Home › Vehicle Interior › SEAT › CLIMATE CONTROL SEAT SWITCH(w/ Climate Control Seat System) › from 2017.08
RM27T0E _58 Vehicle Interior _053737 SEAT _0261143 CLIMATE CONTROL SEAT SWITCH(w/ Climate Control Seat System) G

SEAT  CLIMATE CONTROL SEAT SWITCH(w/ Climate Control Seat System)  INSPECTION  


PROCEDURE

Hide 84752 1.INSPECT REFRESHING SEAT SWITCH (w/o Seat Heater System)

B487831C01
1.771,1.375 2.281,1.01 true 5.51,1.375 5,1.01 true 4.219,2.031 4.615,1.906 true 3.104,2 2.896,1.74 true 2.938,2.042 2.583,1.948 true 4.573,2.313 4.219,2.219 true 4.198,2.521 4.052,2.26 true 3.75,2.51 3.854,2.26 true 3.292,2.51 3.552,2.26 true 1.604,1.323 1.917,1.479 0.313,0.156 10 false *1 5.542,1.344 5.854,1.5 0.313,0.156 10 false *2 3.479,1.615 3.792,1.771 0.313,0.156 10 false *a 4.656,1.771 4.979,2.01 0.323,0.24 10 false ILL- 2.75,1.552 3.073,1.75 0.323,0.198 10 false ILL+ 2.396,1.813 2.646,2.021 0.25,0.208 10 false IG 4.615,2.25 4.865,2.458 0.25,0.208 10 false E 4.083,2.542 4.531,2.74 0.448,0.198 10 false SVSG 3.552,2.542 4,2.74 0.448,0.198 10 false BLRH 3.083,2.542 3.531,2.74 0.448,0.198 10 false BLLH
*1 LH Switch *2 RH Switch
*a Component without harness connected
(Refreshing Seat Switch)
- -


a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
5 (SVSG) - 8 (BLLH) LH switch off (Dial position 0) 1.54 to 2.86 kΩ
LH switch on (Dial position 1) 0.76 to 1.41 kΩ
LH switch on (Dial position 2) 0.56 to 1.03 kΩ
LH switch on (Dial position 3) 0.22 to 0.41 kΩ
5 (SVSG) - 6 (BLRH) RH switch off (Dial position 0) 1.54 to 2.86 kΩ
RH switch on (Dial position 1) 0.76 to 1.41 kΩ
RH switch on (Dial position 2) 0.56 to 1.03 kΩ
RH switch on (Dial position 3) 0.22 to 0.41 kΩ


HINT:

As the dial is being turned, the resistance changes gradually.


If the result is not as specified, replace the refreshing seat switch.


b.

Apply battery voltage to the switch connector, and check that the refreshing seat switch illuminates.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 2 (ILL+)
Battery negative (-) → 1 (ILL-)
Illuminates


If the result is not as specified, replace the refreshing seat switch.


c.

Apply battery voltage to the switch connector, and check that the refreshing seat switch indicator illuminates.

OK:
Measurement Condition Switch Condition Specified Condition
Battery positive (+) → 3 (IG)
Battery negative (-) → 4 (E)
LH switch on LH switch indicator illuminates
RH switch on RH switch indicator illuminates


If the result is not as specified, replace the refreshing seat switch.


Hide 84752 2.INSPECT REFRESHING SEAT SWITCH (w/ Seat Heater System)

B487829C01
1.677,1.344 2.281,1.042 true 5.635,1.344 5.031,1.031 true 3.135,2 3.188,1.74 true 4.219,2.042 4.552,1.979 true 4.219,2.208 4.573,2.302 true 3.427,2.26 3.365,2.51 true 2.615,1.865 2.938,2.042 true 3.26,2.26 3.063,2.521 true 3.094,2.26 2.604,2.479 true 2.594,2.208 2.927,2.208 true 4.063,2.25 4.51,2.531 true 3.906,2.26 4.146,2.51 true 3.594,2.26 3.688,2.51 true 1.479,1.302 1.792,1.458 0.313,0.156 10 false *1 5.677,1.313 5.99,1.469 0.313,0.156 10 false *2 3.49,1.615 3.802,1.771 0.313,0.156 10 false *c 3.365,1.292 3.573,1.49 0.208,0.198 10 true *a 3.792,1.292 4.021,1.5 0.229,0.208 10 false *b 4.594,1.854 4.99,2.073 0.396,0.219 10 false ILL- 3.104,1.563 3.5,1.781 0.396,0.219 10 false ILL+ 4.969,1.281 5.177,1.479 0.208,0.198 10 true *a 2.146,1.292 2.354,1.49 0.208,0.198 10 true *b 4.604,2.219 5,2.438 0.396,0.219 10 false E 2.438,1.729 2.708,1.958 0.271,0.229 10 false IG 3.26,2.542 3.531,2.75 0.271,0.208 10 false RV 2.917,2.542 3.188,2.75 0.271,0.208 10 false RV 2.313,2.115 2.635,2.323 0.323,0.208 10 false SW 2.333,2.469 2.625,2.677 0.292,0.208 10 false SW 4.542,2.521 5.01,2.729 0.469,0.208 10 false SVSG 4.021,2.531 4.49,2.74 0.469,0.208 10 false BLRH 3.552,2.542 4.021,2.75 0.469,0.208 10 false BLLH
*1 LH Switch *2 RH Switch
*a for Seat Heater *b for Seat Blower
*c Component without harness connected
(Refreshing Seat Switch)
- -


a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
5 (SVSG) - 8 (BLLH) LH switch off (Dial position 0) 1.54 to 2.86 kΩ
LH switch on (Seat blower dial position 1) 0.76 to 1.41 kΩ
LH switch on (Seat blower dial position 2) 0.56 to 1.03 kΩ
LH switch on (Seat blower dial position 3) 0.22 to 0.41 kΩ
9 (RV) - 11 (SW) LH switch off (Dial position 0) 2.17 to 4.03 kΩ
LH switch on (Seat heater dial position 1) 1.69 to 3.15 kΩ
LH switch on (Seat heater dial position 2) 1.01 to 1.87 kΩ
LH switch on (Seat heater dial position 3) 0.28 to 0.52 kΩ
5 (SVSG) - 6 (BLRH) RH switch off (Dial position 0) 1.54 to 2.86 kΩ
RH switch on (Seat blower dial position 1) 0.76 to 1.41 kΩ
RH switch on (Seat blower dial position 2) 0.56 to 1.03 kΩ
RH switch on (Seat blower dial position 3) 0.22 to 0.41 kΩ
10 (RV) - 12 (SW) RH switch off (Dial position 0) 2.17 to 4.03 kΩ
RH switch on (Seat heater dial position 1) 1.69 to 3.15 kΩ
RH switch on (Seat heater dial position 2) 1.01 to 1.87 kΩ
RH switch on (Seat heater dial position 3) 0.28 to 0.52 kΩ


HINT:

As the dial is being turned, the resistance changes gradually.


If the result is not as specified, replace the refreshing seat switch.


b.

Apply battery voltage to the switch connector, and check that the refreshing seat switch illuminates.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 2 (ILL+)
Battery negative (-) → 1 (ILL-)
Illuminates


If the result is not as specified, replace the refreshing seat switch.


c.

Apply battery voltage to the switch connector, and check that the refreshing seat switch indicator illuminates.

OK:
Measurement Condition Switch Condition Specified Condition
Battery positive (+) → 3 (IG)
Battery negative (-) → 4 (E)
LH switch on (Heater) LH switch indicator illuminates
LH switch on (Blower)
RH switch on (Heater) RH switch indicator illuminates
RH switch on (Blower)


If the result is not as specified, replace the refreshing seat switch.