The sliding roof drive gear sub-assembly (sliding roof ECU) receives each signal when the map light assembly (slide roof switch) is operated and drives its built-in motor.
When the sliding roof drive gear sub-assembly is removed and reinstalled or replaced, the sliding roof drive gear sub-assembly must be initialized (See page Vehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION).
Select the Active Test, use the GTS to generate a control command, and then check that the sliding roof slides open/closed and tilts up/down (See page Vehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Slide Roof | Operate sliding roof | Opn/Dwn: Sliding roof slide open or tilt down operation occurs
Clos/Up: Sliding roof slide close or tilt up operation occurs OFF: Sliding roof not operating |
- |
The sliding roof operates normally.
OK
NG
Using the GTS, read the Data List (See page Vehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Open Switch | Slide open switch signal / ON or OFF | ON: Slide open switch pressed
OFF: Slide open switch not pressed |
- |
| Close Switch | Slide close switch signal / ON or OFF | ON: Slide close switch pressed
OFF: Slide close switch not pressed |
- |
| Up Switch | Tilt up switch signal / ON or OFF | ON: Tilt up switch pressed
OFF: Tilt up switch not pressed |
- |
| Down Switch | Tilt down switch signal / ON or OFF | ON: Tilt down switch pressed
OFF: Tilt down switch not pressed |
- |
The GTS display changes according to switch operation as shown in the table.
OK
NG
Remove the map light assembly (See page Vehicle Interior>LIGHTING (INT)>ROOM LIGHT(for Front)>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 8 (IG) - 23 (IG3) | Always | Below 1 Ω |
| 24 (UP) - 5 (GND3) | Tilt up switch pressed | Below 1 Ω |
| 24 (UP) - 5 (GND3) | Tilt up switch not pressed | 10 kΩ or higher |
| 25 (DOWN) - 5 (GND3) | Tilt down switch pressed | Below 1 Ω |
| 25 (DOWN) - 5 (GND3) | Tilt down switch not pressed | 10 kΩ or higher |
| 27 (OPN) - 5 (GND3) | Slide open switch pressed | Below 1 Ω |
| 27 (OPN) - 5 (GND3) | Slide open switch not pressed | 10 kΩ or higher |
| 28 (CLS) - 5 (GND3) | Slide close switch pressed | Below 1 Ω |
| 28 (CLS) - 5 (GND3) | Slide close switch not pressed | 10 kΩ or higher |
| *a | Component without harness connected
(Map Light Assembly) |
OK
NG
Disconnect the W20 ECU connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| W20-12 (E) - Body ground | Always | Below 1 Ω |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| W20-1 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| W20-1 (IG) - Body ground | Ignition switch off | Below 1 V |
| *a | Front view of wire harness connector
(to Sliding Roof Drive Gear Sub-assembly) |
OK
NG
Disconnect the W20 ECU connector.
Disconnect the W7 switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| W20-4 (UP) - W7-24 (UP) | Always | Below 1 Ω |
| W20-5 (CLS) - W7-28 (CLS) | Always | Below 1 Ω |
| W20-6 (DWN) - W7-25 (DOWN) | Always | Below 1 Ω |
| W20-7 (OPN) - W7-27 (OPN) | Always | Below 1 Ω |
| W7-5 (GND3) - Body ground | Always | Below 1 Ω |
| W20-12 (E) - Body ground | Always | Below 1 Ω |
| W20-4 (UP) or W7-24 (UP) - Body ground | Always | 10 kΩ or higher |
| W20-5 (CLS) or W7-28 (CLS) - Body ground | Always | 10 kΩ or higher |
| W20-6 (DWN) or W7-25 (DOWN) - Body ground | Always | 10 kΩ or higher |
| W20-7 (OPN) or W7-27 (OPN) - Body ground | Always | 10 kΩ or higher |
OK
NG