This DTC is stored when the sliding roof drive gear sub-assembly detects that the sliding roof switch in the map light assembly is stuck for 30 seconds or more.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B2342 | The sliding roof drive gear sub-assembly detects that the sliding roof switch in the map light assembly is stuck for 30 seconds or more. | ·
Sliding roof drive gear sub-assembly (Sliding roof ECU) ·
Map light assembly (Sliding roof switch) ·
Harness or connector |
When the sliding roof drive gear sub-assembly is removed and reinstalled or replaced, the sliding roof drive gear sub-assembly must be initialized (See page Vehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION).
Using the GTS, read the Data List (See page Vehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Open Switch Failure (Past) | Slide open switch failure signal (Past) / ON or OFF | ON: Slide open switch signal failure (Past)
OFF: No slide open switch signal failure (Past) |
- |
| Close Switch Failure (Past) | Slide close switch failure signal (Past) / ON or OFF | ON: Slide close switch signal failure (Past)
OFF: No slide close switch signal failure (Past) |
- |
| Up Switch Failure (Past) | Tilt up switch failure signal (Past) / ON or OFF | ON: Tilt up switch signal failure (Past)
OFF: No tilt up switch signal failure (Past) |
- |
| Down Switch Failure (Past) | Tilt down switch failure signal (Past) / ON or OFF | ON: Tilt down switch signal failure (Past)
OFF: No tilt down switch signal failure (Past) |
- |
| Open Switch Failure (Current) | Slide open switch failure signal (Current) / ON or OFF | ON: Slide open switch signal failure (Current)
OFF: No slide open switch signal failure (Current) |
- |
| Close Switch Failure (Current) | Slide close switch failure signal (Current) / ON or OFF | ON: Slide close switch signal failure (Current)
OFF: No slide close switch signal failure (Current) |
- |
| Up Switch Failure (Current) | Tilt up switch failure signal (Current) / ON or OFF | ON: Tilt up switch signal failure (Current)
OFF: No tilt up switch signal failure (Current) |
- |
| Down Switch Failure (Current) | Tilt down switch failure signal (Current) / ON or OFF | ON: Tilt down switch signal failure (Current)
OFF: No tilt down switch signal failure (Current) |
- |
"OFF" appears on the GTS screen.
| Result | Proceed to |
|---|---|
| In part or in whole item displayed "ON" | A |
| All items are displayed "OFF" | B |
A
B
Remove the map light assembly (See page Vehicle Interior>LIGHTING (INT)>ROOM LIGHT(for Front)>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 8 (IG) - 23 (IG3) | Always | Below 1 Ω |
| 24 (UP) - 5 (GND3) | Tilt up switch pressed | Below 1 Ω |
| 24 (UP) - 5 (GND3) | Tilt up switch not pressed | 10 kΩ or higher |
| 25 (DOWN) - 5 (GND3) | Tilt down switch pressed | Below 1 Ω |
| 25 (DOWN) - 5 (GND3) | Tilt down switch not pressed | 10 kΩ or higher |
| 27 (OPN) - 5 (GND3) | Slide open switch pressed | Below 1 Ω |
| 27 (OPN) - 5 (GND3) | Slide open switch not pressed | 10 kΩ or higher |
| 28 (CLS) - 5 (GND3) | Slide close switch pressed | Below 1 Ω |
| 28 (CLS) - 5 (GND3) | Slide close switch not pressed | 10 kΩ or higher |
| *a | Component without harness connected
(Map Light Assembly) |
OK
NG
Disconnect the W20 ECU connector.
Disconnect the W7 switch connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| W20-4 (UP) - W7-24 (UP) | Always | Below 1 Ω |
| W20-6 (DWN) - W7-25 (DOWN) | Always | Below 1 Ω |
| W20-7 (OPN) - W7-27 (OPN) | Always | Below 1 Ω |
| W20-5(CLS) - W7-28 (CLS) | Always | Below 1 Ω |
| W7-5 (GND3) - Body ground | Always | Below 1 Ω |
| W20-12 (E) - Body ground | Always | Below 1 Ω |
| W20-1 (IG) - W7-23 (IG3) | Always | Below 1 Ω |
| W20-4 (UP) or W7-24 (UP) - Body ground | Always | 10 kΩ or higher |
| W20-6 (DWN) or W7-25 (DOWN) - Body ground | Always | 10 kΩ or higher |
| W20-7 (OPN) or W7-27 (OPN) - Body ground | Always | 10 kΩ or higher |
| W20-5 (CLS) or W7-28 (CLS) - Body ground | Always | 10 kΩ or higher |
| W20-1 (IG) or W7-23 (IG3) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| W7-8 (IG) - Body ground | Ignition switch off | Below 1 V |
| W7-8 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
OK
NG