Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › SIDE STEP
RM27T0E _59 Vehicle Exterior _053749 EXTERIOR PANELS / TRIM _0261304 SIDE STEP A

EXTERIOR PANELS / TRIM  SIDE STEP  DISASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 51793B 1.REMOVE SIDE STEP BRACKET LH

B236305

a.

Remove the 2 bolts and side step bracket.


Hide 51796 2.REMOVE NO. 2 SIDE STEP BRACKET LH

B236306

a.

Remove the 2 bolts and No. 2 side step bracket.


Hide 51798 3.REMOVE NO. 3 SIDE STEP BRACKET LH

B236307

a.

Remove the 2 bolts and No. 3 side step bracket.


Hide 75862C 4.REMOVE NO. 2 ROCKER PANEL MOULDING PROTECTOR

B236308

a.

Remove the 2 bolts and No. 2 rocker panel moulding protector.


Hide 51772D 5.REMOVE STEP PLATE LH (for 5 Door)

a.

Remove the clip and 3 bolts.


b.

Detach the 17 claws and remove the step plate.

B236309


Hide 51772D 6.REMOVE STEP PLATE LH (for 3 Door)

a.

Remove the clip and 3 bolts.


b.

Detach the 14 claws and remove the step plate.

B236310


Hide 51774C 7.REMOVE STEP PLATE COVER LH

a.

Remove the step plate cover.

B236311E01
0.058,0 0.292,0.198 0.235,0.198 10 *A 0.058,1.192 0.276,1.390 0.218,0.198 10 *B

Text in Illustration
*A for 5 Door *B for 3 Door


Hide 51779B 8.REMOVE NO. 2 SIDE STEP PLATE COVER

a.

Remove the No. 2 step plate cover.

B236312E01
0.088,0.016 0.391,0.199 0.303,0.184 10 *A 0.088,1.202 0.391,1.386 0.303,0.184 10 *B

Text in Illustration
*A for 5 Door *B for 3 Door


Hide 51077B 9.REMOVE SIDE STEP BRACKET SUB-ASSEMBLY LH

a.

Put a 4 mm (0.157 in.) drill bit into a drill.


b.
B236315E02
0.167,2.771 0.531,2.927 0.365,0.156 10 false 5 mm

Wind tape around the drill bit approximately 5 mm (0.197 in.) from the tip of the drill as shown in the illustration.

HINT:

Tape the 4 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.



c.

Lightly press the drill against the 3 rivets, drill off the flanges of the 3 rivets and remove the side step bracket.

CAUTION:

Be careful of the drilled rivet as it may become hot.


NOTICE:
·

Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

·

Do not pry the rivet with the drill because this may cause damage to the installation holes of the rivet or the drill bit.




d.

Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled area.


Hide 82158 10.REMOVE STEP PANEL WIRE LH (w/ Illumination)

Hide 81380D 11.REMOVE STEP LIGHT ASSEMBLY (w/ Illumination)

Hide 81399C 12.REMOVE STEP LIGHT BRACKET (w/ Illumination)

B236313E02
1.917,2.604 2.292,2.76 0.375,0.156 10 false 5 mm

a.

Put a 4 mm (0.157 in.) drill bit into a drill.


b.

Wind tape around the drill bit approximately 5 mm (0.197 in.) from the tip of the drill as shown in the illustration.

HINT:

Tape the 4 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.



c.

Lightly press the drill against the 3 rivets, drill off the flanges of the 3 rivets and remove the step light bracket.

CAUTION:

Be careful of the drilled rivet as it may become hot.


NOTICE:
·

Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

·

Do not pry the rivet with the drill because this may cause damage to the installation holes of the rivet or the drill bit.




d.

Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled area.


Hide 81380D 13.REMOVE STEP LIGHT ASSEMBLY (w/ Illumination)