Home › Vehicle Exterior › MIRROR (EXT) › OUTER MIRROR SWITCH › 2015.06–2017.08
RM27T0E _59 Vehicle Exterior _053745 MIRROR (EXT) _0261252 OUTER MIRROR SWITCH G

MIRROR (EXT)  OUTER MIRROR SWITCH  INSPECTION  


PROCEDURE

Hide 84870A 1.INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/o Retract Mirror)

B231581E02
1.643,2.525 1.843,2.746 0.201,0.220 10 *a 1.63,3.504 1.399,4.054 false 1.966,3.504 1.957,4.052 false 2.141,3.516 2.406,4.064 false 1.603,4.084 1.761,4.242 0.158,0.158 10 B 3.129,3.423 3.359,3.582 0.230,0.158 10 M+ 2.994,3.779 3.349,3.937 0.355,0.158 10 MRH 2.66,4.084 3.014,4.242 0.355,0.158 10 MRV 2.253,4.084 2.607,4.242 0.355,0.158 10 MLV 1.803,4.084 2.158,4.242 0.355,0.158 10 MLH 1.339,4.088 1.475,4.239 0.136,0.151 10 E 1.798,3.51 1.669,4.057 false 2.292,3.508 2.811,4.079 false 2.459,3.5 2.964,3.867 false 2.662,3.445 3.108,3.496 false 1.152,3.507 0.678,3.933 false 0.932,3.444 0.545,3.559 false 0.339,3.885 0.635,4.100 0.297,0.214 10 ILL+ 0.23,3.47 0.527,3.684 0.297,0.214 10 ILL-

a.

Inspect the outer mirror switch.

i.

Select "L" on the left/right adjustment switch.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
9 (MLV) - 11 (B)
6 (M+) - 12 (E)
UP Pressed Below 1 Ω
Not pressed 10 kΩ or higher
9 (MLV) - 12 (E)
6 (M+) - 11 (B)
DOWN Pressed Below 1 Ω
Not pressed 10 kΩ or higher
10 (MLH) - 11 (B)
6 (M+) - 12 (E)
LEFT Pressed Below 1 Ω
Not pressed 10 kΩ or higher
10 (MLH) - 12 (E)
6 (M+) - 11 (B)
RIGHT Pressed Below 1 Ω
Not pressed 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.


iii.

Select "R" on the left/right adjustment switch.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
8 (MRV) - 11 (B)
6 (M+) - 12 (E)
UP Pressed Below 1 Ω
Not pressed 10 kΩ or higher
8 (MRV) - 12 (E)
6 (M+) - 11 (B)
DOWN Pressed Below 1 Ω
Not pressed 10 kΩ or higher
7 (MRH) - 11 (B)
6 (M+) - 12 (E)
LEFT Pressed Below 1 Ω
Not pressed 10 kΩ or higher
7 (MRH) - 12 (E)
6 (M+) - 11 (B)
RIGHT Pressed Below 1 Ω
Not pressed 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



b.

Inspect the switch illumination.

Apply battery voltage between the terminals of the light, and check the operation of the light.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 15 (ILL+)
Battery negative (-) → Terminal 16 (ILL-)
Light comes on


If the result is not as specified, replace the outer mirror switch assembly.

Text in Illustration
*a Component without harness connected
(Outer Mirror Switch Assembly)


Hide 84870A 2.INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/ Retract Mirror)

B231580E02
1.596,2.563 1.785,2.737 0.188,0.174 10 *a 1.609,3.663 1.378,4.212 false 1.449,3.674 1.164,4.213 false 1.277,3.68 0.855,4.236 false 1.945,3.662 1.936,4.21 false 2.12,3.675 2.384,4.223 false 1.582,4.242 1.740,4.400 0.158,0.158 10 B 3.108,3.582 3.322,3.740 0.214,0.158 10 M+ 2.973,3.938 3.328,4.096 0.355,0.158 10 MRH 2.638,4.242 2.993,4.400 0.355,0.158 10 MRV 2.231,4.242 2.586,4.400 0.355,0.158 10 MLV 1.782,4.242 2.136,4.400 0.355,0.158 10 MLH 1.317,4.246 1.454,4.398 0.136,0.151 10 E 1.776,3.669 1.648,4.216 false 2.27,3.667 2.79,4.238 false 2.438,3.658 2.942,4.025 false 2.64,3.604 3.087,3.654 false 1.131,3.666 0.657,4.091 false 0.911,3.603 0.524,3.717 false 0.318,4.044 0.614,4.258 0.297,0.214 10 ILL+ 0.209,3.629 0.505,3.843 0.297,0.214 10 ILL- 1.445,0.108 1.660,0.295 0.215,0.187 10 *1 1.647,0.202 2.119,0.202 2.119,0.202 2.119,0.742 false 0.963,4.253 1.230,4.436 0.267,0.184 10 MR 0.633,4.245 0.862,4.438 0.230,0.193 10 MF

a.

Inspect the outer mirror switch.

i.

Select "L" on the left/right adjustment switch.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
9 (MLV) - 11 (B)
6 (M+) - 12 (E)
UP Pressed Below 1 Ω
Not pressed 10 kΩ or higher
9 (MLV) - 12 (E)
6 (M+) - 11 (B)
DOWN Pressed Below 1 Ω
Not pressed 10 kΩ or higher
10 (MLH) - 11 (B)
6 (M+) - 12 (E)
LEFT Pressed Below 1 Ω
Not pressed 10 kΩ or higher
10 (MLH) - 12 (E)
6 (M+) - 11 (B)
RIGHT Pressed Below 1 Ω
Not pressed 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.


iii.

Select "R" on the left/right adjustment switch.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
8 (MRV) - 11 (B)
6 (M+) - 12 (E)
UP Pressed Below 1 Ω
Not pressed 10 kΩ or higher
8 (MRV) - 12 (E)
6 (M+) - 11 (B)
DOWN Pressed Below 1 Ω
Not pressed 10 kΩ or higher
7 (MRH) - 11 (B)
6 (M+) - 12 (E)
LEFT Pressed Below 1 Ω
Not pressed 10 kΩ or higher
7 (MRH) - 12 (E)
6 (M+) - 11 (B)
RIGHT Pressed Below 1 Ω
Not pressed 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



b.

Inspect the retract switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
12 (E) - 14 (MF)
11 (B) - 13 (MR)
Pushed in Below 1 Ω
12 (E) - 13 (MR)
11 (B) - 14 (MF)
Not pushed in Below 1 Ω


If the result is not as specified, replace the outer mirror switch assembly.



c.

Inspect the switch illumination.

Apply battery voltage between the terminals of the light, and check the operation of the light.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 15 (ILL+)
Battery negative (-) → Terminal 16 (ILL-)
Light comes on


If the result is not as specified, replace the outer mirror switch assembly.

Text in Illustration
*1 Retract Switch
*a Component without harness connected
(Outer Mirror Switch Assembly)