Home › Vehicle Interior › SEAT › SEAT HEATER SWITCH(for Front Seat) › from 2017.08
RM27T0E _58 Vehicle Interior _053737 SEAT _0261124 SEAT HEATER SWITCH(for Front Seat) G

SEAT  SEAT HEATER SWITCH(for Front Seat)  INSPECTION  


PROCEDURE

Hide 1.INSPECT SEAT HEATER SWITCH

B487830C01
1.781,1.448 2.292,1.052 true 5.448,1.396 5,1.052 true 4.844,1.823 4.219,2.031 true 2.896,1.719 3.094,2.01 true 2.531,1.844 2.938,2.042 true 4.219,2.229 4.625,2.427 true 3.458,2.25 3.656,2.521 true 3.281,2.26 3.281,2.521 true 2.927,2.208 2.531,2.208 true 3.104,2.25 2.833,2.51 true 1.615,1.417 1.833,1.615 0.219,0.198 10 false *1 5.479,1.365 5.708,1.594 0.229,0.229 10 false *2 3.479,1.604 3.792,1.76 0.313,0.156 10 false *a 4.885,1.698 5.26,1.906 0.375,0.208 10 false ILL- 2.74,1.521 3.115,1.729 0.375,0.208 10 false ILL+ 2.344,1.698 2.656,1.917 0.313,0.219 10 false IG 4.667,2.365 4.979,2.583 0.313,0.219 10 false E 3.615,2.542 3.927,2.76 0.313,0.219 10 false RV 3.198,2.552 3.51,2.771 0.313,0.219 10 false RV 2.24,2.115 2.615,2.333 0.375,0.219 10 false SW 2.677,2.531 3.052,2.75 0.375,0.219 10 false SW
*1 LH Switch *2 RH Switch
*a Component without harness connected
(Seat Heater Switch)
- -


a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
9 (RV) - 11 (SW) LH switch off (Dial position 0) 2.17 to 4.03 kΩ
LH switch on (Dial position 1) 1.69 to 3.15 kΩ
LH switch on (Dial position 2) 1.01 to 1.87 kΩ
LH switch on (Dial position 3) 0.28 to 0.52 kΩ
10 (RV) - 12 (SW) RH switch off (Dial position 0) 2.17 to 4.03 kΩ
RH switch on (Dial position 1) 1.69 to 3.15 kΩ
RH switch on (Dial position 2) 1.01 to 1.87 kΩ
RH switch on (Dial position 3) 0.28 to 0.52 kΩ


HINT:

As the dial is being turned, the resistance changes gradually.


If the result is not as specified, replace the seat heater switch.


b.

Apply battery voltage to the switch connector, and check that the seat heater switch illuminates.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 2 (ILL+)
Battery negative (-) → 1 (ILL-)
Illuminates


If the result is not as specified, replace the seat heater switch.


c.

Apply battery voltage to the switch connector, and check that the seat heater switch indicator illuminates.

OK:
Measurement Condition Switch Condition Specified Condition
Battery positive (+) → 3 (IG)
Battery negative (-) → 4 (E)
LH switch on LH switch indicator illuminates
RH switch on RH switch indicator illuminates


If the result is not as specified, replace the seat heater switch.