Home › Vehicle Exterior › WIPER / WASHER › WIPER SWITCH › 2015.06–2017.08
RM27T0E _59 Vehicle Exterior _053746 WIPER / WASHER _0261262 WIPER SWITCH G

WIPER / WASHER  WIPER SWITCH  INSPECTION  


PROCEDURE

Hide 84650 1.INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY (w/ Rain Sensor)

a.

for LHD Windshield Wiper Switch and RHD Windshield Wiper Switch RH Side Type:

i.
E182610E03
2.839,1.076 3.098,1.233 0.259,0.157 10 EW 0.123,0.079 0.299,0.236 0.176,0.157 10 *a 2.856,1.563 3.161,1.720 0.305,0.157 10 +1R 2.335,1.912 2.594,2.069 0.259,0.157 10 WR 1.716,1.912 2.021,2.069 0.305,0.157 10 C1R 2.438,1.242 2.793,1.173 false 2.449,1.527 2.805,1.631 false 2.197,1.563 2.361,1.886 false 2.016,1.613 1.961,1.889 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Rear Wiper Switch
Tester Connection Switch Condition Specified Condition
12 (C1R) - 1 (EW) OFF 10 kΩ or higher
10 (+1R) - 1 (EW)
12 (C1R) - 1 (EW) LO Below 1 Ω
10 (+1R) - 1 (EW) HI Below 1 Ω

Rear Washer Switch
Tester Connection Switch Condition Specified Condition
11 (WR) - 1 (EW) OFF 10 kΩ or higher
10 (+1R) - 1 (EW)
11 (WR) - 1 (EW) WASH Below 1 Ω
11 (WR) - 1 (EW) ON + WASH Below 1 Ω
10 (+1R) - 1 (EW)


Text in Illustration
*a Component without harness connected
(Windshield Wiper Switch Assembly)

If the result is not as specified, replace the windshield wiper switch assembly.



b.

for RHD Windshield Wiper Switch LH Side Type:

i.
E182610E04
0.433,0.995 0.692,1.152 0.259,0.157 10 EW 0.106,0.062 0.282,0.219 0.176,0.157 10 *a 0.381,1.601 0.686,1.758 0.305,0.157 10 +1R 1.011,1.895 1.270,2.052 0.259,0.157 10 WR 1.487,1.895 1.792,2.052 0.305,0.157 10 C1R 0.738,1.67 1.103,1.542 false 0.743,1.093 1.098,1.198 false 1.531,1.615 1.624,1.873 false 1.297,1.554 1.203,1.879 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Rear Wiper Switch
Tester Connection Switch Condition Specified Condition
16 (C1R) - 9 (EW) OFF 10 kΩ or higher
18 (+1R) - 9 (EW)
16 (C1R) - 9 (EW) LO Below 1 Ω
18 (+1R) - 9 (EW) HI Below 1 Ω

Rear Washer Switch
Tester Connection Switch Condition Specified Condition
17 (WR) - 9 (EW) OFF 10 kΩ or higher
18 (+1R) - 9 (EW)
17 (WR) - 9 (EW) WASH Below 1 Ω
17 (WR) - 9 (EW) ON + WASH Below 1 Ω
18 (+1R) - 9 (EW)


Text in Illustration
*a Component without harness connected
(Windshield Wiper Switch Assembly)

If the result is not as specified, replace the windshield wiper switch assembly.



Hide 84650 2.INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY (w/o Rain Sensor)

a.

for LHD Windshield Wiper Switch and RHD Windshield Wiper Switch RH Side Type:

i.
U149221E01
0.071,0.027 0.268,0.211 0.198,0.184 10 *a 0.34,1.185 0.641,1.347 0.301,0.163 10 A 0.404,0.737 0.611,0.900 0.208,0.163 10 +2 0.752,0.474 0.959,0.637 0.208,0.163 10 +1 1.289,0.474 1.497,0.637 0.208,0.163 10 +B 1.683,0.474 1.891,0.637 0.208,0.163 10 +S 2.315,1.892 2.627,2.055 0.313,0.163 10 C1R 1.868,1.892 2.180,2.055 0.313,0.163 10 +1R 1.392,1.892 1.659,2.055 0.266,0.163 10 WR 2.119,0.474 2.390,0.637 0.271,0.163 10 WF 2.64,0.474 2.911,0.637 0.271,0.163 10 EW 2.992,1.185 3.291,1.347 0.299,0.163 10 B 2.282,1.075 2.627,0.655 false 2.078,1.079 2.207,0.655 false 1.171,1.08 0.901,0.655 false 1.431,1.076 1.431,0.655 false 1.623,1.086 1.76,0.655 false 0.951,1.107 0.635,0.851 false 2.204,1.387 2.481,1.87 false 2.074,1.413 2.074,1.875 false 1.628,1.421 1.536,1.867 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Front Wiper Switch
Tester Connection Switch Condition Specified Condition
A-1 (+S) - A-3 (+1) OFF Below 1 Ω
INT
A-2 (+B) - A-3 (+1) MIST
LO
A-2 (+B) - A-4 (+2) HI

Front Washer Switch:
Tester Connection Switch Condition Specified Condition
B-2 (EW) - B-3 (WF) ON Below 1 Ω
OFF 10 kΩ or higher

Rear Wiper Switch:
Tester Connection Switch Condition Specified Condition
B-6 (C1R) - B-2 (EW) OFF 10 kΩ or higher
B-7 (+1R) - B-2 (EW)
B-6 (C1R) - B-2 (EW) INT Below 1 Ω
B-7 (+1R) - B-2 (EW) HI Below 1 Ω

Rear Washer Switch:
Tester Connection Switch Condition Specified Condition
A-5 (WR) - B-2 (EW) OFF 10 kΩ or higher
B-7 (+1R) - B-2 (EW)
A-5 (WR) - B-2 (EW) WASH Below 1 Ω
A-5 (WR) - B-2 (EW) ON + WASH Below 1 Ω
B-7 (+1R) - B-2 (EW)


If the result is not as specified, replace the windshield wiper switch assembly.

Text in Illustration
*a Component without harness connected
(Windshield Wiper Switch Assembly)


ii.

Check the intermittent operation.

1.

Connect the positive (+) lead of a voltmeter to terminal A-3 (+1) and the negative (-) lead to terminal B-2 (EW).

2.

Connect the battery positive (+) lead of the battery to terminal A-2 (+B) and the negative (-) lead to terminal B-2 (EW) and A-1 (+S).

3.

Turn the wiper switch to the INT position.

4.

Connect the positive (+) lead of the battery to terminal A-1 (+S) for 5 seconds.

5.

Connect the negative (-) lead of the battery to terminal A-1 (+S). Operate the intermittent wiper relay and check the voltage between terminals A-3 (+1) and B-2 (EW).

OK:

The voltage changes as shown in the illustration.


E056399E59
0.133,0.084 0.337,0.254 0.205,0.170 10 *1 1.734,0.549 2.453,0.700 0.719,0.151 10 10 to 14 V 2.2,1.028 2.474,1.184 0.274,0.156 10 0 V 2.484,1.463 3.642,1.627 1.158,0.164 10 1.6 +/- 1 second 2.699,0.205 2.896,0.366 0.197,0.161 10 *2 4.741,0.205 4.933,0.374 0.192,0.170 10 *3 4.625,1.454 5.884,1.610 1.259,0.155 10 10.7 +/- 5 seconds

If the result is not as specified, replace the windshield wiper switch assembly.

Text in Illustration
*1 Voltage between terminals A-3 (+1) and B-2 (EW) *2 Voltage between terminals A-3 (+1) and B-2 (EW)
*3 Voltage between terminals A-3 (+1) and B-2 (EW) - -




b.

for RHD Windshield Wiper Switch LH Side Type:

i.
U170659E01
0.04,0.012 0.232,0.186 0.192,0.174 10 *a 0.463,0.866 0.769,1.046 0.306,0.180 10 B 2.867,0.856 3.162,1.019 0.295,0.163 10 A 3.051,0.538 3.259,0.700 0.208,0.163 10 +2 2.762,0.335 2.970,0.498 0.208,0.163 10 +1 2.257,0.248 2.464,0.410 0.208,0.163 10 +B 1.465,0.247 1.673,0.410 0.208,0.163 10 +S 2.014,1.53 2.331,1.693 0.317,0.163 10 WR 0.59,1.47 0.977,1.632 0.387,0.163 10 C1R 1.295,1.521 1.654,1.684 0.359,0.163 10 +1R 0.961,0.266 1.217,0.429 0.256,0.163 10 WF 0.387,0.361 0.658,0.523 0.271,0.163 10 EW 2.249,0.797 2.732,0.429 false 2.004,0.79 2.225,0.346 false 2.388,0.806 3.03,0.625 false 1.811,0.79 1.711,0.344 false 1.437,0.79 1.272,0.354 false 1.203,0.79 0.722,0.43 false 1.294,1.059 0.804,1.453 false 1.447,1.113 1.447,1.492 false 1.831,1.108 2.117,1.513 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Front Wiper Switch
Tester Connection Switch Condition Specified Condition
A-4 (+S) - A-2 (+1) OFF Below 1 Ω
INT
A-3 (+B) - A-2 (+1) MIST
LO
A-3 (+B) - A-1 (+2) HI

Front Washer Switch:
Tester Connection Switch Condition Specified Condition
B-2 (EW) - B-1 (WF) ON Below 1 Ω
OFF 10 kΩ or higher

Rear Wiper Switch:
Tester Connection Switch Condition Specified Condition
B-5 (C1R) - B-2 (EW) OFF 10 kΩ or higher
B-4 (+1R) - B-2 (EW)
B-5 (C1R) - B-2 (EW) INT Below 1 Ω
B-4 (+1R) - B-2 (EW) HI Below 1 Ω

Rear Washer Switch:
Tester Connection Switch Condition Specified Condition
A-10 (WR) - B-2 (EW) OFF 10 kΩ or higher
B-4 (+1R) - B-2 (EW)
A-10 (WR) - B-2 (EW) WASH Below 1 Ω
A-10 (WR) - B-2 (EW) ON + WASH Below 1 Ω
B-4 (+1R) - B-2 (EW)


If the result is not as specified, replace the windshield wiper switch assembly.

Text in Illustration
*a Component without harness connected
(Windshield Wiper Switch Assembly)


ii.

Check the intermittent operation.

1.

Connect the positive (+) lead of a voltmeter to terminal A-2 (+1) and the negative (-) lead to terminal B-2 (EW).

2.

Connect the positive (+) lead of the battery to terminal A-3 (+B) and the negative (-) lead to terminal B-2 (EW) and A-4 (+S).

3.

Turn the wiper switch to the INT position.

4.

Connect the positive (+) lead of the battery to terminal A-4 (+S) for 5 seconds.

5.

Connect the negative (-) lead of the battery to terminal A-4 (+S). Operate the intermittent wiper relay and check the voltage between terminals A-2 (+1) and B-2 (EW).

OK:

The voltage changes as shown in the illustration.


E056399E59
0.133,0.084 0.337,0.254 0.205,0.170 10 *1 1.734,0.549 2.453,0.700 0.719,0.151 10 10 to 14 V 2.2,1.028 2.474,1.184 0.274,0.156 10 0 V 2.484,1.463 3.642,1.627 1.158,0.164 10 1.6 +/- 1 second 2.699,0.205 2.896,0.366 0.197,0.161 10 *2 4.741,0.205 4.933,0.374 0.192,0.170 10 *3 4.625,1.454 5.884,1.610 1.259,0.155 10 10.7 +/- 5 seconds

If the result is not as specified, replace the windshield wiper switch assembly.

Text in Illustration
*1 Voltage between terminals A-2 (+1) and B-2 (EW) *2 Voltage between terminals A-2 (+1) and B-2 (EW)
*3 SLOW: Connect battery negative lead to terminal A-4 (+S) - -