Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR › 2015.06–2016.08
RM27T0E _59 Vehicle Exterior _053744 DOOR / HATCH _0261248 REAR DOOR N

DOOR / HATCH  REAR DOOR  ADJUSTMENT  


CAUTION / NOTICE / HINT

B217557E01
0.264,1.555 1.177,1.725 0.913,0.170 10 Centering Bolt 2.12,1.555 3.005,1.725 0.885,0.170 10 Standard Bolt

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts when making adjustments.

·

The specified torque for standard bolts is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).



PROCEDURE

Hide 1.INSPECT REAR DOOR

a.

Check that the clearance measurements of areas A through N are within the standard range.

B237274E02
2.708,0.333 2.906,0.552 0.198,0.219 10 false A 2.854,0.688 3.052,0.906 0.198,0.219 10 false B 4.26,0.313 4.458,0.531 0.198,0.219 10 false C 4.448,0.688 4.646,0.906 0.198,0.219 10 false D 6.167,1.594 6.365,1.813 0.198,0.219 10 false E 6.385,1.813 6.583,2.031 0.198,0.219 10 false F 4.833,4.25 5.031,4.469 0.198,0.219 10 false G 5.135,3.667 5.333,3.885 0.198,0.219 10 false H 3.146,3.948 3.344,4.167 0.198,0.219 10 false I 2.896,3.333 3.146,3.552 0.25,0.219 10 false J 0.833,3.417 1.073,3.635 0.24,0.219 10 false L 1.167,2.781 1.417,3 0.25,0.219 10 false K 0.667,1.865 0.906,2.083 0.24,0.219 10 false N 1.448,1.281 1.698,1.5 0.25,0.219 10 false M

Standard:
Area Measurement Area Measurement
A 3.7 to 6.7 mm (0.146 to 0.264 in.) B 4.2 to 7.2 mm (0.165 to 0.284 in.)
C 3.6 to 6.6 mm (0.142 to 0.260 in.) D 4.9 to 7.9 mm (0.193 to 0.311 in.)
E 2.7 to 5.7 mm (0.106 to 0.224 in.) F -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
G 4.05 to 7.05 mm (0.159 to 0.278 in.) H 4.6 to 7.6 mm (0.181 to 0.299 in.)
I 4.05 to 7.05 mm (0.159 to 0.278 in.) J 4.6 to 7.6 mm (0.181 to 0.299 in.)
K 3.0 to 6.0 mm (0.118 to 0.236 in.) L -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
M 2.5 to 6.5 mm (0.0984 to 0.256 in.) N -2.0 to 2.0 mm (-0.0787 to 0.0787 in.)



Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



Hide 3.ADJUST REAR DOOR

a.
B237275

Using SST, loosen the hinge bolts on the vehicle body and adjust the door position.

SST
09812-00010  


b.

Tighten the hinge bolts on the vehicle body.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


c.

Loosen the hinge bolts on the door and adjust the door position.


d.

Tighten the hinge bolts on the door.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


e.
B237273

Using a T40 "TORX" socket wrench, slightly loosen the striker mounting screws.


f.

Using a brass bar and hammer, hit the striker to adjust its position.


g.

Using a T40 "TORX" socket wrench, tighten the striker mounting screws.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)


Hide 4.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 5.INSPECT SRS WARNING LIGHT