Home › Vehicle Exterior › MIRROR (EXT) › OUTER REAR VIEW MIRROR › 2015.06–2017.08
RM27T0E _59 Vehicle Exterior _053745 MIRROR (EXT) _0261253 OUTER REAR VIEW MIRROR G

MIRROR (EXT)  OUTER REAR VIEW MIRROR  INSPECTION  


PROCEDURE

Hide 87940 1.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (w/ Side Monitor System)

B242850E04
1.302,2.76 0.99,2.625 true 1.458,2.969 1.219,3.188 true 1.313,2.906 0.99,2.906 true 0.688,2.833 0.948,3.01 0.26,0.177 10 false MH 0.698,2.51 0.958,2.688 0.26,0.177 10 false MV 0.958,3.167 1.208,3.323 0.25,0.156 10 false M+ 1.604,1.865 1.813,2.042 0.208,0.177 10 false *a 1.594,0.396 1.844,0.594 0.25,0.198 10 true (A) 1.146,0.729 1.417,0.958 0.271,0.229 10 true (C) 2.094,0.708 2.333,0.927 0.24,0.219 10 true (D) 1.646,1.229 1.885,1.469 0.24,0.24 10 true (B)

a.

Apply battery voltage and check the operation of the mirror.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 1 (MV)
Battery negative (-) → Terminal 9 (M+)
Turns upward (A)
Battery negative (-) → Terminal 1 (MV)
Battery positive (+) → Terminal 9 (M+)
Turns downward (B)
Battery positive (+) → Terminal 8 (MH)
Battery negative (-) → Terminal 9 (M+)
Turns left (C)
Battery negative (-) → Terminal 8 (MH)
Battery positive (+) → Terminal 9 (M+)
Turns right (D)


If the result is not as specified, replace the outer rear view mirror assembly LH.

Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


b.
B242854E01
1.67,2.92 1.895,3.109 0.225,0.188 10 *a 0.666,3.674 0.975,3.861 0.309,0.187 10 MR 0.666,4.22 0.898,4.411 0.232,0.191 10 MF 1.65,3.902 1.571,3.771 1.571,3.771 0.95,3.771 false 1.654,4.168 1.61,4.306 1.61,4.306 0.952,4.306 false 1.589,0 1.829,0.248 0.239,0.248 10 (A) 1.188,0.926 1.428,1.175 0.239,0.248 10 (B) 1.406,2.072 1.645,2.321 0.239,0.248 10 (C) 1.87,2.336 2.109,2.584 0.239,0.248 10 (D) 2.391,2.645 2.631,2.894 0.239,0.248 10 (E)

For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.

OK:
Measurement Condition Mirror Position Specified Condition
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 10 (MF)
Forward position (A) Moves from (A) to retracted position (E)
Battery negative (-) → Terminal 3 (MR)
Battery positive (+) → Terminal 10 (MF)
Forward position (A) Does not move
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 10 (MF)
Position between forward position (A) and driving position (C) Moves from (B) to retracted position (E)
Battery negative (-) → Terminal 3 (MR)
Battery positive (+) → Terminal 10 (MF)
Position between forward position (A) and driving position (C) Moves from (B) to forward position (A)
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 10 (MF)
Driving position (C) Moves from (C) to retracted position (E)
Battery negative (-) → Terminal 3 (MR)
Battery positive (+) → Terminal 10 (MF)
Driving position (C) Does not move
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 10 (MF)
Position between driving position (C) and retracted position (E) Moves from (D) to retracted position (E)
Battery negative (-) → Terminal 3 (MR)
Battery positive (+) → Terminal 10 (MF)
Position between driving position (C) and retracted position (E) Moves from (D) to driving position (C)
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 10 (MF)
Retracted position (E) Does not move
Battery negative (-) → Terminal 3 (MR)
Battery positive (+) → Terminal 10 (MF)
Retracted position (E) Moves from (E) to driving position (C)


NOTICE:
·

Disconnect and reconnect the battery between each mirror position check.


·

Do not apply battery voltage when moving the mirror by hand into each mirror position.



If the result is not as specified, replace the outer rear view mirror assembly LH.

Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


c.
B242852E01
1.551,1.711 1.790,1.902 0.239,0.191 10 *a 1.129,1.96 1.282,2.130 0.152,0.170 10 + 1.186,3.122 1.332,3.281 0.146,0.159 10 - 1.693,2.695 1.534,2.047 1.534,2.047 1.255,2.047 false 1.699,2.954 1.529,3.226 1.529,3.226 1.297,3.226 false

w/ Mirror Heater:

Check the mirror heater.

i.

Measure the resistance according to the value (s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 4 (+) - Terminal 11 (-) 25°C (75°F) 3.0 to 3.9 Ω


If the result is not as specified, replace the outer rear view mirror assembly LH.


ii.

Apply battery voltage and check the operation of the mirror heater.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 4 (+)
Battery negative (-) → Terminal 11 (-)
Mirror becomes warm


HINT:

It will take a short time for the mirror to become warm.


If the result is not as specified, replace the outer rear view mirror assembly LH.

Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)



Hide 87910 2.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (w/ Side Monitor System)

B242849E05
1.313,2.927 1.073,3.135 true 1.302,2.75 0.885,2.75 true 1.458,2.948 1.708,3.167 true 1.625,1.74 1.875,1.917 0.25,0.177 10 false *a 1.646,1.198 1.906,1.427 0.26,0.229 10 true (B) 1.135,0.667 1.375,0.844 0.24,0.177 10 true (C) 2.073,0.698 2.313,0.896 0.24,0.198 10 true (D) 0.771,3.094 1.063,3.292 0.292,0.198 10 false MH 0.563,2.677 0.927,2.854 0.365,0.177 10 false MV 1.625,3.188 1.854,3.354 0.229,0.167 10 false M+ 1.646,0.25 1.885,0.427 0.24,0.177 10 true (A)

a.

Apply battery voltage and check the operation of the mirror.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 1 (MV)
Battery negative (-) → Terminal 9 (M+)
Turns upward (A)
Battery negative (-) → Terminal 1 (MV)
Battery positive (+) → Terminal 9 (M+)
Turns downward (B)
Battery positive (+) → Terminal 8 (MH)
Battery negative (-) → Terminal 9 (M+)
Turns left (C)
Battery negative (-) → Terminal 8 (MH)
Battery positive (+) → Terminal 9 (M+)
Turns right (D)


If the result is not as specified, replace the outer rear view mirror assembly RH.

Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


b.
B242853E01
1.533,2.8 1.759,2.988 0.225,0.188 10 *a 0.577,3.581 0.885,3.768 0.309,0.187 10 MR 0.564,4.307 0.796,4.498 0.232,0.191 10 MF 1.578,3.91 1.498,3.661 1.498,3.661 0.877,3.661 false 1.578,4.157 1.531,4.4 1.531,4.4 0.835,4.4 false 1.658,0 1.897,0.248 0.239,0.248 10 (A) 2.045,0.982 2.284,1.231 0.239,0.248 10 (B) 1.836,1.959 2.075,2.208 0.239,0.248 10 (C) 1.364,2.323 1.604,2.571 0.239,0.248 10 (D) 0.836,2.549 1.075,2.798 0.239,0.248 10 (E)

For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.

OK:
Measurement Condition Mirror Position Specified Condition
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 10 (MF)
Forward position (A) Moves from (A) to retracted position (E)
Battery negative (-) → Terminal 3 (MR)
Battery positive (+) → Terminal 10 (MF)
Forward position (A) Does not move
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 10 (MF)
Position between forward position (A) and driving position (C) Moves from (B) to retracted position (E)
Battery negative (-) → Terminal 3 (MR)
Battery positive (+) → Terminal 10 (MF)
Position between forward position (A) and driving position (C) Moves from (B) to forward position (A)
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 10 (MF)
Driving position (C) Moves from (C) to retracted position (E)
Battery negative (-) → Terminal 3 (MR)
Battery positive (+) → Terminal 10 (MF)
Driving position (C) Does not move
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 10 (MF)
Position between driving position (C) and retracted position (E) Moves from (D) to retracted position (E)
Battery negative (-) → Terminal 3 (MR)
Battery positive (+) → Terminal 10 (MF)
Position between driving position (C) and retracted position (E) Moves from (D) to driving position (C)
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 10 (MF)
Retracted position (E) Does not move
Battery negative (-) → Terminal 3 (MR)
Battery positive (+) → Terminal 10 (MF)
Retracted position (E) Moves from (E) to driving position (C)


NOTICE:
·

Disconnect and reconnect the battery between each mirror position check.


·

Do not apply battery voltage when moving the mirror by hand into each mirror position.



If the result is not as specified, replace the outer rear view mirror assembly RH.

Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


c.
B242851E01
1.629,1.722 1.951,2.065 0.323,0.343 10 *a 1.126,1.931 1.279,2.101 0.152,0.170 10 + 1.177,3.087 1.286,3.288 0.109,0.201 10 - 1.693,2.64 1.534,2.018 1.534,2.018 1.255,2.018 false 1.693,2.899 1.523,3.191 1.523,3.191 1.291,3.191 false

w/ Mirror Heater:

Check the mirror heater.

i.

Measure the resistance according to the value (s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 4 (+) - Terminal 11 (-) 25°C (75°F) 3.0 to 3.9 Ω


If the result is not as specified, replace the outer rear view mirror assembly RH.


ii.

Apply battery voltage and check the operation of the mirror heater.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 4 (+)
Battery negative (-) → Terminal 11 (-)
Mirror becomes warm


HINT:

It will take a short time for the mirror to become warm.


If the result is not as specified, replace the outer rear view mirror assembly RH.

Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)



Hide 87940 3.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (w/o Side Monitor System)

B199929E08
1.865,2.677 2.135,1.917 2.135,1.917 2.552,1.917 true 1.969,2.677 2.271,2.229 2.271,2.229 2.542,2.229 true 2.094,2.667 2.375,2.521 2.375,2.521 2.531,2.521 true 1.625,1.719 1.875,1.896 0.25,0.177 10 false *a 2.563,2.438 2.792,2.583 0.229,0.146 10 false MV 1.677,1.271 1.906,1.49 0.229,0.219 10 true (B) 1.208,0.813 1.438,1.01 0.229,0.198 10 true (C) 1.604,0.344 1.854,0.521 0.25,0.177 10 false (A) 2.115,0.771 2.354,0.99 0.24,0.219 10 true (D) 2.563,2.146 2.792,2.292 0.229,0.146 10 false M+ 2.563,1.833 2.833,1.979 0.271,0.146 10 false MH

a.

Apply battery voltage and check the operation of the mirror.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 6 (MV)
Battery negative (-) → Terminal 5 (M+)
Turns upward (A)
Battery negative (-) → Terminal 6 (MV)
Battery positive (+) → Terminal 5 (M+)
Turns downward (B)
Battery positive (+) → Terminal 4 (MH)
Battery negative (-) → Terminal 5 (M+)
Turns left (C)
Battery negative (-) → Terminal 4 (MH)
Battery positive (+) → Terminal 5 (M+)
Turns right (D)


If the result is not as specified, replace the outer rear view mirror assembly LH.

Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


b.
B199933E01
0.89,2.056 1.115,2.244 0.225,0.188 10 *a 0.582,2.475 0.891,2.662 0.309,0.187 10 MR 0.578,2.935 0.810,3.126 0.232,0.191 10 MF 1.564,2.708 1.486,2.574 1.486,2.574 0.878,2.574 false 1.567,2.92 1.524,3.043 1.524,3.043 0.878,3.043 false 1.148,0 1.387,0.248 0.239,0.248 10 (A) 0.861,0.761 1.101,1.010 0.239,0.248 10 (B) 0.982,1.535 1.221,1.783 0.239,0.248 10 (C) 1.4,1.792 1.639,2.041 0.239,0.248 10 (D) 1.761,1.981 2.000,2.230 0.239,0.248 10 (E)

w/ Retract Mirror:

For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.

OK:
Measurement Condition Mirror Position Specified Condition
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 9 (MF)
Forward position (A) Moves from (A) to retracted position (E)
Battery negative (-) → Terminal 3 (MR)
Battery positive (+) → Terminal 9 (MF)
Forward position (A) Does not move
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 9 (MF)
Position between forward position (A) and driving position (C) Moves from (B) to retracted position (E)
Battery negative (-) → Terminal 3 (MR)
Battery positive (+) → Terminal 9 (MF)
Position between forward position (A) and driving position (C) Moves from (B) to forward position (A)
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 9 (MF)
Driving position (C) Moves from (C) to retracted position (E)
Battery negative (-) → Terminal 3 (MR)
Battery positive (+) → Terminal 9 (MF)
Driving position (C) Does not move
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 9 (MF)
Position between driving position (C) and retracted position (E) Moves from (D) to retracted position (E)
Battery negative (-) → Terminal 3 (MR)
Battery positive (+) → Terminal 9 (MF)
Position between driving position (C) and retracted position (E) Moves from (D) to driving position (C)
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 9 (MF)
Retracted position (E) Does not move
Battery negative (-) → Terminal 3 (MR)
Battery positive (+) → Terminal 9 (MF)
Retracted position (E) Moves from (E) to driving position (C)


NOTICE:
·

Disconnect and reconnect the battery between each mirror position check.


·

Do not apply battery voltage when moving the mirror by hand into each mirror position.



If the result is not as specified, replace the outer rear view mirror assembly LH.

Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


c.
B242855E01
1.472,1.764 1.795,2.107 0.323,0.343 10 *a 0.791,2.401 0.944,2.571 0.152,0.170 10 + 0.791,3.041 0.900,3.242 0.109,0.201 10 - 1.379,2.652 1.212,2.494 1.212,2.494 0.92,2.494 false 1.375,2.885 1.183,3.137 1.183,3.137 0.92,3.137 false

w/ Mirror heater:

Check the mirror heater.

i.

Measure the resistance according to the value (s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 2 (+) - Terminal 8 (-) 25°C (75°F) 3.0 to 3.9 Ω


If the result is not as specified, replace the outer rear view mirror assembly LH.


ii.

Apply battery voltage and check the operation of the mirror heater.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 2 (+)
Battery negative (-) → Terminal 8 (-)
Mirror becomes warm


HINT:

It will take a short time for the mirror to become warm.


If the result is not as specified, replace the outer rear view mirror assembly LH.

Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)



Hide 87910 4.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (w/o Side Monitor System)

B199928E09
1.885,2.667 2.156,1.958 2.156,1.958 2.552,1.958 true 1.979,2.677 2.281,2.271 2.281,2.271 2.542,2.271 true 2.094,2.667 2.396,2.594 2.396,2.594 2.573,2.594 true 1.646,1.177 1.896,1.396 0.25,0.219 10 true (B) 1.188,0.667 1.417,0.885 0.229,0.219 10 true (C) 1.667,0.25 1.938,0.427 0.271,0.177 10 false (A) 2.063,0.708 2.292,0.948 0.229,0.24 10 true (D) 1.635,1.802 1.885,1.979 0.25,0.177 10 false *a 2.573,2.521 2.802,2.667 0.229,0.146 10 false MV 2.573,2.177 2.802,2.323 0.229,0.146 10 false M+ 2.573,1.865 2.844,2.01 0.271,0.146 10 false MH

a.

Apply battery voltage and check the operation of the mirror.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 6 (MV)
Battery negative (-) → Terminal 5 (M+)
Turns upward (A)
Battery negative (-) → Terminal 6 (MV)
Battery positive (+) → Terminal 5 (M+)
Turns downward (B)
Battery positive (+) → Terminal 4 (MH)
Battery negative (-) → Terminal 5 (M+)
Turns left (C)
Battery negative (-) → Terminal 4 (MH)
Battery positive (+) → Terminal 5 (M+)
Turns right (D)


If the result is not as specified, replace the outer rear view mirror assembly RH.

Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


b.
B199932E01
0.765,2.046 0.990,2.234 0.225,0.188 10 *a 0.584,2.5 0.893,2.687 0.309,0.187 10 MR 0.584,3.016 0.817,3.206 0.232,0.191 10 MF 1.563,2.704 1.488,2.577 1.488,2.577 0.904,2.577 false 1.558,2.934 1.517,3.123 1.517,3.123 0.904,3.123 false 2.037,0 2.276,0.248 0.239,0.248 10 (A) 2.352,0.742 2.591,0.991 0.239,0.248 10 (B) 2.176,1.604 2.415,1.852 0.239,0.248 10 (C) 1.763,1.87 2.002,2.118 0.239,0.248 10 (D) 1.339,2.054 1.578,2.303 0.239,0.248 10 (E)

w/ Retract Mirror:

For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.

OK:
Measurement Condition Mirror Position Specified Condition
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 9 (MF)
Forward position (A) Moves from (A) to retracted position (E)
Battery negative (-) → Terminal 3 (MR)
Battery positive (+) → Terminal 9 (MF)
Forward position (A) Does not move
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 9 (MF)
Position between forward position (A) and driving position (C) Moves from (B) to retracted position (E)
Battery negative (-) → Terminal 3 (MR)
Battery positive (+) → Terminal 9 (MF)
Position between forward position (A) and driving position (C) Moves from (B) to forward position (A)
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 9 (MF)
Driving position (C) Moves from (C) to retracted position (E)
Battery negative (-) → Terminal 3 (MR)
Battery positive (+) → Terminal 9 (MF)
Driving position (C) Does not move
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 9 (MF)
Position between driving position (C) and retracted position (E) Moves from (D) to retracted position (E)
Battery negative (-) → Terminal 3 (MR)
Battery positive (+) → Terminal 9 (MF)
Position between driving position (C) and retracted position (E) Moves from (D) to driving position (C)
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 9 (MF)
Retracted position (E) Does not move
Battery negative (-) → Terminal 3 (MR)
Battery positive (+) → Terminal 9 (MF)
Retracted position (E) Moves from (E) to driving position (C)


NOTICE:
·

Disconnect and reconnect the battery between each mirror position check.


·

Do not apply battery voltage when moving the mirror by hand into each mirror position.



If the result is not as specified, replace the outer rear view mirror assembly RH.

Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


c.
B242856E01
1.502,1.722 1.825,2.066 0.323,0.343 10 *a 0.833,2.271 0.985,2.441 0.152,0.170 10 + 0.861,2.988 0.970,3.189 0.109,0.201 10 - 1.397,2.596 1.238,2.366 1.238,2.366 0.959,2.366 false 1.399,2.829 1.213,3.097 1.213,3.097 0.959,3.097 false

w/ Mirror Heater:

Check the mirror heater.

i.

Measure the resistance according to the value (s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 2 (+) - Terminal 8 (-) 25°C (75°F) 3.0 to 3.9 Ω


If the result is not as specified, replace the outer rear view mirror assembly RH.


ii.

Apply battery voltage and check the operation of the mirror heater.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 2 (+)
Battery negative (-) → Terminal 8 (-)
Mirror becomes warm


HINT:

It will take a short time for the mirror to become warm.


If the result is not as specified, replace the outer rear view mirror assembly RH.

Text in Illustration
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)