Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › FRONT SPEED SENSOR › from 2016.08
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260913 FRONT SPEED SENSOR A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  FRONT SPEED SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

The procedure listed below is for the LH side.

·

Other than areas where instructions are provided, use the same procedures for the RH and LH sides.



PROCEDURE

Hide 89543 1.INSTALL FRONT SPEED SENSOR LH

a.
C361552C01
0.75,1.833 1,1.833 1,1.833 1,1.375 false 2.635,2.771 2.75,2.5 2.75,2.5 3,2.5 false 0.083,0.083 0.458,0.323 0.375,0.24 12 false *A 0.083,2.344 0.458,2.583 0.375,0.24 12 false *B 0.521,1.75 0.833,1.948 0.313,0.198 10 false *2 3.083,2.417 3.396,2.615 0.313,0.198 10 false *1
*A for LH
*B for RH
*1 No. 1 Skid Control Sensor Clamp
*2 No. 2 Skid Control Sensor Clamp


Install the front speed sensor LH with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:
·

Make sure there are no pieces of iron or other foreign matter attached to the front speed sensor LH tip.

·

While inserting the front speed sensor LH into the knuckle hole, do not strike or damage the sensor tip.

·

After installing the front speed sensor LH, make sure there is no clearance or foreign matter between the front speed sensor LH stay part and the knuckle.

·

Make sure there is no foreign matter attached to the speed sensor rotor.




Hide 89542 2.INSTALL FRONT SPEED SENSOR RH

HINT:

Use the same procedure described for the LH side.


Hide 3.INSTALL SKID CONTROL SENSOR CLAMP

a.

for LH:

Install the No. 2 skid control sensor clamp with the bolt.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)

NOTICE:

Install the clamp so that the rotation stopper touches the knuckle.



b.

for RH:

Install the No. 1 skid control sensor clamp with the bolt.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)

NOTICE:

Install the clamp so that the rotation stopper touches the knuckle.



Hide 89516 4.INSTALL SKID CONTROL SENSOR WIRE (except 1GD-FTV)

a.

Connect the connector as follows.

C212843C06
5.833,1 6.417,0.417 6.417,0.417 6.667,0.417 true 0.188,0.125 0.5,0.323 0.313,0.198 12 false *A 3.958,0.115 4.229,0.313 0.271,0.198 12 false *B 6.75,0.333 7.063,0.531 0.313,0.198 10 false *1
*A for LH *B for RH
*1 NO. 3 SKID CONTROL SENSOR CLAMP - -


i.

for LH:

1. Attach the connector, and then connect the connector.

NOTICE:
·

Securely connect the connector.

·

When connecting the connector, do not twist the wire harness.




ii.

for RH:

1. Install the No. 3 skid control sensor clamp with the bolt.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)

NOTICE:

Make sure the clamp rotation stopper touches the installation position.


2. Attach the connector, and then connect the connector.

NOTICE:
·

Securely connect the connector.

·

When connecting the connector, do not twist the wire harness.



3. Attach the clip.



b.
C212841

Install the 2 harness clamps with the 2 bolts.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)

NOTICE:
·

When installing the clamps, do not twist the wire harness.

·

Make sure the clamp rotation stopper touches the installation position.




c.
C212840

Install the 2 harness clamps with the 2 bolts.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)

NOTICE:
·

When installing the clamps, do not twist the wire harness.

·

Make sure the clamp rotation stopper touches the installation position.




d.

Attach the clip.


e.

Connect the connector.

NOTICE:

Securely connect the connector.



Hide 89516 5.INSTALL SKID CONTROL SENSOR WIRE (for 1GD-FTV)

a.

Connect the connector as follows.

C361503C01
5.167,1.125 5.167,0.188 5.167,0.188 6.052,0.188 true 0.125,0.094 0.5,0.333 0.375,0.24 12 false *A 3.906,0.094 4.281,0.333 0.375,0.24 12 false *B 6.167,0.115 6.479,0.313 0.313,0.198 10 false *1
*A for LH *B for RH
*1 NO. 3 SKID CONTROL SENSOR CLAMP - -


i.

for LH:

1.

Attach the connector, and then connect the connector.

NOTICE:
·

Securely connect the connector.

·

When connecting the connector, do not twist the wire harness.





ii.

for RH:

1.

Install the No. 3 skid control sensor clamp with the bolt.

Torque:

5.0 N*m (51 kgf*cm, 44 in.*lbf)


NOTICE:

Make sure the clamp rotation stopper touches the installation position.


2.

Attach the connector clamp, and then connect the connector.

3.

Attach the 2 clips.




b.

Install the 2 harness clamps with the 2 bolts.

C361502C01
0.135,0.104 0.51,0.344 0.375,0.24 12 false *A 4.021,0.104 4.396,0.344 0.375,0.24 12 false *B
*A for LH *B for RH


Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)

NOTICE:
·

When installing the clamps, do not twist the wire harness.

·

Make sure the clamp rotation stopper touches the installation position.




c.
C212840

Install the 2 harness clamps with the 2 bolts.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)

NOTICE:
·

When installing the clamps, do not twist the wire harness.

·

Make sure the clamp rotation stopper touches the installation position.




d.

Attach the clip.


e.

Connect the connector.

NOTICE:

Securely connect the connector.



Hide 42603 6.INSTALL FRONT WHEEL

Torque:
for Aluminum Wheel : 103 N*m (1050 kgf*cm, 76 ft.*lbf)
for Steel Wheel : 112 N*m (1137 kgf*cm, 82 ft.*lbf)

Hide 89543 7.CHECK SPEED SENSOR SIGNAL