Home › Vehicle Exterior › DOOR / HATCH › HOOD LOCK CONTROL CABLE ASSEMBLY › 2015.06–2017.08
RM27T0E _59 Vehicle Exterior _053744 DOOR / HATCH _0261246 HOOD LOCK CONTROL CABLE ASSEMBLY A

DOOR / HATCH  HOOD LOCK CONTROL CABLE ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).


PROCEDURE

Hide 53630 1.INSTALL HOOD LOCK CONTROL CABLE ASSEMBLY (for LHD)

a.

Pass the hood lock control cable assembly into the engine compartment.


b.

Pass the cable through the upper radiator support.


c.

Attach the clamps as shown in the illustration.

U147999E01
4.719,0.411 4.887,0.577 0.168,0.166 10 *1 1.725,2.148 1.893,2.314 0.168,0.166 10 *2 2.44,1.642 2.608,1.807 0.168,0.166 10 *1 0.954,1.644 1.123,1.810 0.168,0.166 10 *2 0.371,1.648 0.539,1.814 0.168,0.166 10 *1 5.978,1.112 6.146,1.278 0.168,0.166 10 *1 6.222,2.477 6.390,2.643 0.168,0.166 10 *1 0.521,1.716 0.73,1.716 false 0.943,1.706 0.875,1.706 0.875,1.706 0.812,1.987 false 1.797,2.126 1.797,1.992 1.797,1.992 1.914,1.905 false 2.404,1.699 2.36,1.699 2.36,1.699 2.268,1.905 false 6.368,2.544 6.496,2.544 6.496,2.544 6.662,2.793 false 6.11,1.183 6.191,1.183 6.191,1.183 6.289,1.412 false 4.87,0.478 5.052,0.478 5.052,0.478 5.145,0.728 false 1.323,1.409 1.539,1.616 0.216,0.207 10 *A

Text in Illustration
*A for Engine Room Side - -
*1 Hood Lock Control Cable *2 Stopper


Hide 53630 2.INSTALL HOOD LOCK CONTROL CABLE ASSEMBLY (for RHD)

a.

Pass the hood lock control cable assembly into the engine compartment.


b.

Pass the cable through the upper radiator support.


c.

Attach the clamps as shown in the illustration.

U169727E02
4.583,1.75 4.75,1.75 4.75,1.75 4.917,1.917 true 6,2 6,1.844 true 6.667,2.25 6.667,2.042 true 5.125,1.667 5,1.667 true 2.281,0.833 2.281,1 true 0.917,0.833 0.917,1 true 0.948,2.042 0.948,2.219 true 1.5,3.25 1.313,3.302 1.313,3.302 1.313,3.396 true 2.208,0.885 2.125,1 2.125,1 1.917,1 true 0.865,2.094 0.781,2.24 0.781,2.24 0.583,2.24 true 0.927,0.708 1,0.583 1,0.583 1.083,0.583 true 2.198,1 2.417,1.188 0.219,0.188 10 false *1 1.75,0.917 1.969,1.104 0.219,0.188 10 false *3 0.833,1 1.01,1.167 0.177,0.167 10 false *1 0.896,2.229 1.073,2.385 0.177,0.156 10 false *1 1.25,3.417 1.469,3.688 0.219,0.271 10 false *1 4.448,1.667 4.667,1.938 0.219,0.271 10 false *2 6.615,2.25 6.833,2.521 0.219,0.271 10 false *1 5.167,1.583 5.385,1.854 0.219,0.271 10 false *1 5.948,2 6.167,2.271 0.219,0.271 10 false *2 5.521,1.323 5.75,1.531 0.229,0.208 10 false *A 0.417,2.167 0.635,2.354 0.219,0.188 10 false *3 1.115,0.5 1.333,0.688 0.219,0.188 10 false *3

Text in Illustration
*A for Engine Room Side - -
*1 Hood Lock Control Cable *2 Stopper


Hide 53601 3.INSTALL HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

a.

for LHD:

i.
B238482

Connect the hood lock control cable assembly to the hood lock control lever sub-assembly.


ii.
B246507

Attach the 3 claws to install the hood lock control lever sub-assembly.


iii.
B246473E05
0.302,1.875 0.938,1.875 0.938,1.875 1.531,1.323 true 1.167,1.229 1.344,1.229 1.344,1.229 1.427,1.115 true 1.427,1.958 1.604,1.958 1.604,1.958 1.604,1.51 true 1.677,0.688 1.51,0.688 true 0.083,1.792 0.25,2.042 0.167,0.25 10 true *1 0.969,1.156 1.167,1.417 0.198,0.26 10 true *2 1.708,0.594 1.917,0.833 0.208,0.24 10 true *3 1.229,1.896 1.417,2.167 0.188,0.271 10 true *4

Attach the clamps as shown in the illustration.

Text in Illustration
*1 Protector
*2 Fuel Lid Lock Control Cable
*3 Hood Lock Control Cable
*4 Clamp



b.

for RHD:

i.
B238482

Connect the hood lock control cable assembly to install the hood lock control lever sub-assembly.


ii.
B238481

Attach the 3 claws and install the hood lock control lever sub-assembly.



Hide 53510 4.INSTALL HOOD LOCK ASSEMBLY (for LHD)

a.
B238487

Apply MP grease to the sliding areas of the lock.


b.
B238478E03
0.177,0.229 0.417,0.417 0.24,0.188 10 true *A

Connect the hood lock control cable assembly.

Text in Illustration
*A w/ Engine Hood Courtesy Switch


c.

w/ Engine Hood Courtesy Switch:

Connect the connector.


d.
B238477

Install the hood lock assembly with the 3 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 53510 5.INSTALL HOOD LOCK ASSEMBLY (for RHD)

a.
B238488

Apply MP grease to the sliding areas of the lock.


b.
B238480E02
2.313,0.583 2.583,0.75 0.271,0.167 10 true *A

Connect the hood lock control cable assembly.

Text in Illustration
*A w/ Engine Hood Courtesy Switch


c.

w/ Engine Hood Courtesy Switch:

Connect the connector.


d.
B238479

Install the hood lock assembly with the 3 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 53629 6.INSTALL HOOD LOCK CONTROL CABLE COVER

a.
B241650E03
0.029,0 0.264,0.210 0.235,0.210 10 *A 0.029,2.242 0.223,2.452 0.194,0.210 10 *B

Pass the hood lock control cable assembly through the hood lock control cable cover.

Text in Illustration
*A for LHD
*B for RHD


b.

Attach the claw to install the hood lock control cable cover.


c.

Install the 2 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 86520 7.INSTALL LOW PITCHED HORN ASSEMBLY (for LHD)

Hide 86510 8.INSTALL HIGH PITCHED HORN ASSEMBLY (for LHD)

Hide 53525 9.INSTALL HOOD LOCK RELEASE LEVER PROTECTOR

a.

Attach the 2 claws and 2 guides to install the hood lock release lever protector.


Hide 88211B 10.INSTALL MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Dynamic Radar Cruise Control System)

Hide 88211B 12.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Dynamic Radar Cruise Control System)