Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function) › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261052 ENTRY AND START SYSTEM(for Start Function) Y

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use these procedures to troubleshoot the push-button start function.

·

*: Use the intelligent tester.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS CHECK
2.CUSTOMER PROBLEM ANALYSIS CHECK
HINT:
·

In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.

·

Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.

·

The following 5 items are important points for problem analysis:

What Vehicle model, system name
When Date, time, occurrence frequency, whether the problem occurred recently or has been occurring for a long time
Where Whether the problem occurs at a specific location
Under what conditions? Whether the doors were locked or unlocked, whether the engine switch was on, whether the engine has started
How did it happen? Problem symptoms*



Result:
Result
NEXT



NEXT

3.INSPECT BATTERY VOLTAGE
3.INSPECT BATTERY VOLTAGE
Standard voltage:

11 to 14 V


If the voltage is below 11 V, recharge or replace the battery before proceeding.

Result:
Result
NEXT



NEXT

4.INSPECT COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
4.INSPECT COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
a.

Use the intelligent tester to check if the CAN communication system is functioning normally.

Result:
Result Proceed to
CAN DTC is not output A
CAN DTC is output for LHD with Entry and Start System B
for RHD with Entry and Start System C




A

5.CHECK FOR DTC*

B

C

5.CHECK FOR DTC*


c.

Recheck for DTCs.


Result:
Result Proceed to
DTC is not output again A
DTC is output again B



A

6.INSPECT BASIC OPERATION

B

6.INSPECT BASIC OPERATION

*1: for Automatic Transaxle

*2: for Manual Transaxle


a.

Check that the engine can be started by the basic operation.

i.

Push the engine switch when the brake pedal*1 or clutch pedal*2 is depressed and the shift lever is in P*1. Check that the engine starts.

OK:

Engine starts.




b.

Check that the engine switch mode can be changed by pushing the engine switch.

i.

Without depressing the brake pedal*1 or clutch pedal*2, push the engine switch repeatedly. Check that the power source mode turns from off to on (ACC) to on (IG) and back to off.

OK:

Power source mode changes as described above.



ii.

With the brake pedal*1 or clutch pedal*2 depressed and the shift lever in P*1, push the engine switch. Check that the engine starts normally from any power source mode status.

OK:

Engine starts normally from any power source mode status.




Result:
Proceed to
NEXT



NEXT

7.PROBLEM SYMPTOMS TABLE
7.PROBLEM SYMPTOMS TABLE

Result:
Result Proceed to
Fault is not listed in the problem symptoms table A
Fault is listed in the problem symptoms table B



A

8.OVERALL ANALYSIS AND TROUBLESHOOTING*

B

9.REPAIR OR REPLACE
8.OVERALL ANALYSIS AND TROUBLESHOOTING*

NEXT

9.REPAIR OR REPLACE
9.REPAIR OR REPLACE
Result:
Proceed to
NEXT



NEXT

10.CONFIRMATION TEST
10.CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END