Home › Vehicle Exterior › WIPER / WASHER › FRONT WIPER MOTOR
RM27T0E _59 Vehicle Exterior _053746 WIPER / WASHER _0261258 FRONT WIPER MOTOR G

WIPER / WASHER  FRONT WIPER MOTOR  INSPECTION  


PROCEDURE

Hide 85110 1.INSPECT FRONT WIPER MOTOR AND LINK ASSEMBLY (for LHD)

a.

Place matchmarks on the motor shaft and housing.


b.
E184712E09
0.092,0 0.285,0.190 0.193,0.190 10 *a 2.46,0.141 2.654,0.331 0.193,0.190 10 +1 1.146,1.432 1.340,1.622 0.193,0.190 10 E 2.528,0.355 2.024,0.864 false 1.561,1.165 1.319,1.464 false

Check the LO operation.

i.

Connect the positive (+) lead of the battery to terminal 1 (+1) and the negative (-) lead to terminal 5 (E), and then check that the motor operates at low speed (LO).

OK:

The motor operates at low speed (LO).


Text in Illustration
*a Component without harness connected
(Windshield Wiper Motor and Link Assembly (for LHD))



c.
E184712E10
0.092,0 0.285,0.190 0.193,0.190 10 *a 2.291,1.418 2.485,1.609 0.193,0.190 10 +2 1.146,1.432 1.340,1.622 0.193,0.190 10 E 1.887,1.177 2.191,1.489 false 1.561,1.165 1.319,1.464 false

Check the HI operation.

i.

Connect the positive (+) lead of the battery to terminal 4 (+2) and the negative (-) lead to terminal 5 (E), and then check that the motor operates at high speed (HI).

OK:

The motor operates at high speed (HI).


Text in Illustration
*a Component without harness connected
(Windshield Wiper Motor and Link Assembly (for LHD))



d.
E184712E11
0.951,0.141 1.144,0.331 0.193,0.190 10 S 0.092,0 0.285,0.190 0.193,0.190 10 *a 1.673,0.136 1.867,0.327 0.193,0.190 10 B 2.568,0.154 2.761,0.344 0.193,0.190 10 +1 1.146,1.432 1.340,1.622 0.193,0.190 10 E 1.086,0.33 1.428,0.884 false 2.528,0.355 2.024,0.864 false 1.734,0.323 1.734,0.852 false 1.561,1.165 1.319,1.464 false

Check the automatic stop operation.

i.

Connect the positive (+) lead of the battery to terminal 1 (+1) and the negative (-) lead to terminal 5 (E). With the motor operating at low speed (LO), disconnect terminal 1 (+1) to stop the wiper motor operation at any position other than the automatic stop position.


ii.

Using SST, connect terminals 3 (S) and 1 (+1). Then connect the positive (+) lead of the battery to terminal 2 (B) and the negative (-) lead to terminal 5 (E) to restart the motor operation at low speed (LO).

SST
09843-18040  


iii.

Check that the motor stops automatically at the position where the matchmarks align.

OK:

The motor stops automatically at the position where the matchmarks align.


If the result is not as specified, replace the front motor and link assembly.

Text in Illustration
*a Component without harness connected
(Windshield Wiper Motor and Link Assembly (for LHD))



Hide 85110 2.INSPECT FRONT WIPER MOTOR AND LINK ASSEMBLY (for RHD)

a.

Place matchmarks on the motor shaft and housing.


b.
E184712E15
0.092,0 0.285,0.190 0.193,0.190 10 *a 0.986,1.548 1.179,1.738 0.193,0.190 10 +1 2.334,1.548 2.527,1.738 0.193,0.190 10 E 1.887,1.177 2.191,1.489 false 1.561,1.165 1.319,1.464 false

Check the LO operation.

i.

Connect the positive (+) lead of the battery to terminal 5 (+1) and the negative (-) lead to terminal 4 (E), and then check that the motor operates at low speed (LO).

OK:

The motor operates at low speed (LO).


Text in Illustration
*a Component without harness connected
(Windshield Wiper Motor and Link Assembly (for RHD))



c.
E184712E16
0.092,0 0.285,0.190 0.193,0.190 10 *a 0.801,0.136 0.995,0.327 0.193,0.190 10 +2 2.334,1.548 2.527,1.738 0.193,0.190 10 E 1.086,0.33 1.428,0.884 false 1.887,1.177 2.191,1.489 false

Check the HI operation.

i.

Connect the positive (+) lead of the battery to terminal 3 (+2) and the negative (-) lead to terminal 4 (E), and then check that the motor operates at high speed (HI).

OK:

The motor operates at high speed (HI).


Text in Illustration
*a Component without harness connected
(Windshield Wiper Motor and Link Assembly (for RHD))



d.
E184712E17
2.589,0.136 2.783,0.327 0.193,0.190 10 S 0.092,0 0.285,0.190 0.193,0.190 10 *a 1.673,0.136 1.867,0.327 0.193,0.190 10 B 0.986,1.548 1.179,1.738 0.193,0.190 10 +1 2.334,1.548 2.527,1.738 0.193,0.190 10 E 2.528,0.355 2.024,0.864 false 1.887,1.177 2.191,1.489 false 1.734,0.323 1.734,0.852 false 1.561,1.165 1.319,1.464 false

Check the automatic stop operation.

i.

Connect the positive (+) lead of the battery to terminal 5 (+1) and the negative (-) lead to terminal 4 (E). With the motor operating at low speed (LO), disconnect terminal 5 (+1) to stop the wiper motor operation at any position other than the automatic stop position.


ii.

Using SST, connect terminals 1 (S) and 5 (+1). Then connect the positive (+) lead of the battery to terminal 2 (B) and the negative (-) lead to terminal 4 (E) to restart the motor operation at low speed (LO).

SST
09843-18040  


iii.

Check that the motor stops automatically at the position where the matchmarks align.

OK:

The motor stops automatically at the position where the matchmarks align.


If the result is not as specified, replace the front wiper motor and link assembly.

Text in Illustration
*a Component without harness connected
(Windshield Wiper Motor and Link Assembly (for RHD))