / ACTIVE TEST).

Sliding Roof
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Open Switch Slide open switch signal / ON or OFF ON: Slide open switch pressed
OFF: Slide open switch not pressed
-
Close Switch Slide close switch signal / ON or OFF ON: Slide close switch pressed
OFF: Slide close switch not pressed
-
Up Switch Tilt up switch signal / ON or OFF ON: Tilt up switch pressed
OFF: Tilt up switch not pressed
-
Down Switch Tilt down switch signal / ON or OFF ON: Tilt down switch pressed
OFF: Tilt down switch not pressed
-

OK:

When operating the switch, the intelligent tester displays as shown in the table.




OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY

NG

3.INSPECT MAP LIGHT ASSEMBLY
3.INSPECT MAP LIGHT ASSEMBLY
B240415E11
0.823,1.396 0.427,0.885 false 1.865,1.802 1.656,1.26 false 2.302,1.802 2.042,1.25 false 1.24,1.375 1.313,0.604 false 0.958,1.385 0.885,0.677 false 1.354,1.385 1.927,0.635 false 1.51,1.396 1.26,1.833 false 0.135,0.042 0.385,0.219 0.25,0.177 10 false *a 1.823,1.823 2.052,2 0.229,0.177 10 false IG 2.323,1.813 2.75,1.99 0.427,0.177 10 false GND3 1.177,1.854 1.521,2.031 0.344,0.177 10 false IG3 0.604,0.458 0.979,0.635 0.375,0.177 10 false OPN 0.115,0.677 0.469,0.854 0.354,0.177 10 false CLS 1.135,0.385 1.625,0.563 0.49,0.177 10 false DOWN 1.958,0.448 2.198,0.625 0.24,0.177 10 false UP

a.

Remove the map light assembly (See page Vehicle Interior>LIGHTING (INT)>ROOM LIGHT(for Front)>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
8 (IG) - 23 (IG3) Always Below 1 Ω
24 (UP) - 5 (GND3) Tilt up switch pressed Below 1 Ω
24 (UP) - 5 (GND3) Tilt up switch not pressed 10 kΩ or higher
25 (DOWN) - 5 (GND3) Tilt down switch pressed Below 1 Ω
25 (DOWN) - 5 (GND3) Tilt down switch not pressed 10 kΩ or higher
27 (OPN) - 5 (GND3) Slide open switch pressed Below 1 Ω
27 (OPN) - 5 (GND3) Slide open switch not pressed 10 kΩ or higher
28 (CLS) - 5 (GND3) Slide close switch pressed Below 1 Ω
28 (CLS) - 5 (GND3) Slide close switch not pressed 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Map Light Assembly)



OK

4.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - SLIDING ROOF SWITCH, BATTERY AND BODY GROUND)

NG

4.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - SLIDING ROOF SWITCH, BATTERY AND BODY GROUND)
a.

Disconnect the W2 ECU connector.


b.

Disconnect the W7 switch connector.


c.

Measure the resistance and voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W2-10 (UP) - W7-24 (UP) Always Below 1 Ω
W2-8 (DWN) - W7-25 (DOWN) Always Below 1 Ω
W2-7 (OPN) - W7-27 (OPN) Always Below 1 Ω
W2-9 (CLS) - W7-28 (CLS) Always Below 1 Ω
W7-5 (GND3) - Body ground Always Below 1 Ω
W2-2 (E) - Body ground Always Below 1 Ω
W2-5 (IG) - W7-23 (IG3) Always Below 1 Ω
W2-10 (UP) or W7-24 (UP) - Body ground Always 10 kΩ or higher
W2-8 (DWN) or W7-25 (DOWN) - Body ground Always 10 kΩ or higher
W2-7 (OPN) or W7-27 (OPN) - Body ground Always 10 kΩ or higher
W2-9 (CLS) or W7-28 (CLS) - Body ground Always 10 kΩ or higher
W2-5 (IG) or W7-23 (IG3) - Body ground Always 10 kΩ or higher


Standard Voltage:
Tester Connection Switch Condition Specified Condition
W7-8 (IG) - Body ground Ignition switch off Below 1 V
W7-8 (IG) - Body ground Ignition switch ON 11 to 14 V




OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR