Home › Vehicle Exterior › LIGHTING (EXT) › HAZARD WARNING SWITCH › 2015.06–2017.08
RM27T0E _59 Vehicle Exterior _053747 LIGHTING (EXT) _0261286 HAZARD WARNING SWITCH G

LIGHTING (EXT)  HAZARD WARNING SWITCH  INSPECTION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 84330 1.INSPECT HAZARD WARNING SIGNAL SWITCH ASSEMBLY (w/o Display)

E282730E05
0.106,0 0.345,0.216 0.239,0.216 10 *a

a.

Check the resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
3 - 16 Hazard warning signal switch off 10 kΩ or higher
Hazard warning signal switch on Below 1 Ω


If the result is not as specified, there may be a malfunction in the hazard warning signal switch assembly.

Text in Illustration
*a Component without harness connected
(Hazard Warning Signal Switch Assembly)



b.

Illumination inspection.

i.
E282730E06
2.01,1.313 2.125,1.792 true 0.594,0.531 1,1.021 true 2.021,1.802 2.417,2.021 0.396,0.219 10 false ILL+ 0.063,0 0.302,0.219 0.24,0.219 10 false *a 0.323,0.396 0.719,0.615 0.396,0.219 10 false ILL-

Apply battery voltage to the connector and check the illumination condition.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 11 (ILL+)
Battery negative (-) → Terminal 8 (ILL-)
Illuminates


If the result is not as specified, there may be a malfunction in the hazard warning signal switch assembly.

Text in Illustration
*a Component without harness connected
(Hazard Warning Signal Switch Assembly)



Hide 84330 2.INSPECT HAZARD WARNING SIGNAL SWITCH ASSEMBLY (w/ Display)

E107908E23
0.073,0 0.229,0.177 0.156,0.177 10 false *a

a.

Check the resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
4 - 1 Hazard warning signal switch off 10 kΩ or higher
Hazard warning signal switch on Below 1 Ω


If the result is not as specified, there may be a malfunction in the hazard warning signal switch assembly.

Text in Illustration
*a Component without harness connected
(Hazard Warning Signal Switch Assembly)



b.
E107908E19
0.106,0.016 0.262,0.198 0.156,0.181 10 *a 1.227,1.762 1.519,1.943 0.291,0.181 10 ILL+ 1.925,1.758 2.182,1.940 0.256,0.181 10 ILL- 1.586,1.311 1.392,1.736 false 1.878,1.324 2.007,1.75 false

Illumination inspection.

i.

Apply battery voltage to the connector and check the illumination condition.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 3 (ILL+)
Battery negative (-) → Terminal 2 (ILL-)
Illuminates


If the result is not as specified, there may be a malfunction in the hazard warning signal switch assembly.

Text in Illustration
*a Component without harness connected
(Hazard Warning Signal Switch Assembly)