Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › ROOF DRIP SIDE FINISH MOULDING
RM27T0E _59 Vehicle Exterior _053749 EXTERIOR PANELS / TRIM _0261310 ROOF DRIP SIDE FINISH MOULDING A

EXTERIOR PANELS / TRIM  ROOF DRIP SIDE FINISH MOULDING  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

When installing the roof drip side finish moulding clip, heat the vehicle body and clip using a heat light.

Standard:
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Roof Drip Side Finish Moulding Clip 20 to 30°C (68 to 86°F)




NOTICE:

Do not heat the vehicle body or clip excessively.


PROCEDURE

Hide 75561A 1.INSTALL ROOF DRIP SIDE FINISH MOULDING CLIP

NOTICE:
·

If reusing the clips, do not remove the double-sided tape remaining on the clips and where the clips will be installed on the body.

·

If installing new clips, remove the double-sided tape remaining where the clips will be installed on the body and clean the body with a non-residue solvent.



a.
B187426E02
2.064,0.824 2.371,0.824 false 1.851,0.727 2.080,0.914 0.229,0.187 10 *1 0.784,0.961 0.988,1.159 0.205,0.198 10 *a 0.986,1.073 1.226,1.073 1.226,1.073 1.347,1.528 false

Apply a 2 to 3 mm (0.0787 to 0.118 in.) bead of adhesive (3M DP-105 or equivalent) to new roof drip side finish moulding clips.

Text in Illustration
*1 Adhesive
*a 2 to 3 mm Bead of Adhesive

HINT:

Adhesive strength (tensile strength): 13.7 MPa (140.0 kgf/cm2, 1991 psi) or more (when the temperature is 23°C (73°F))



b.

Apply primer to the body where the roof drip side finish moulding clip will be installed.

NOTICE:

Do not let the primer dry.



c.

While using the position shown in the illustration as a reference, place the roof drip side finish moulding clip onto the roof panel. Then position and install the clip after lightly pressing it so that the adhesive adheres to the primer.

B236284E01
0.889,0.183 1.083,0.353 0.194,0.170 10 *A 4.09,1.262 4.267,1.418 0.177,0.156 10 *B 1.32,0.428 1.444,0.587 0.125,0.159 10 a 1.74,0.428 1.861,0.587 0.121,0.159 10 b 2.052,0.996 2.176,1.155 0.125,0.159 10 c 4.679,1.349 4.810,1.491 0.132,0.142 10 d 4.283,1.703 4.414,1.845 0.132,0.142 10 f 5.144,1.349 5.276,1.491 0.132,0.142 10 e

Text in Illustration
*A for Front Side *B for Rear Side

Reference Value:
Area Measurement Area Measurement
a 4 mm
0.157 in.
b 4 mm
0.157 in.
c 11 mm
0.433 in.
d 4 mm
0.157 in.
e 4 mm
0.157 in.
f 11 mm
0.433 in.


NOTICE:

Install the rear roof drip side finish moulding when 40 minutes or more have elapsed after pressing and installing the roof drip side finish moulding clips.


HINT:
·

Initial hardening time: 40 minutes

·

Complete hardening time: 48 hours




Hide 75552 2.INSTALL ROOF DRIP SIDE FINISH MOULDING LH

a.

Attach the clip to install the roof drip side finish moulding.


Hide 75558C 3.INSTALL CENTER NO. 2 ROOF DRIP SIDE FINISH MOULDING LH

a.

Install the center No. 2 roof drip side finish moulding.


Hide 75556C 4.INSTALL CENTER ROOF DRIP SIDE FINISH MOULDING LH

a.

Install the center roof drip side finish moulding.


Hide 75554A 5.INSTALL REAR ROOF DRIP SIDE FINISH MOULDING LH

a.

Attach the clip to install the rear roof drip side finish moulding.


Hide 75597 6.INSTALL ROOF DRIP SIDE FINISH MOULDING JOINT COVER LH (w/o Roof Rack)

HINT:

Use the same procedure to install the roof drip side finish moulding joint cover on the other side.


a.

Attach the 2 clamps to install the roof drip side finish moulding joint cover.


Hide 63470B 7.INSTALL ROOF RACK ASSEMBLY LH (w/ Roof Rack)