There may be an open circuit in the CAN main wire and/or DLC3 CAN branch wire when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 70 Ω or higher.
| Symptom | Trouble Area |
|---|---|
| The resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 70 Ω or higher. | ·
CAN main wire and connector ·
ECM ·
No. 1 junction connector ·
No. 2 junction connector ·
No. 3 junction connector ·
No. 4 junction connector*1 ·
No. 5 junction connector*2 ·
Combination meter assembly ·
DLC3 CAN branch wire or connector |
*1: for 2TR-FE
*2: for 1GR-FE, 1KD-FTV, 1GD-FTV
Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.
After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
NEXT
Disconnect the G94 No. 3 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G94-5 (CANH) - G48-6 (CANH) | Engine switch off | Below 1 Ω |
| G94-16 (CANL) - G48-14 (CANL) | Engine switch off | Below 1 Ω |
| *a | Rear view of wire harness connector
(to No. 3 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G94-1 (CANH) - G94-12 (CANL) | Engine switch off | 108 to 132 Ω |
| *a | Rear view of wire harness connector
(to No. 3 Junction Connector) |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G94-6 (CANH) - G94-17 (CANL) | Engine switch off | 108 to 132 Ω |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G94-2 (CANH) - G94-13 (CANL) | Engine switch off | 108 to 132 Ω |
| *A | for 1GR-FE, 1KD-FTV, 1GD-FTV |
| *B | for 2TR-FE |
| *a | Rear view of wire harness connector
(to No. 3 Junction Connector) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for 1GR-FE, 1KD-FTV, 1GD-FTV) | B |
| NG (for 2TR-FE) | C |
A
B
C
Reconnect the G94 No. 3 junction connector.
NEXT
Disconnect the G100 No. 2 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G100-1 (CANH) - G100-12 (CANL) | Engine switch off | 108 to 132 Ω |
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G100-6 (CANH) - G100-17 (CANL) | Engine switch off | 108 to 132 Ω |
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
OK
NG
Reconnect the G100 No. 2 junction connector.
NEXT
Disconnect the G193 No. 1 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G193-6 (CANH) - G193-17 (CANL) | Engine switch off | 108 to 132 Ω |
| *a | Rear view of wire harness connector
(to No. 1 Junction Connector) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for 2TR-FE) | B |
| NG (for 1GR-FE) | C |
| NG (for 1KD-FTV) | D |
| NG (for 1GD-FTV) | E |
A
B
C
D
E
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G193-1 (CANH) - G193-12 (CANL) | Engine switch off | 108 to 132 Ω |
| *a | Rear view of wire harness connector
(to No. 1 Junction Connector) |
OK
NG
Reconnect the G193 No. 1 junction connector.
NEXT
Disconnect the A72 No. 4 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A72-10 (CANH) - A72-21 (CANL) | Engine switch off | 108 to 132 Ω |
| *a | Rear view of wire harness connector
(to No. 4 Junction Connector) |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A72-9 (CANH) - A72-20 (CANL) | Engine switch off | 108 to 132 Ω |
| *a | Rear view of wire harness connector
(to No. 4 Junction Connector) |
OK
NG
Reconnect the G193 No. 1 junction connector.
NEXT
Disconnect the G56 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G56-32 (CANH) - G56-31 (CANL) | Engine switch off | 108 to 132 Ω |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G56-31 (CANH) - G56-25 (CANL) | Engine switch off | 108 to 132 Ω |
| *A | for Manual Transmission System |
| *B | for Automatic Transmission System |
| *a | Front view of wire harness connector
(to ECM) |
OK
NG
Reconnect the G193 No. 1 junction connector.
NEXT
Disconnect the G58 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G58-35 (CANH) - G58-36 (CANL) | Engine switch off | 108 to 132 Ω |
| *a | Front view of wire harness connector
(to ECM) |
OK
NG
Reconnect the G193 No. 1 junction connector.
NEXT
Disconnect the G184 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G184-17 (CANH) - G184-28 (CANL) | Engine switch off | 108 to 132 Ω |
| *a | Front view of wire harness connector
(to ECM) |
OK
NG
Reconnect the A74 No. 4 junction connector.
NEXT
Disconnect the G181 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G181-13 (CANH) - G181- 14 (CANL) | Engine switch off | 108 to 132 Ω |
| *a | Front view of wire harness connector
(to ECM) |
OK
NG
Reconnect the G94 No. 3 junction connector.
NEXT
Disconnect the A73 No. 5 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A73-10 (CANH) - A73-21 (CANL) | Engine switch off | 108 to 132 Ω |
| *a | Rear view of wire harness connector
(to No. 5 Junction Connector) |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A73-9 (CANH) - A73-20 (CANL) | Engine switch off | 108 to 132 Ω |
| *a | Rear view of wire harness connector
(to No. 5 Junction Connector) |
OK
NG
Reconnect the A73 No. 5 junction connector.
NEXT
Disconnect the G6 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G6-40 (CANH) - G6-39 (CANL) | Engine switch off | 108 to 132 Ω |
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
OK
NG
Reconnect the G94 No. 3 junction connector.
NEXT
Disconnect the G6 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G6-40 (CANH) - G6-39 (CANL) | Engine switch off | 108 to 132 Ω |
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
OK
NG