Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Manual Air Conditioning System) › from 2017.08
RM27T0E _58 Vehicle Interior _053739 HEATING / AIR CONDITIONING _0261170 AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) D

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)  SYSTEM DESCRIPTION  


GENERAL


a.

The air conditioning system has the following controls.

Control Outline
Manual Control The air conditioning amplifier assembly controls the damper positions (air inlet control damper, air mix control damper and mode control damper) and blower speed in accordance with the positions of the switches (temperature control dial, blower dial, mode operation switch and REC/FRS switch).
Air Inlet Control Drives the recirculation damper servo sub-assembly according to the operation of the REC/FRS switch and moves the dampers to the fresh or recirculation position.
Compressor Control The air conditioning amplifier assembly compares the A/C pulley speed signals, which are transmitted by the ECM (crankshaft position sensor). When the air conditioning amplifier assembly determines that the A/C pulley is locked, it turns off the magnet clutch assembly.
Defroster Control Defroster control logic is used to improve defroster performance.
Defroster Fresh Air Mode Switching Control Defroster fresh air mode switching control changes the system from recirculation air mode to fresh air mode to improve defroster performance.
Rear Defogger Control When the ignition switch is ON and the rear defogger switch is pushed, the system is activated to keep the defogger heater on for approx. 15 minutes. However, the operating time of the rear defogger can be extended up to approx. 255 minutes when both of the following requirements are met:
·

Ambient Temperature: -3°C (26.6°F) or less

·

Vehicle Speed: 50 km/h (31.1 mph) or more


Diagnosis A Diagnostic Trouble Code (DTC) is stored in memory when the air conditioning amplifier assembly detects a problem with the air conditioning system.



MODE POSITION AND DAMPER OPERATION


a.

Mode Position and Damper Operation

i.

Front Air Conditioning Unit

E203283E04
0.264,1.771 0.805,1.962 0.541,0.191 10 Fresh 2.336,0.082 3.342,0.273 1.006,0.191 10 Front Defroster 0.649,4.295 1.518,4.486 0.870,0.191 10 Blower Motor 4.623,4.681 5.572,5.083 0.948,0.402 10 Rear Footwell Register Duct 3.672,3.695 4.663,4.092 0.991,0.397 10 Front Footwell Register Duct 6.417,3.695 7.016,4.047 0.599,0.352 10 Side Register 4.915,3.695 5.768,4.042 0.852,0.347 10 Front Center Register 0.874,3.953 1.728,4.144 0.854,0.191 10 Evaporator 1.154,4.631 1.988,4.821 0.833,0.191 10 Heater Core 1.156,1.771 2.403,1.962 1.247,0.191 10 Recirculation 2.574,3.816 2.087,4.707 2.087,4.707 1.997,4.707 false 0.555,4.911 2.232,5.101 1.678,0.191 10 Quick Heater Assembly*2 2.776,3.745 2.339,4.987 2.339,4.987 2.249,4.987 false 5.726,5.347 6.476,5.742 0.750,0.395 10 Rear Face Register*1 1.245,3.959 1.245,3.823 1.245,3.823 2.021,3.412 false 0.601,4.36 0.489,4.36 0.489,4.36 0.818,3.384 false 4.148,0.764 5.154,0.955 1.006,0.191 10 Front Defroster 0.557,0.764 1.562,0.955 1.006,0.191 10 Front Defroster 0.182,6.085 2.659,6.275 2.477,0.191 10 *1: w/o Rear Air Conditioning System 0.182,6.365 2.659,6.556 2.477,0.191 10 *2: w/ PTC Heater

Function of Main Damper
Control Damper Operation Position Damper Position Operation
Air Inlet Control Damper Fresh A Brings in fresh air.
Recirculation B Recirculates internal air.
Air Mix Control Damper MAX COOL to MAX HOT E - D - C Varies the mixture of cold air and hot air in order to regulate the temperature continuously from hot to cool.
MAX COOL Damper MAX COOL V Open in the MAX COOL position.
Except MAX COOL W Close in all position except MAX COOL position.
MAX HOT Damper MAX HOT Y Open in the MAX HOT position.
Except MAX HOT X Closed in all position except MAX HOT position.
Mode Control Damper
E264852

Face
F, I, N, T, X Air blows out of the front center registers, side registers and rear face registers.
E264849

Bi-level
G, L, N, T, X Air blows out of the front center registers, side registers, rear face registers and front and rear footwell register ducts.
E264850

Foot
H, M, P, T, W, Y (MAX HOT position)
H, M, O, T, X (Except MAX HOT position)
Air blows out of the front and rear footwell register ducts.
In addition, air blows out slightly from the front defroster, side registers, front center registers and rear face registers.
E264851

Foot/Def
H, K, R, T, W, Y (MAX HOT position)
H, M, Q, T, X (Except MAX HOT position)
Defrosts the windshield through the front defroster and side registers while air is also blown out from the front and rear footwell register ducts.
In addition, air blows out slightly from the front center registers and rear face registers.
E264847

Def
H, I, S, U, X Defrosts the windshield through the front defrosters.


ii.

Rear Air Conditioning Unit (w/ Rear Air Conditioning System)

U116434E01
0.856,2.601 2.074,2.785 1.218,0.184 10 Rear Blower Motor 2.67,3.182 3.402,3.359 0.732,0.177 10 Evaporator 1.255,0.373 2.633,0.571 1.378,0.198 10 Rear Heater Radiator 3.435,0.269 4.133,0.620 0.698,0.350 10 Rear Side Register 4.59,0.506 5.444,0.815 0.855,0.309 10 Rear Roof Register 3.539,1.13 3.715,1.307 0.177,0.177 10 C 3.842,1.244 4.001,1.403 0.159,0.159 10 B 4.127,1.326 4.273,1.513 0.145,0.187 10 A 4.463,1.592 4.593,1.750 0.130,0.158 10 C 4.691,1.729 4.837,1.901 0.146,0.172 10 B 4.94,1.956 5.066,2.156 0.126,0.199 10 A 4.764,1.929 4.925,2.118 0.161,0.189 10 D 4.384,2.026 4.564,2.234 0.180,0.208 10 E 3.637,1.601 3.774,1.769 0.137,0.168 10 E 3.637,1.816 3.800,1.979 0.163,0.163 10 D 2.378,1.868 1.416,2.377 false 1.416,2.377 1.416,2.601 false 3.896,2.634 2.995,3.026 false 2.995,3.026 2.995,3.182 false 3.322,1.167 2.817,0.448 false 2.817,0.448 2.628,0.448 false

Function of Main Damper
Control Damper Operation Position Damper Position Operation
Mode Control Damper
E264852

Face
A Air blows out from the rear roof registers.
E264849

Bi-level
B Air blows out from the rear roof registers and rear side registers.
E264850

Foot
C Air blows out from the rear side registers.
Air Mix Control Damper MAX COLD to MAX HOT Temperature Setting D, E Varies the mixture of cold air and hot air in order to regulate the temperature continuously from hot to cold.




AIR OUTLETS AND AIRFLOW VOLUME


a.

Air Outlets and Airflow Volume

i.

for Front Registers

E371920E01
1.781,1.469 1.938,1.667 0.156,0.198 10 false F 2.427,1.292 2.583,1.49 0.156,0.198 10 false F 3.063,1.156 3.219,1.354 0.156,0.198 10 false F 5.583,1.635 5.74,1.833 0.156,0.198 10 false F 5.469,2.333 5.625,2.531 0.156,0.198 10 false B 4.552,3.479 4.708,3.677 0.156,0.198 10 true C 4.135,3.677 4.438,3.927 0.302,0.25 10 true C 0.625,2.854 0.781,3.052 0.156,0.198 10 false F 1.729,3.333 2.031,3.583 0.302,0.25 10 true B 1.813,4.24 2.115,4.49 0.302,0.25 10 true C 2.177,4.156 2.479,4.406 0.302,0.25 10 true C 3.458,5.656 3.615,5.854 0.156,0.198 10 false E 5.521,5.104 5.677,5.302 0.156,0.198 10 false E 5.146,4.604 5.625,4.823 0.479,0.219 10 true D* 3.344,2.469 3.646,2.719 0.302,0.25 10 true A 3.667,2.448 3.969,2.698 0.302,0.25 10 true A 0.313,6.458 2.948,6.698 2.635,0.24 10 false *: w/o Rear Air Conditioning System

Indication
(Mode)
Front Center Register Side Register Front Footwell Register Rear Face Register Rear Footwell Register Front Defroster
A B C D E F
E264852

Face
E331836

E331836

-
E331838

- -
E264849

Bi-level
E331837

E331837

E331837

E331838

E331838

-
E264850

Foot
E331839

E331839

E331836

E331839

E331837

E331839

E264851

Foot/Def
E331839

E331839

E331837

E331839

E331837

E331838

E264847

Def
- - - - -
E331836


HINT:
·

The size of the circle indicates the proportion of airflow volume.

·

The same system is used for LHD and RHD vehicles.




ii.

for Rear Registers (w/ Rear Air Conditioning System)

E195803E04
3.135,2.052 3.281,2.229 0.146,0.177 10 false A 2.396,1.792 2.542,1.969 0.146,0.177 10 true A 4.51,1.604 4.656,1.781 0.146,0.177 10 true A 3.76,1.344 3.906,1.521 0.146,0.177 10 true A 4.281,2.792 4.427,2.969 0.146,0.177 10 true B 4.375,2.281 4.521,2.458 0.146,0.177 10 true B

Indication
(Mode)
Rear Roof Register Rear Side Register
A B
E264852

Face
E331836

-
E264849

Bi-level
E331838

E331839

E264850

Foot
-
E331837


HINT:

The size of the circle ○ indicates the ratio of airflow volume.





A/C LOCK SENSOR (except 5L-E)


The A/C lock sensor sends A/C pulley speed signals to the air conditioning amplifier assembly. The air conditioning amplifier assembly determines whether the A/C compressor is locked or not by using those signals and engine speed signals.


No. 1 COOLER THERMISTOR


The No. 1 cooler thermistor detects the temperature of the cool air immediately after it passes through the evaporator in the form of resistance changes, and outputs the temperature to the air conditioning amplifier assembly.


BLOWER WITH FAN MOTOR SUB-ASSEMBLY


The blower with fan motor sub-assembly has a built-in blower controller, and is controlled by the air conditioning amplifier assembly using duty control.


AIR CONDITIONING HARNESS ASSEMBLY (BUS CONNECTOR)


a.

A BUS connector is used in the wire harness that connects the servo motor to the air conditioning amplifier assembly.

E195801E02
0.16,0.11 0.915,0.371 0.756,0.260 12 for LHD: 0.16,2.632 0.915,2.893 0.756,0.260 12 for RHD: 0.595,1.002 0.862,1.195 0.267,0.193 10 *1 5.106,0.841 5.373,1.034 0.267,0.193 10 *3 2.916,0.148 3.183,0.341 0.267,0.193 10 *2 6.664,0.995 6.931,1.188 0.267,0.193 10 *4 5.07,1.457 4.96,0.909 4.96,0.909 5.058,0.909 false 6.606,1.544 6.524,1.063 6.524,1.063 6.622,1.063 false 2.837,0.617 2.767,0.216 2.767,0.216 2.865,0.216 false 0.499,1.471 0.429,1.07 0.429,1.07 0.527,1.07 false 2.899,2.471 3.166,2.664 0.267,0.193 10 *5 2.955,2.147 2.734,2.539 2.734,2.539 2.832,2.539 false 3.546,4.108 3.813,4.301 0.267,0.193 10 *1 3.451,4.577 3.38,4.176 3.38,4.176 3.479,4.176 false 0.338,4.029 0.605,4.222 0.267,0.193 10 *2 0.259,4.498 0.189,4.097 0.189,4.097 0.287,4.097 false 1.127,3.571 1.394,3.764 0.267,0.193 10 *5 1.032,4.04 0.961,3.639 0.961,3.639 1.059,3.639 false 5.001,2.621 5.268,2.813 0.267,0.193 10 *3 4.965,3.237 4.855,2.688 4.855,2.688 4.953,2.688 false 6.839,3.98 7.106,4.173 0.267,0.193 10 *4 6.781,4.528 6.699,4.047 6.699,4.047 6.797,4.047 false

Connector Type Connected to
*1: Bus connector Damper servo sub-assembly LH (mode damper servo)
*2: Bus connector Damper servo sub-assembly RH (air mix damper servo)
*3: Bus connector Recirculation damper servo sub-assembly
*4: Bus connector Air conditioning amplifier assembly
*5: Connector No. 1 cooler thermistor


b.

Each BUS connector has a built-in communication/driver IC which communicates with each servo motor connector, actuates the servo motor, and has a position detection function.

E187730E03
4.667,1.031 4.823,0.479 4.823,0.479 4.958,0.479 true 4.531,0.875 4.458,0.531 4.458,0.531 4.198,0.531 true 0.406,2.458 2.938,3.042 2.531,0.583 10 Air Conditioning Amplifier Assembly 1.031,0.865 2.198,1.385 1.167,0.521 10 Communication Circuit 1.417,1.979 1.833,2.26 0.417,0.281 10 CPU 3.146,0.448 4.406,0.813 1.26,0.365 10 BUS Connector 5.01,0.385 7.01,0.698 2.0,0.313 10 Communication/Driver IC 5.75,1.781 6.875,2.208 1.125,0.427 10 Servo Motor



SERVO MOTOR


a.

The pulse pattern type servo motor detects the relative position using 2-bit on/off signals.

The forward and reverse revolutions of this motor are detected using two signals, A and B, which output four types of patterns. The air conditioning amplifier assembly counts the number of pulse patterns in order to determine the stopped position.

E187731E01
2.517,2.977 3.400,3.168 0.883,0.191 10 Pattern Width 4.738,4.038 6.011,4.229 1.273,0.191 10 Pattern Width 2.81° 0.456,0.683 1.811,1.045 1.355,0.362 10 Rotation Direction of Printed Board 5.27,0.335 6.624,0.697 1.355,0.362 10 Rotation Direction of Printed Board 6,2.053 7.129,2.418 1.129,0.365 10 Pattern (Conductive Part) 6.141,1.362 7.056,1.551 0.915,0.189 10 Printed Board 2.605,1.065 3.885,1.235 1.280,0.170 10 Fixed Contact Point 0.34,3.051 0.687,3.220 0.347,0.169 10 GND 3.649,1.879 3.996,2.048 0.347,0.169 10 GND 3.956,2.716 4.116,2.885 0.160,0.169 10 Hi 3.956,2.885 4.130,3.054 0.174,0.169 10 Lo 3.956,3.212 4.116,3.381 0.160,0.169 10 Hi 3.956,3.417 4.130,3.586 0.174,0.169 10 Lo 0.544,2.692 0.672,2.859 0.129,0.167 10 A 0.544,2.331 0.672,2.498 0.129,0.167 10 B 3.875,1.524 4.004,1.691 0.129,0.167 10 A 3.777,2.762 3.906,2.928 0.129,0.167 10 A 3.875,2.228 4.004,2.394 0.129,0.167 10 B 3.777,3.334 3.906,3.501 0.129,0.167 10 B 2.02,2.617 2.02,0.782 2.02,0.782 1.839,0.782 false 4.255,1.594 3.994,1.594 false 4.255,1.941 3.994,1.941 false 4.255,2.291 3.994,2.291 false 4.9,1.149 4.9,0.428 4.9,0.428 5.217,0.428 false 5.845,1.44 6.111,1.44 false 5.874,1.935 6.155,1.935 6.155,1.935 6.155,2.041 false



QUICK HEATER ASSEMBLY (w/ PTC Heater)


a.

General

i.

The PTC heater is located above the heater core in the air conditioner unit.


ii.

The PTC heater consists of a PTC element, aluminum fins and brass plates. When current is applied to the PTC element, it generates heat to warm the air that passes through the unit.

E321145E01
5.128,0.274 5.856,0.456 0.727,0.181 10 Brass Plate 5.578,2.178 6.445,2.359 0.866,0.181 10 Aluminum Fin 1.497,2.364 2.965,2.712 1.468,0.348 10 Quick Heater Assembly (PTC Heater) 4.249,1.006 5.092,1.188 0.843,0.181 10 PTC Element 5.81,1.089 5.14,1.089 false 5.901,0.349 6.065,0.349 6.065,0.349 6.065,0.828 false 6.052,1.727 6.052,2.149 false 2.135,1.91 2.135,2.332 false



b.

PTC Heater Operating Conditions

i.

The on/off operation of the PTC heater is controlled by the air conditioning amplifier assembly in accordance with the engine coolant temperature, ambient temperature, engine speed, air mix setting and electrical load (generator power ratio).

For example, the number of operating PTC heaters varies according to engine coolant temperature as shown in the graph below.

E145149E05
0.233,1.059 2.530,1.252 2.297,0.193 10 Number of PTC Heaters Operating 0.207,0.117 2.195,0.354 1.988,0.237 12 Heater Operation Pattern: 5.795,3.128 6.852,3.541 1.056,0.414 10 Engine Coolant Temperature 2.563,1.5 2.692,1.669 0.129,0.169 10 3 2.563,1.881 2.692,2.050 0.129,0.169 10 2 2.563,2.252 2.692,2.421 0.129,0.169 10 1 2.563,2.643 2.692,2.812 0.129,0.169 10 0 3.12,3.116 3.323,3.285 0.202,0.169 10 73 3.622,3.116 3.824,3.285 0.202,0.169 10 76 4.11,3.116 4.312,3.285 0.202,0.169 10 79 4.594,3.116 4.797,3.285 0.202,0.169 10 82 5.112,3.116 5.314,3.285 0.202,0.169 10 °C 3.078,3.392 3.386,3.560 0.308,0.169 10 163 3.58,3.392 3.869,3.560 0.290,0.169 10 169 4.068,3.392 4.345,3.564 0.278,0.172 10 174 4.552,3.392 4.841,3.560 0.288,0.169 10 180 5.112,3.392 5.399,3.560 0.287,0.169 10 °F




VISCOUS WITH MAGNET CLUTCH HEATER ASSEMBLY (w/ Viscous Heater)


a.

The viscous with magnet clutch heater assembly, which is located on top of the engine, is driven by a drive belt. Pressing the heater switch assembly provided in the instrument panel engages the magnetic clutch, causing the rotor in the viscous with magnet clutch heater assembly to rotate and the silicon oil to mix. The shear heat that is thus generated heats the coolant.


b.

The viscous with magnet clutch heater assembly is controlled in accordance with the engine speed, coolant temperature and ambient temperature. While the power heater is engaged, the engine idling speed is raised to a predetermined value whenever the shift lever is in N or D.



COOLER THERMISTOR (AMBIENT TEMPERATURE SENSOR)


The cooler thermistor (ambient temperature sensor) detects the outside temperature based on changes in the resistance of its built-in thermistor and sends a signal to the air conditioning amplifier assembly.