Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM › 2015.06–2017.08
RM27T0E _59 Vehicle Exterior _053746 WIPER / WASHER _0261257 WIPER AND WASHER SYSTEM J

WIPER / WASHER  WIPER AND WASHER SYSTEM  Headlight Cleaner Motor and Relay Circuit  


DESCRIPTION

This circuit provides power to the headlight cleaner control relay.

The headlight cleaner control relay sends the signal from the headlight cleaner switch assembly, etc. to the headlight cleaner motor and pump assembly to operate the headlight cleaner system.

WIRING DIAGRAM

B246535E05
5.063,3.094 7.104,3.448 2.042,0.354 10 false Headlight Cleaner Control Relay 3.427,1.021 5,1.563 1.573,0.542 10 false Headlight Cleaner Motor and Pump Assembly 2.01,0.677 2.729,0.844 0.719,0.167 10 false H-LP CLN 1.896,2.146 2.833,2.313 0.938,0.167 10 false ECU-IG NO.2 0.448,0.49 1.281,0.656 0.833,0.167 10 false form Battery 0.292,1.948 1.281,2.313 0.99,0.365 10 false form IG1 NO.1 Relay 5.656,0.49 5.896,0.646 0.24,0.156 10 false PB 5.458,0.375 5.573,0.531 0.115,0.156 10 false 6 5.458,1.844 5.573,2 0.115,0.156 10 false 3 5.458,2.292 5.573,2.448 0.115,0.156 10 false 4 5.656,1.958 5.896,2.115 0.24,0.156 10 false IG 5.656,2.396 5.771,2.552 0.115,0.156 10 false E 4.656,0.375 4.771,0.531 0.115,0.156 10 false 1 3.625,0.375 3.74,0.531 0.115,0.156 10 false 2 3.438,0.896 3.896,1.094 0.458,0.198 10 false A37 5.063,2.938 5.521,3.135 0.458,0.198 10 false A38

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (HEADLIGHT CLEANER OPERATION)
a.

Using the intelligent tester, perform the Active Test (See page Vehicle Exterior>WIPER / WASHER>WIPER AND WASHER SYSTEM>DATA LIST / ACTIVE TEST).

Main Body
Tester Display Test Part Control Range Diagnostic Note
Head Light Cleaner Headlight cleaner operation ON/OFF -

HINT:

The headlight cleaner system only operates when the front wiper washer switch (windshield wiper switch) is turned on the first time. After that, the headlight cleaner system cannot be operated with the front wiper washer switch (windshield wiper switch) until the ignition switch is turned off and then turned to ON.


OK:

Headlight cleaner operates.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT HEADLIGHT CLEANER MOTOR AND PUMP ASSEMBLY
2.INSPECT HEADLIGHT CLEANER MOTOR AND PUMP ASSEMBLY
a.
E196856

Remove the headlight cleaner motor (See page Vehicle Exterior>WIPER / WASHER>HEADLIGHT CLEANER MOTOR>REMOVAL).


b.

Apply battery voltage to the headlight cleaner motor and check the operation of the headlight cleaner motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 2
Battery negative (-) → 1
Headlight cleaner motor operation is normal




OK

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT CLEANER MOTOR AND PUMP ASSEMBLY - BATTERY)

NG

REPLACE HEADLIGHT CLEANER MOTOR AND PUMP ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT CLEANER MOTOR AND PUMP ASSEMBLY - BATTERY)
a.
U170629E01
0.189,0.043 0.382,0.203 0.193,0.161 10 *a 0.453,0.948 0.727,1.108 0.274,0.161 10 A37

Disconnect the A37 headlight cleaner motor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A37-2 - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Headlight Cleaner Motor and Pump Assembly)



OK

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT CLEANER CONTROL RELAY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT CLEANER CONTROL RELAY - BATTERY AND BODY GROUND)
a.
U170626E01
0.177,0.068 0.338,0.233 0.161,0.165 10 *a 2.003,1.027 2.341,0.69 2.341,0.69 2.426,0.69 false 2.443,0.607 2.618,0.758 0.175,0.151 10 IG 1.761,1.698 1.901,1.850 0.140,0.151 10 E 1.505,1.299 1.616,1.792 1.616,1.792 1.737,1.792 false 0.501,1.056 0.794,1.203 0.292,0.147 10 A38

Disconnect the A38 headlight cleaner control relay connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A38-3 (IG) - Body ground Ignition switch ON 11 to 14 V
A38-3 (IG) - Body ground Ignition switch off Below 1 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A38-4 (E) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Headlight Cleaner Control Relay)


OK

5.CHECK HARNESS AND CONNECTOR (HEADLIGHT CLEANER MOTOR AND PUMP ASSEMBLY - HEADLIGHT CLEANER CONTROL RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (HEADLIGHT CLEANER MOTOR AND PUMP ASSEMBLY - HEADLIGHT CLEANER CONTROL RELAY)
a.

Disconnect the A38 headlight cleaner control relay connector.


b.

Disconnect the A37 headlight cleaner motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A37-1 - A38-6 (PB) Always Below 1 Ω
A38-6 (PB) - Body ground Always 10 kΩ or higher




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR