Use the following procedure to troubleshoot the audio and visual system.
*: Use the GTS.
| Proceed to |
|---|
| NEXT |
NEXT
When troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.
The following 5 items are important points in problem analysis:
| What | Vehicle model, system name |
| When | Date, time, occurrence frequency |
| Where | Road conditions |
| Under what conditions? | Driving conditions, weather conditions |
| How did it happen? | Problem symptoms |
| Proceed to |
|---|
| NEXT |
NEXT
Measure the battery voltage with the ignition switch off.
11 to 14 V
If the voltage is below 11 V, recharge or replace the battery.
| Proceed to |
|---|
| NEXT |
NEXT
Check that condensation is not likely to occur in the cabin, and that the temperature is not high or extremely low in the cabin.
Check that condensation is not likely to occur in the cabin, and that the temperature is not high or extremely low in the cabin.
A humid cabin and a rapid change in temperature may lead to condensation. Condensation in the cabin may cause a short circuit.
The audio and visual system may not operate normally when the temperature is -20°C (-4°F) or less, or 65°C (149°F) or higher.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for DTC output.
for LHD with Entry and Start System:
for LHD without Entry and Start System:
for RHD with Entry and Start System:
for RHD without Entry and Start System:
| Result | Proceed to |
|---|---|
| CAN DTCs are not output | A |
| CAN DTCs are output (for LHD with Entry and Start System) | B |
| CAN DTCs are output (for LHD without Entry and Start System) | C |
| CAN DTCs are output (for RHD with Entry and Start System) | D |
| CAN DTCs are output (for RHD without Entry and Start System) | E |
A
B
C
D
E
Refer to DTC Check/Clear.
| Proceed to |
|---|
| NEXT |
NEXT
Refer to DTC Check/Clear.
Even if the malfunction symptom is not confirmed, check for diagnostic trouble codes. This is because the system stores past diagnostic trouble codes.
After the check using the GTS, check the "System Check Mode" screen as necessary.
Check the diagnostic trouble code and inspect the area code indicates.
| Result | Proceed to |
|---|---|
| DTC is output | A |
| DTC is not output | B |
A
B
*1: w/ Rear View Monitor System (for Radio and Display Type)
*2: w/ Rear Seat Entertainment System
*3: w/ Parking Assist Monitor System (w/ Side Monitor System)
*4: w/ Wide View Front Monitor System
*5: w/ Side Monitor System
*6: w/ Telematics Transceiver
Find the output code in Diagnostic Trouble Code Chart.
The audio and visual system outputs DTCs for the following systems.
When DTCs other than the codes in Diagnostic Trouble Code Chart for the audio and visual system are output, refer to Diagnostic Trouble Code Chart for the following systems.
Refer to Rear View Monitor System (for Radio and Display Type). *1
Refer to Rear Seat Entertainment System. *2
Refer to Parking Assist Monitor System (w/ Side Monitor System). *3
Refer to Wide View Front Monitor System. *4
Refer to Side Monitor System. *5
Refer to Telematics System. *6
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
| Result | Proceed to |
|---|---|
| DTCs for the Audio and Visual System (w/ Radio and Display Type) are output | A |
| DTCs for the Rear View Monitor System (w/ Radio and Display Type) are output*1 | B |
| DTCs for the Rear Seat Entertainment System are output*2 | C |
| DTCs for the parking assist monitor system (w/ Side Monitor System) are output.*3 | D |
| DTCs for the wide view front monitor system are output.*4 | E |
| DTCs for the side monitor system are output.*5 | F |
| DTCs for the telematics system are output.*6 | G |
A
B
C
D
E
F
G
Refer to Problem Symptoms Table.
| Result | Proceed to |
|---|---|
| Fault is not listed in Problem Symptoms Table | A |
| Fault is listed in Problem Symptoms Table | B |
If the symptom does not recur and no DTC is output, perform the symptom reproduction method.
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
A
B
Refer to Terminals of ECU.
| Proceed to |
|---|
| NEXT |
NEXT
Adjust, repair or replace as necessary.
| Proceed to |
|---|
| NEXT |
NEXT
After clearing DTCs, recheck for DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT