Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT ASSEMBLY(for Halogen Headlight) › 2015.06–2017.08
RM27T0E _59 Vehicle Exterior _053747 LIGHTING (EXT) _0261276 HEADLIGHT ASSEMBLY(for Halogen Headlight) N

LIGHTING (EXT)  HEADLIGHT ASSEMBLY(for Halogen Headlight)  ADJUSTMENT  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

It is possible that a bulb is incorrectly installed, affecting headlight aim. Bulb installation should be considered prior to performing the adjustment procedure.



PROCEDURE

Hide 1. VEHICLE PREPARATION FOR HEADLIGHT AIMING ADJUSTMENT

a.

Prepare the vehicle:

·

Make sure that there is no damage to the body around the headlights.

·

Fill the fuel tank.

·

Make sure that the oil is filled to the specified level.

·

Make sure that the coolant is filled to the specified level.

·

Inflate the tires to the appropriate pressure.

·

Unload the trunk and vehicle, ensuring that the spare tire, tools and jack are in their original positions.

·

Have a person of average weight (75 kg, 165 lb) sit in the driver seat.

·

w/ Headlight Leveling:

Set the headlight leveling switch dial to 0.



Hide 2. PREPARATION FOR HEADLIGHT AIMING

E282542E04
1.01,1.615 1.323,1.885 0.313,0.271 10 false *a

a.

except China:

Prepare the vehicle:

Text in Illustration
*a 25 or 3 m

·

Place the vehicle in a location that is dark enough to clearly observe the cutoff line. The cutoff line is a distinct line, below which light from the headlights can be observed and above which it cannot.

·

Place the vehicle at a 90° angle to the wall.

·

Create a 25 m (82.0 ft.) distance between the vehicle (headlight bulb center) and wall.

·

Make sure that the vehicle is on a level surface.

·

Bounce the vehicle up and down to settle the suspension.


NOTICE:

A distance of 25 m (82.0 ft.) between the vehicle (headlight bulb center) and the wall is necessary for proper aim adjustment. If unavailable, secure a distance of exactly 3 m (9.84 ft.) for the check and adjustment. (The target zone will change with the distance, so follow the instructions in the illustration.)



b.
E282542E04
1.01,1.615 1.323,1.885 0.313,0.271 10 false *a

for China:

Prepare the vehicle:

Text in Illustration
*a 10 or 3 m

·

Place the vehicle in a location that is dark enough to clearly observe the cutoff line. The cutoff line is a distinct line, below which light from the headlights can be observed and above which it cannot.

·

Place the vehicle at a 90° angle to the wall.

·

Create a 10 m (32.8 ft.) distance between the vehicle (headlight bulb center) and the wall.

·

Make sure that the vehicle is on a level surface.

·

Bounce the vehicle up and down to settle the suspension.


NOTICE:

A distance of 10 m (32.8 ft.) between the vehicle (headlight bulb center) and the wall is necessary for proper aim adjustment. If unavailable, secure a distance of exactly 3 m (9.84 ft.) for the check and adjustment. (The target zone will change with the distance, so follow the instructions in the illustration.)



c.

Prepare a piece of thick white paper approximately 2 m (6.56 ft.) (height) x 4 m (13.1 ft.) (width) to use as a screen.


d.

Draw a vertical line down the center of the screen (V line).


e.

except China:

Set the screen as shown in the illustration.

HINT:
·

Stand the screen perpendicular to the ground.

·

Align the V line on the screen with the center of the vehicle.

E282543E06
0.771,0.042 3.042,0.26 2.271,0.219 12 false Alignment distance is 25 m: 4.344,0.042 6.396,0.25 2.052,0.208 12 false Alignment distance is 3 m: 1.146,0.448 1.948,0.625 0.802,0.177 10 false V RH Line 4.594,0.448 5.354,0.625 0.76,0.177 10 false V RH Line 1.125,1.583 1.75,1.76 0.625,0.177 10 false V LH Line 4.583,1.552 5.208,1.729 0.625,0.177 10 false V LH Line 3.25,1.115 3.656,1.292 0.406,0.177 10 false V Line 0.115,2.719 0.531,2.896 0.417,0.177 10 false H Line 3.76,2.719 4.177,2.896 0.417,0.177 10 false H Line 1.104,0.979 1.333,1.156 0.229,0.177 10 false 90° 4.729,0.979 4.958,1.156 0.229,0.177 10 false 90° 1.083,3.031 1.313,3.208 0.229,0.177 10 false 90° 4.74,3.042 4.969,3.219 0.229,0.177 10 false 90° 1.313,3.448 1.75,3.625 0.438,0.177 10 false 25 m 4.781,3.458 5.031,3.635 0.25,0.177 10 false 3 m 6.438,1.115 6.844,1.292 0.406,0.177 10 false V Line




f.

for China:

Set the screen as shown in the illustration.

HINT:
·

Stand the screen perpendicular to the ground.

·

Align the V line on the screen with the center of the vehicle.

E282543E07
0.75,0.063 3.031,0.281 2.281,0.219 12 false Alignment distance is 10 m: 4.344,0.073 6.458,0.281 2.115,0.208 12 false Alignment distance is 3 m: 1.083,0.51 1.729,0.688 0.646,0.177 10 false V RH Line 4.594,0.51 5.24,0.688 0.646,0.177 10 false V RH Line 1.073,1.552 1.698,1.729 0.625,0.177 10 false V LH Line 4.615,1.542 5.24,1.719 0.625,0.177 10 false V LH Line 3.25,1.094 3.656,1.271 0.406,0.177 10 false V Line 0.146,2.719 0.563,2.896 0.417,0.177 10 false H Line 3.75,2.729 4.167,2.906 0.417,0.177 10 false H Line 1.104,0.958 1.333,1.135 0.229,0.177 10 false 90° 4.75,0.969 4.979,1.146 0.229,0.177 10 false 90° 1.094,3.021 1.323,3.198 0.229,0.177 10 false 90° 4.729,3.031 4.958,3.208 0.229,0.177 10 false 90° 1.323,3.458 1.76,3.635 0.438,0.177 10 false 10 m 4.76,3.448 5.01,3.625 0.25,0.177 10 false 3 m 6.448,1.104 6.854,1.281 0.406,0.177 10 false V Line




g.

Prepare a piece of thick white paper approximately 2 m (6.56 ft.) (height) x 4 m (13.1 ft.) (width) to use as a screen.


h.

Draw a vertical line down the center of the screen (V line).


i.
E257183E01
1.17,0.275 1.331,0.419 0.161,0.143 10 *a 1.823,0.275 1.984,0.419 0.161,0.143 10 *b 2.446,0.275 2.607,0.419 0.161,0.143 10 *c 2.936,0.851 3.097,0.994 0.161,0.143 10 *d 0.547,1.698 0.708,1.841 0.161,0.143 10 *e

Draw base lines (H, V LH, and V RH Lines) on the screen as shown in the illustration.

Text in Illustration
*a V LH Line
*b V Line
*c V RH Line
*d H Line
*e Ground

HINT:
·

The base lines differ for "low beam inspection" and "high beam inspection".

·

Mark the headlight bulb center marks on the screen. If the center mark cannot be observed on the headlight, use the center of the headlight bulb or the name of the manufacturer marked on the headlight as the center mark.



i.

H Line (Headlight):

Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the headlight bulb center marks of the low beam headlights.


ii.

V LH Line, V RH Line (Center mark position of the left-hand (LH) and right-hand (RH) headlights):

Draw two vertical lines so that they intersect the H line at each center mark (aligned with the center of the low beam headlight bulbs).



Hide 3.INSPECT HEADLIGHT AIMING

a.

Cover the headlight or disconnect the connector of the headlight on the opposite side to prevent light from the headlight that is not being inspected from affecting the headlight aiming.

NOTICE:

Do not keep the headlight covered for more than 3 minutes. The headlight lens is made of synthetic resin, which may melt or be damaged due to excessive heat.


HINT:

When checking the aim of the high beam headlight, cover the low beam headlight or disconnect the connector.



b.

Start the engine.


c.

except China:

Turn on the headlight and check if the cutoff line matches the preferred cutoff line in the following illustration.

HINT:
·

Since the low beam light and the high beam light are a unit, if the aim on the low beam is correct, the high beam should also be correct. However, check both beams just to make sure.

·

If the alignment distance is 25 m (82.0 ft.):

The low beam cutoff line should be within 48 mm (1.89 in.) and 698 mm (2.29 ft.) below the H line as well as 249 mm (9.80 in.) left or right of the V LH or V RH line.

·

If the alignment distance is 3 m (9.84 ft.):

The low beam cutoff line should be within 6 mm (0.24 in.) and 84 mm (3.30 in.) below the H line as well as 30 mm (1.18 in.) left or right of the V LH or V RH line.

·

If the alignment distance is 25 m (82.0 ft.):

The horizontal line of the preferred low beam cutoff line is 249 mm (9.80 in.) below the H line and point A of the preferred low beam cutoff line is on the V LH or V RH line.

·

If the alignment distance is 3 m (9.84 ft.):

The horizontal line of the preferred low beam cutoff line is 30 mm (1.18 in.) below the H line and point A of the preferred low beam cutoff line is on the V LH or V RH line.

U170666E02
1.406,1.854 1.292,2.125 1.292,2.125 1.167,2.125 false 4.906,1.865 4.792,2.125 4.792,2.125 4.667,2.125 false 1.99,1.854 2.271,0.698 2.271,0.698 2.427,0.698 true 5.469,1.844 5.771,0.698 5.771,0.698 5.927,0.698 true 0.573,1.385 0.719,1.385 0.719,1.385 0.75,1.583 false 4.083,1.385 4.229,1.385 4.229,1.385 4.271,1.583 false 4.115,0.135 6.115,0.333 2,0.198 12 false Alignment distance is 3 m: 0.656,0.135 2.74,0.333 2.083,0.198 12 false Alignment distance is 25 m: 4.771,0.667 5.417,0.813 0.646,0.146 10 false V LH Line 4.771,0.948 5.448,1.104 0.677,0.156 10 false V RH Line 1.271,0.667 1.917,0.813 0.646,0.146 10 false V LH Line 1.271,0.948 1.948,1.104 0.677,0.156 10 false V RH Line 3.656,1.302 4.094,1.458 0.438,0.156 10 false H Line 0.146,1.302 0.583,1.458 0.438,0.156 10 false H Line 3.927,1.646 4.385,1.958 0.458,0.313 10 false 30 mm 0.354,1.625 0.875,1.938 0.521,0.313 10 false 249 mm 3.115,1.677 3.646,1.99 0.531,0.313 10 false 698 mm 1.51,1.219 1.958,1.531 0.448,0.313 10 false 48 mm 2.458,0.625 2.948,0.781 0.49,0.156 10 false Point A 5.958,0.625 6.448,0.781 0.49,0.156 10 false Point A 1.448,2.156 1.99,2.469 0.542,0.313 10 false 249 mm 5.542,2.156 6,2.469 0.458,0.313 10 false 30 mm 5.031,2.156 5.49,2.469 0.458,0.313 10 false 30 mm 2.031,2.156 2.604,2.469 0.573,0.313 10 false 249 mm 6.604,1.677 7.052,1.99 0.448,0.313 10 false 84 mm 5,1.219 5.385,1.531 0.385,0.313 10 false 6 mm 0.458,2.063 1.167,2.385 0.708,0.323 10 false Preferred Cutoff Line 3.958,2.063 4.667,2.385 0.708,0.323 10 false Preferred Cutoff Line 0.469,2.917 4.146,3.281 3.677,0.365 10 false The illustration shown is for LHD vehicles. RHD vehicles will project a headlight pattern that is a mirror image.




d.

for China:

Turn on the headlight and check if the cutoff line matches the preferred cutoff line in the following illustration.

HINT:
·

Since the low beam light and the high beam light are a unit, if the aim on the low beam is correct, the high beam should also be correct. However, check both beams just to make sure.

·

If the alignment distance is 10 m (32.8 ft.):

The low beam cutoff line should be within 95 mm (3.74 in.) and 286 mm (11.3 in.) below the H line as well as 99 mm (3.89 in.) left or right of the V LH or V RH line.

·

If the alignment distance is 3 m (9.84 ft.):

The low beam cutoff line should be within 29 mm (1.14 in.) and 86 mm (3.39 in.) below the H line as well as 30 mm (1.18 in.) left or right of the V LH or V RH line.

·

If the alignment distance is 10 m (32.8 ft.):

The horizontal line of the preferred low beam cutoff line is 190 mm (7.48 in.) below the H line and point A of the preferred low beam cutoff line is on the V LH or V RH line.

·

If the alignment distance is 3 m (9.84 ft.):

The horizontal line of the preferred low beam cutoff line is 57 mm (2.24 in.) below the H line and point A of the preferred low beam cutoff line is on the V LH or V RH line.

U149410E03
1.375,1.854 1.271,2.167 1.271,2.167 1.146,2.167 false 4.854,1.875 4.75,2.188 4.75,2.188 4.625,2.188 false 1.99,1.844 2.271,0.646 2.271,0.646 2.427,0.646 true 5.479,1.844 5.771,0.646 5.771,0.646 5.927,0.646 true 0.573,1.344 0.719,1.344 0.719,1.344 0.75,1.583 false 4.083,1.344 4.229,1.344 4.229,1.344 4.26,1.583 false 4.115,0.094 6.115,0.292 2,0.198 12 false Alignment distance is 3 m: 0.656,0.094 2.74,0.292 2.083,0.198 12 false Alignment distance is 10 m: 4.771,0.625 5.417,0.771 0.646,0.146 10 false V LH Line 4.771,0.906 5.448,1.063 0.677,0.156 10 false V RH Line 1.271,0.625 1.917,0.771 0.646,0.146 10 false V LH Line 1.271,0.906 1.948,1.063 0.677,0.156 10 false V RH Line 3.656,1.26 4.094,1.417 0.438,0.156 10 false H Line 0.146,1.26 0.583,1.417 0.438,0.156 10 false H Line 3.927,1.604 4.385,1.917 0.458,0.313 10 false 57 mm 0.354,1.604 0.875,1.917 0.521,0.313 10 false 190 mm 3.115,1.677 3.646,1.99 0.531,0.313 10 false 286 mm 1.51,1.177 1.958,1.49 0.448,0.313 10 false 95 mm 2.458,0.583 2.948,0.74 0.49,0.156 10 false Point A 5.958,0.583 6.448,0.74 0.49,0.156 10 false Point A 1.531,2.177 1.979,2.49 0.448,0.313 10 false 99 mm 5.542,2.177 6,2.49 0.458,0.313 10 false 30 mm 5.031,2.177 5.49,2.49 0.458,0.313 10 false 30 mm 6.604,1.677 7.052,1.99 0.448,0.313 10 false 86 mm 5,1.177 5.448,1.49 0.448,0.313 10 false 29 mm 0.479,2.083 1.188,2.406 0.708,0.323 10 false Preferred Cutoff Line 3.948,2.083 4.656,2.406 0.708,0.323 10 false Preferred Cutoff Line 2.021,2.177 2.469,2.49 0.448,0.313 10 false 99 mm




e.

except China:

Turn on the high beams and check if the center of intensity for each high beam matches the center of intensity in the illustration.

HINT:
·

Since the low beam light and the high beam light are a unit, if the aim on the low beam is correct, the high beam should also be correct. However, check both beams just to make sure.

·

If the alignment distance is 25 m (82.0 ft.):

The high beam center of intensity should be within 175 mm (6.88 in.) above and 249 mm (9.80 in.) below the H line as well as 497 mm (1.63 ft.) left or right of the V LH or V RH line.

·

If the alignment distance is 3 m (9.84 ft.):

The high beam center of intensity should be within 21 mm (0.82 in.) above and 30 mm (1.18 in.) below the H line as well as 60 mm (2.36 in.) left or right of the V LH or V RH line.

E235330E11
1.99,1.594 2.26,0.438 2.26,0.438 2.406,0.438 true 5.469,1.594 5.76,0.438 5.76,0.438 5.896,0.438 true 0.708,0 2.771,0.365 2.063,0.365 12 false Alignment distance is 25 m: 4.208,0 6.271,0.365 2.063,0.365 12 false Alignment distance is 3 m: 1.302,0.531 1.958,0.844 0.656,0.313 10 false V LH Line 0.521,1.5 0.948,1.802 0.427,0.302 10 false H Line 5.667,2.188 6.125,2.5 0.458,0.313 10 false 60 mm 4.865,2.188 5.323,2.5 0.458,0.313 10 false 60 mm 2.125,2.188 2.667,2.5 0.542,0.313 10 false 497 mm 1.344,2.188 1.885,2.5 0.542,0.313 10 false 497 mm 4.021,1.5 4.448,1.802 0.427,0.302 10 false H Line 6.604,1.74 7.083,2.052 0.479,0.313 10 false 30 mm 6.604,1.354 7.083,1.667 0.479,0.313 10 false 21 mm 3.135,1.76 3.688,2.073 0.552,0.313 10 false 249 mm 3.125,1.385 3.667,1.698 0.542,0.313 10 false 175 mm 2.458,0.365 3.083,1.01 0.625,0.646 10 false Center of Intensity 5.958,0.375 6.604,1.021 0.646,0.646 10 false Center of Intensity 1.302,0.813 1.958,1.177 0.656,0.365 10 false V RH Line 4.802,0.521 5.458,0.833 0.656,0.313 10 false V LH Line 4.802,0.802 5.458,1.167 0.656,0.365 10 false V RH Line




f.

for China:

Turn on the high beams and check if the center of intensity for each high beam matches the center of intensity in the illustration.

HINT:
·

Since the low beam light and the high beam light are a unit, if the aim on the low beam is correct, the high beam should also be correct. However, check both beams just to make sure.

·

If the alignment distance is 10 m (32.8 ft.):

The high beam center of intensity should be within 103 mm (4.06 in.) below the H line.

·

If the alignment distance is 3 m (9.84 ft.):

The high beam center of intensity should be within 31 mm (1.22 in.) below the H line.

·

If the alignment distance is 10 m (32.8 ft.):

The high beam center of intensity for the headlight assembly LH should be within 169 mm (6.65 in.) left and 349 mm (1.14 ft.) right of the V LH line.

·

If the alignment distance is 3 m (9.84 ft.):

The high beam center of intensity for the headlight assembly LH should be within 51 mm (2.01 in.) left and 105 mm (4.13 in.) right of the V LH line.

·

If the alignment distance is 10 m (32.8 ft.):

The high beam center of intensity for the headlight assembly RH should be within 349 mm (1.14 ft.) left or right of the V RH line.

·

If the alignment distance is 3 m (9.84 ft.):

The high beam center of intensity for the headlight assembly RH should be within 105 mm (4.13 in.) left or right of the V RH line.

E286571E05
2.625,2.698 2.531,2.698 2.531,2.698 1.99,3.906 false 3.219,2.948 3.115,2.948 3.115,2.948 2.885,3.448 false 3.313,3.208 3.208,3.208 3.208,3.208 3.104,3.438 false 2.49,0.51 2.396,0.51 2.396,0.51 1.854,1.719 false 3.073,0.771 2.969,0.771 2.969,0.771 2.75,1.271 false 3.167,1.021 3.073,1.021 3.073,1.021 2.958,1.26 false 5.969,2.688 5.865,2.688 5.865,2.688 5.323,3.896 false 6.552,2.938 6.448,2.938 6.448,2.938 6.229,3.448 false 6.646,3.198 6.552,3.198 6.552,3.198 6.438,3.427 false 5.948,0.5 5.854,0.5 5.854,0.5 5.313,1.708 false 6.542,0.76 6.438,0.76 6.438,0.76 6.219,1.26 false 6.615,1.021 6.521,1.021 6.521,1.021 6.417,1.25 false 0.969,0.083 3.115,0.292 2.146,0.208 12 false Alignment distance is 10 m: 4.646,0.083 6.688,0.292 2.042,0.208 12 false Alignment distance is 3 m: 0.573,1.313 0.99,1.458 0.417,0.146 10 false H Line 1.552,0.646 2.177,0.823 0.625,0.177 10 false V LH Line 1.125,3.302 1.625,3.479 0.5,0.177 10 false 99 mm 0.969,1.125 1.469,1.302 0.5,0.177 10 false 99 mm 2.365,3.417 2.865,3.594 0.5,0.177 10 false 99 mm 3.26,2.875 3.76,3.052 0.5,0.177 10 false 51 mm 2.646,2.625 3.802,2.792 1.156,0.167 10 false Center of Intensity 3.354,3.135 3.938,3.313 0.583,0.177 10 false 103 mm 0.729,3.521 1.146,3.667 0.417,0.146 10 false H Line 1.688,2.885 2.344,3.063 0.656,0.177 10 false V RH Line 2.021,4.271 2.552,4.417 0.531,0.146 10 false 349 mm 1.896,2.073 2.448,2.25 0.552,0.177 10 false 349 mm 1.271,2.073 1.802,2.24 0.531,0.167 10 false 169 mm 1.427,4.271 1.958,4.417 0.531,0.146 10 false 349 mm 3.375,3.75 3.969,3.927 0.594,0.177 10 false 154 mm 2.229,1.229 2.729,1.406 0.5,0.177 10 false 99 mm 3.115,0.698 3.615,0.875 0.5,0.177 10 false 51 mm 2.5,0.438 3.656,0.604 1.156,0.167 10 false Center of Intensity 3.208,0.948 3.792,1.125 0.583,0.177 10 false 103 mm 3.24,1.563 3.833,1.74 0.594,0.177 10 false 154 mm 4.031,1.313 4.448,1.458 0.417,0.146 10 false H Line 5.01,0.646 5.635,0.823 0.625,0.177 10 false V LH Line 4.458,3.292 4.958,3.469 0.5,0.177 10 false 30 mm 4.438,1.115 4.938,1.292 0.5,0.177 10 false 30 mm 5.698,3.385 6.198,3.563 0.5,0.177 10 false 30 mm 6.594,2.865 7.094,3.042 0.5,0.177 10 false 15 mm 5.979,2.625 7.135,2.792 1.156,0.167 10 false Center of Intensity 6.677,3.104 7.125,3.365 0.448,0.26 10 false 31 mm 4.063,3.51 4.479,3.656 0.417,0.146 10 false H Line 5.021,2.885 5.677,3.063 0.656,0.177 10 false V RH Line 5.354,4.26 5.885,4.406 0.531,0.146 10 false 105 mm 5.354,2.063 5.906,2.24 0.552,0.177 10 false 105 mm 4.729,2.063 5.26,2.229 0.531,0.167 10 false 51 mm 4.771,4.26 5.302,4.406 0.531,0.146 10 false 105 mm 6.677,3.75 7.135,4.052 0.458,0.302 10 false 46 mm 5.688,1.208 6.188,1.385 0.5,0.177 10 false 30 mm 6.583,0.688 7.083,0.865 0.5,0.177 10 false 15 mm 5.958,0.438 7.115,0.604 1.156,0.167 10 false Center of Intensity 6.635,0.938 7.115,1.198 0.479,0.26 10 false 31 mm 6.667,1.563 7.135,1.896 0.469,0.333 10 false 46 mm




Hide 4.ADJUST HEADLIGHT AIMING

a.

Using a screwdriver, adjust the aim.

Adjust the aim of each headlight so that it is within the specified range by turning each aiming screw with a screwdriver.

NOTICE:

The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it, and then retighten it so that the final turn of the screw is in the clockwise direction.


HINT:
·

The low beam and high beam headlights are a unit. Adjusting the aim on the low beam to the correct position should also result in the high beam adjustment being correct.

·

If it is not possible to correctly adjust headlight aim, check the bulb, headlight unit and headlight unit reflector installation.

·

The headlight aim moves up when turning the vertical aiming screw clockwise, and moves down when turning the vertical aiming screw counterclockwise. The headlight aim moves right when turning the horizontal aiming screw clockwise, and moves left when turning the horizontal aiming screw counterclockwise.

·

Confirm the direction of rotation of the aiming screw by observing it while it is being adjusted. Due to the position of the screwdriver, the direction of rotation of the adjusting screw can be different than the direction of rotation of the screwdriver being used to adjust it.

U170715E01
1.613,2.373 1.805,2.552 0.192,0.179 10 *1 0.257,0.874 0.449,1.053 0.192,0.179 10 *2 2.766,0.851 2.957,1.031 0.192,0.179 10 *3 2.233,0.23 2.424,0.409 0.192,0.179 10 *3 0.492,0.085 0.684,0.264 0.192,0.179 10 *A 4.21,0.099 4.401,0.279 0.192,0.179 10 *B 5.211,2.421 5.403,2.600 0.192,0.179 10 *1 3.817,0.973 4.008,1.152 0.192,0.179 10 *2 6.273,0.868 6.465,1.047 0.192,0.179 10 *3 5.722,0.222 5.914,0.401 0.192,0.179 10 *3 5.17,1.815 5.27,2.403 false 4.56,1.206 4,1.052 false 5.892,0.709 6.255,0.887 false 5.276,0.241 5.688,0.271 false 2.333,0.729 2.727,0.892 false 1.745,0.208 2.195,0.281 false 1.009,1.192 0.446,0.982 false 1.618,1.822 1.681,2.372 false



Text in Illustration
*A w/o Headlight Leveling *B w/ Headlight Leveling
*1 Vertical Aiming *2 Horizontal Aiming
*3 Screwdriver - -