Home › Vehicle Exterior › WIPER / WASHER › REAR WIPER RUBBER
RM27T0E _59 Vehicle Exterior _053746 WIPER / WASHER _0261261 REAR WIPER RUBBER A

WIPER / WASHER  REAR WIPER RUBBER  REPLACEMENT  


PROCEDURE

Hide 85242 1.REMOVE REAR WIPER BLADE

a.
E197703E03
1.583,0.635 1.583,0.375 false 2.958,1.771 2.76,1.771 false 3,1.698 3.229,1.927 0.229,0.229 10 false *1 1.49,0.677 1.719,0.906 0.229,0.229 10 false *1

Apply protective tape to the areas shown in the illustration.

Text in Illustration
*1 Protective Tape


b.

Turn the ignition switch to ON.


c.

Turn the rear wiper switch on.

HINT:

The wiper motor does not operate if the back door and back door glass are not closed.



d.

w/ Back Door Tire Carrier:

i.
B449818E01
1.365,1.719 1.51,1.896 0.146,0.177 10 true A 1.115,1.354 1.24,1.531 0.125,0.177 10 true B 1.292,2.635 1.448,2.813 0.156,0.177 10 true C 1.115,3.063 1.271,3.24 0.156,0.177 10 true D

Turn the ignition switch off when the wiper arm stops at the position shown in the illustration.

Standard Clearance:
Area Specified Condition
A - B Approximately
27° to 39°
C - D Approximately
200 to 273 mm (7.87 to 10.8 in.)


HINT:
·

It is easier to stop the wiper blade at the position indicated in the illustration while the wiper blade is returning to the original position.

·

Make sure that the end of the wiper blade stops between the third and the fifth defogger wire as counted from the bottom.





e.

w/o Back Door Tire Carrier:

i.
E199700E01
1.566,1.752 1.752,1.958 0.186,0.206 10 A 2.381,1.674 2.567,1.880 0.186,0.206 10 B 1.515,2.709 1.701,2.915 0.186,0.206 10 C 2.433,2.709 2.619,2.915 0.186,0.206 10 D

Turn the ignition switch off when the wiper arm stops at the position shown in the illustration.

Standard Clearance:
Area Measurement
A - B Approximately
23° to 43°
C - D approximately
170.4 to 304.9 mm (6.71 to 12.0 in.)




f.
E197705E01
2.169,1.167 2.388,1.370 0.219,0.203 10 *1 2.263,0.466 2.263,1.129 false

Raise the rear wiper arm.

Text in Illustration
*1 Protective Tape

NOTICE:
·

Make sure that the wiper arm does not interfere with the rear spoiler.

·

If the wiper arm does interfere with the rear spoiler, operate the engine switch again to stop the wiper arm in a near-vertical position.




g.
E197706

Raise the wiper blade to the position where the claw detaches with a click sound as shown in the illustration.

NOTICE:

Be careful not to damage the claw.



h.
E197707

Pull the wiper blade straight toward the left side of the vehicle to remove it from the wiper arm.

NOTICE:

Do not lower the wiper arm with the wiper blade removed. The arm tip may damage the back door glass surface.



Hide 85214R 2.REMOVE REAR WIPER RUBBER

a.
E186947E02
1.89,1.593 2.101,1.735 0.211,0.142 10 *1 2.364,1.542 2.206,1.682 2.206,1.682 2.063,1.682 false 2.273,0.365 2.596,0.586 0.323,0.221 10 *a 1.081,0.327 1.404,0.548 0.323,0.221 10 *a 2.597,0.958 2.920,1.179 0.323,0.221 10 *b 2.734,1.479 3.057,1.699 0.323,0.221 10 *c

Lift and pull the end of the wiper rubber protrusion from the blade stopper as shown in the illustration.

Text in Illustration
*1 Stopper
(Rear End of Blade)
*a Lightly Push
(Grip)
*b Lift
*c Pull

NOTICE:

Do not forcibly pull out the wiper rubber. The backing plates will be deformed or the blade claws will be damaged.


HINT:

Lightly pushing the rubber in the middle will allow it to be removed more easily.



b.

Remove the rear wiper rubber backing plates.


Hide 85214R 3.INSTALL REAR WIPER RUBBER

a.
E158041E05
0.748,2.458 1.197,2.861 1.197,2.861 1.414,2.861 false 3.315,1.521 3.315,0.056 3.315,0.056 1.682,0.056 false 2.358,1.119 2.358,0.056 false 1.389,0 1.648,0.273 0.260,0.273 10 *1 1.389,0.607 1.648,0.881 0.260,0.273 10 *a 1.477,2.784 1.737,2.974 0.260,0.190 10 *2 1.35,0.718 1.172,0.718 1.172,0.718 1.143,0.92 false

Install the rear wiper rubber backing plates as shown in the illustration.

Text in Illustration
*1 Rear Wiper Rubber Backing Plate
*2 Rear Wiper Rubber
*a Curve

NOTICE:

Install the backing plates facing the correct direction.



b.

Insert the wiper rubber from the front end of the wiper blade to the rear end through the second claw.


c.
E163699E11
2.5,1.813 2.594,1.813 2.594,1.813 2.646,1.313 false 2.198,1.458 2.375,1.458 2.375,1.458 2.542,1.146 false 1.5,0.156 1.448,0.156 1.448,0.156 0.927,1.083 false 1.531,0.094 1.729,0.302 0.198,0.208 10 false *1 1.99,1.375 2.177,1.531 0.188,0.156 10 true *2 2.292,1.719 2.5,1.906 0.208,0.188 10 false *3

After pushing the wiper rubber through the rear end claw, allow it to stick out from the rear end stopper.

Text in Illustration
*1 Second Claw
*2 Rear End Claw
*3 Rear End Stopper


d.
E163700E03
1.082,0.172 1.267,0.321 0.185,0.149 10 *1 1.251,0.264 1.411,0.264 1.411,0.264 1.608,0.424 false

Slide the wiper rubber through the front end claw.

Text in Illustration
*1 Front End Claw


Hide 85242 4.INSTALL REAR WIPER BLADE

a.
E202485

Push the wiper blade straight toward the right side of the vehicle to install it to the wiper arm.

NOTICE:

Make sure that the wiper arm does not interfere with the rear spoiler.



b.
E197706

attach the claw to install the rear wiper blade as shown in the illustration.

NOTICE:

Be careful not to damage the claw.