Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMPRESSOR (for 1GR-FE) › from 2016.08
RM27T0E _58 Vehicle Interior _053739 HEATING / AIR CONDITIONING _0261179 COMPRESSOR(for 1GR-FE) A

HEATING / AIR CONDITIONING  COMPRESSOR(for 1GR-FE)  INSTALLATION  


PROCEDURE

Hide 1.ADJUST COMPRESSOR OIL

a.

When replacing the cooler compressor with a new one, gradually discharge the refrigerant gas from the service valve, and drain the following amount of oil from the new cooler compressor before installation.

Standard:

for Single Air Conditioning System:

(The amount of oil inside a new cooler compressor: 120 to 135 cc (4.1 to 4.6 fl. oz.)) - (The amount of oil remaining in the removed cooler compressor) = (The amount of oil to be removed when replacing the compressor)


Standard:

for Dual Air Conditioning System:

(The amount of oil inside a new cooler compressor: 180 to 195 cc (6.1 to 6.6 fl. oz.)) - (The amount of oil remaining in the removed cooler compressor) = (The amount of oil to be removed when replacing the compressor)


NOTICE:
·

When checking the compressor oil level, follow the A/C system precautions.

·

If a new cooler compressor is installed without removing some oil remaining in the pipes of the vehicle, the oil amount will be too large. This prevents heat exchange in the refrigerant cycle and causes refrigerant failure.

·

If the volume of oil remaining in the removed cooler compressor is too small, check for oil leakage.

·

for HFC-134a(R134a): Make sure to use ND-OIL 8 or equivalent compressor oil.

·

for HFO-1234yf(R1234yf): Make sure to use ND-OIL 12 or equivalent compressor oil.




Hide 88320 2.INSTALL COOLER COMPRESSOR ASSEMBLY

E195719E04
2.99,1.896 3.104,2.073 0.115,0.177 10 false 2 2.208,1.927 2.323,2.104 0.115,0.177 10 false 3 3.271,1.354 3.385,1.531 0.115,0.177 10 false 4 2.948,1.552 3.073,1.719 0.125,0.167 10 false 1

a.

Install the stud bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Temporarily install the cooler compressor assembly with the 3 bolts and nut.


c.

Tighten the 3 bolts and nut in the sequence shown in the illustration.

Torque:
for bolt : 25 N*m (255 kgf*cm, 18 ft.*lbf)
for nut : 25 N*m (255 kgf*cm, 18 ft.*lbf)


d.

Connect the connector.


Hide 88704 3.CONNECT SUCTION HOSE SUB-ASSEMBLY

a.

Remove the attached vinyl tape from the hose.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the cooler compressor.

Refrigerant Compressor Oil
HFC-134a (R134a) ND-OIL 8 or equivalent
HFO-1234yf (R1234yf) ND-OIL 12 or equivalent


c.

Install the O-ring to the suction hose.


d.
E195718E06
0.073,0.083 0.271,0.271 0.198,0.188 10 false *A 0.073,2.354 0.271,2.542 0.198,0.188 10 false *B 0.281,1.042 0.438,1.198 0.156,0.156 10 false C 0.385,3.313 0.542,3.469 0.156,0.156 10 false C 2.667,0.99 2.823,1.188 0.156,0.198 10 true D 2.781,3.281 2.948,3.479 0.167,0.198 10 true D

Connect the suction hose to the cooler compressor with the 2 bolts.

Torque:
for bolt C : 7.8 N*m (80 kgf*cm, 69 in.*lbf)
for bolt D : 9.8 N*m (100 kgf*cm, 87 in.*lbf)

Text in Illustration
*A for Type A
*B for Type B


Hide 88703 4.CONNECT DISCHARGE HOSE SUB-ASSEMBLY

a.

Remove the attached vinyl tape from the hose.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the cooler compressor.

Refrigerant Compressor Oil
HFC-134a (R134a) ND-OIL 8 or equivalent
HFO-1234yf (R1234yf) ND-OIL 12 or equivalent


c.

Install the O-ring to the discharge hose.


d.

Connect the discharge hose to the cooler compressor with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 27020 5.INSTALL GENERATOR ASSEMBLY

Hide 53292A 9.INSTALL UPPER RADIATOR SUPPORT SEAL