Home › Vehicle Interior › HEATING / AIR CONDITIONING › FRONT AIR CONDITIONING UNIT › 2016.08–2020.08
RM27T0E _58 Vehicle Interior _053739 HEATING / AIR CONDITIONING _0261173 FRONT AIR CONDITIONING UNIT A

HEATING / AIR CONDITIONING  FRONT AIR CONDITIONING UNIT  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 88625 1.INSTALL NO. 1 COOLER THERMISTOR

U116483E04
2.01,2.542 2.708,2.542 false 2.573,2.771 2.708,2.771 false 2.677,2.552 2.677,2.729 false 0.719,3.073 1.792,3.073 false 0.604,2.156 0.604,3.125 true 0.719,2.042 0.719,2.333 true 1.938,2.563 1.938,3.135 true 0.323,2.76 0.146,2.76 false 0.771,2.333 0.156,2.333 true 0.24,2.354 0.24,2.698 false 0.281,2.24 0.188,2.24 false 0.292,2.073 0.198,2.073 false 0.323,2.073 0.719,2.073 true 0.313,2.24 0.604,2.24 true 0.771,2.073 0.865,2.073 false 0.635,2.24 0.708,2.24 false 0.094,2.438 0.219,2.604 0.125,0.167 10 false a 0.125,1.896 0.24,2.052 0.115,0.156 10 false b 0.073,2.125 0.188,2.292 0.115,0.167 10 false c 1.25,3.083 1.365,3.25 0.115,0.167 10 false d 2.74,2.552 2.854,2.719 0.115,0.167 10 false e 1.198,0.229 1.396,0.406 0.198,0.177 10 false *1

NOTICE:

If reusing the evaporator, do not insert the sensor into a location where the sensor was previously inserted.


a.

Insert the sensor to a location that is 1 fin to the right or left of its previous location.

Standard Dimension:
Area Specified Condition
a 50 mm (1.97 in.)
b 46.7 mm (1.84 in.)
c 33.3 mm (1.31 in.)
d 154.1 mm (6.07 in.)
e 25 mm (0.98 in.)


Text in Illustration
*1 1 Fin


Hide 88501 2.INSTALL NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY

a.

Sufficiently apply compressor oil to 2 new O-rings and the fitting surface of the hose joint.

Refrigerant Compressor Oil
HFC-134a (R134a) ND-OIL 8 or equivalent
HFO-1234yf (R1234yf) ND-OIL 12 or equivalent


b.

Install the 2 O-rings to the evaporator.


c.

Install the evaporator.


d.

Attach the 4 claws to install the unit case.


e.

Install the 6 screws.


Hide 87106D 3.INSTALL DAMPER SERVO SUB-ASSEMBLY LH

a.

Align the grooves on the damper servo sub-assembly with the protrusions on the unit and install the damper servo sub-assembly.

E349886E01
4.74,2.708 5.24,2.708 false 0.406,2.656 0.906,2.656 true 0.427,0.729 0.74,0.927 0.313,0.198 10 false *a 4.615,0.719 5.125,1.229 0.51,0.51 10 false *b 0.229,2.583 0.542,2.781 0.313,0.198 10 false *A 4.563,2.635 4.875,2.833 0.313,0.198 10 false *A

Text in Illustration
*A for Automatic Air conditioning System - -
*a Air Conditioning Unit Side *b Damper Servo Side


b.

Install the 4 screws.


Hide 87106L 4.INSTALL DAMPER SERVO SUB-ASSEMBLY RH

a.

Align the grooves on the damper servo sub-assembly with the protrusions on the unit and install the damper servo sub-assembly.

E349887E01
0.656,0.615 0.969,0.813 0.313,0.198 10 false *a 4.542,0.615 4.854,0.813 0.313,0.198 10 false *b

Text in Illustration
*a Air Conditioning Unit Side *b Damper Servo Side


b.

Install the 3 screws.


Hide 88515 5.INSTALL COOLER EXPANSION VALVE

a.

Install the expansion valve.


Hide 88710H 6.INSTALL AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY

a.

Sufficiently apply compressor oil to 2 new O-rings and the fitting surface of the hose joint.

Refrigerant Compressor Oil
HFC-134a (R134a) ND-OIL 8 or equivalent
HFO-1234yf (R1234yf) ND-OIL 12 or equivalent


b.

Install the 2 O-rings to the air conditioning tube and accessory assembly.


c.

Using a 4 mm hexagon wrench, install the 2 bolts.

Torque:
3.5 N*m (36 kgf*cm, 31 in.*lbf)


d.

Install new butyl tape.


e.

Install new packing.


Hide 7.INSTALL AIR CONDITIONING HARNESS

a.

Attach the clamps to install the harness.


b.

Connect the connectors.


Hide 87107A 8.INSTALL HEATER RADIATOR UNIT SUB-ASSEMBLY

a.

Install the heater radiator unit sub-assembly.


b.

Install the 2 radiator bracket with the 2 screws.


Hide 87710G 9.INSTALL QUICK HEATER ASSEMBLY (w/ PTC Heater)

Hide 88539J 10.INSTALL DRAIN COOLER HOSE

a.
E197396

Install the drain cooler hose.


Hide 88669B 11.INSTALL ASPIRATOR HOSE

a.

Attach the 2 claws to install the aspirator hose.


Hide 55950G 12.INSTALL DEFROSTER NOZZLE ASSEMBLY

a.

Attach the 6 claws to install the defroster nozzle assembly.


Hide 87130D 13.INSTALL BLOWER ASSEMBLY

a.

Attach the 2 claws to install the blower unit assembly.


b.

Connect the connector and clamp.


c.

Install the screw.

Torque:
2.7 N*m (28 kgf*cm, 24 in.*lbf)