Home › Engine / Hybrid System › 1KD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2017.08–2020.08
RM27T0E _51 Engine / Hybrid System _053659 1KD-FTV ENGINE CONTROL _0260458 ECD SYSTEM D

1KD-FTV ENGINE CONTROL  ECD SYSTEM  FREEZE FRAME DATA  


DESCRIPTION


The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the air fuel ratio was lean or rich, as well as the other data recorded at the time of a malfunction.

HINT:

If it is impossible to duplicate the problem even though a DTC is stored, confirm the freeze frame data.



A159471E15
1.854,0.323 3,0.542 1.146,0.219 10 false DTC is stored 0.333,2.656 2.615,2.927 2.281,0.271 10 false Freeze frame data recorded 2.708,1.146 3.365,1.344 0.656,0.198 10 false (Seconds) 2.938,1.823 3.344,2.031 0.406,0.208 10 false Time 2.156,1.146 2.385,1.313 0.229,0.167 10 false 0.5 1.333,1.146 1.563,1.313 0.229,0.167 10 false 0.5 0.51,1.146 0.875,1.365 0.365,0.219 10 false 0.5

The ECM records engine conditions in the form of freeze frame data every 0.5 seconds. Using an intelligent tester, 5 separate sets of freeze frame data can be checked.

-

3 data sets from before the DTC was stored

-

1 data set from when the DTC was stored

-

1 data set from after the DTC was stored


These data sets can be used to simulate the condition of the vehicle from around the time of the occurrence of the malfunction. The data may assist in identifying the cause of the malfunction, and in judging whether it was temporary or not.




PENDING FREEZE FRAME DATA


HINT:

Pending freeze frame data is stored when a 2 trip DTC is first detected during the first trip.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Select a DTC in order to display its pending freeze frame data.

HINT:
·

Pending freeze frame data is cleared when any of the following occurs.

-

Using the intelligent tester, the DTCs cleared.

-

The cable is disconnected from the negative (-) battery terminal.

-

40 trips with the engine fully warmed up have been performed after returning to normal. (Pending freeze frame data will not be cleared by only returning the system to normal.)


·

With previous pending freeze frame data stored, if pending freeze frame data is newly stored when a 2 trip DTC is detected in the first trip, the old freeze frame data will be replaced with the new data of the newly detected DTC in the next trip.



A251781E32
0.156,0.104 6.75,0.542 6.594,0.438 10 false When a DTC is detected in both the first and second trips but the system returns to normal from the third trip (2 trip logic DTC): 0.094,1.635 1.188,1.813 1.094,0.177 10 false Ignition Switch 1.302,1.49 2.115,1.781 0.813,0.292 10 false ON 1.302,1.875 1.552,2.052 0.25,0.177 10 false Off 0.104,2.531 1.146,2.896 1.042,0.365 10 false Pending Freeze Frame Data 1.333,2.531 1.781,2.729 0.448,0.198 10 false Stored 1.104,2.885 1.844,3.104 0.74,0.219 10 false Not Stored 0.125,3.708 1.042,4.052 0.917,0.344 10 false Freeze Frame Data 1.292,3.698 1.74,3.896 0.448,0.198 10 false Stored 0.385,4.729 2.01,4.927 1.625,0.198 10 false : Malfunction detected 0.365,5.042 2.083,5.25 1.719,0.208 10 false : Malfunction not detected 2.073,0.885 2.792,1.104 0.719,0.219 10 false (First Trip) 2.823,0.885 3.781,1.125 0.958,0.24 10 false (Second Trip) 3.781,0.885 4.74,1.125 0.958,0.24 10 false (Third Trip) 4.594,0.896 5.552,1.135 0.958,0.24 10 false (Fourth Trip) 1.073,4.021 1.792,4.354 0.719,0.333 10 false Not Stored

A251782E35
0.208,0.219 6.729,0.49 6.521,0.271 10 false When 2 trip DTC is first detected in the first trip and another 2 trip DTC is first detected in the second trip: 2.656,0.813 3.344,1.021 0.688,0.208 10 false (First Trip) 3.521,0.813 4.438,1 0.917,0.188 10 false (Second Trip) 4.573,0.813 5.26,1.021 0.688,0.208 10 false (Third Trip) 5.458,0.813 6.292,1.021 0.833,0.208 10 false (Fourth Trip) 1.635,1.448 2.323,1.656 0.688,0.208 10 false On 1.656,1.771 1.958,1.979 0.302,0.208 10 false Off 1.615,2.365 2.135,2.563 0.521,0.198 10 false Stored 1.625,2.625 2.146,3.021 0.521,0.396 10 false Not Stored 1.604,3.323 2.063,3.521 0.458,0.198 10 false Stored 1.615,3.531 2.135,3.854 0.521,0.323 10 false Not Stored 4.375,2.938 5.063,3.146 0.688,0.208 10 false Uploaded 0.5,1.552 1.417,1.771 0.917,0.219 10 false Ignition Switch 0.49,2.479 1.479,2.854 0.99,0.375 10 false Pending Freeze Frame Data A 0.469,3.417 1.5,3.771 1.031,0.354 10 false Pending Freeze Frame Data B 0.708,4.156 2.875,4.344 2.167,0.188 10 false : Pending malfunction A detected 0.698,4.604 2.885,4.865 2.188,0.26 10 false : Pending malfunction B detected 0.688,5.115 2.51,5.344 1.823,0.229 10 false : No malfunction detected



LIST OF FREEZE FRAME DATA


Tester Display Measurement Item Diagnostic Note
Vehicle Speed Vehicle speed The speed indicated on the speedometer.
Target Idle Engine Speed Target idling speed -
Engine Speed Engine speed -
Calculate Load Calculated load The load calculated by the ECM.
MAF Mass air flow volume If approximately 0.0 g/sec.:
·

The mass air flow meter power source circuit is open or shorted.

·

The VG circuit is open or shorted.

·

The E2G circuit is open.


Atmosphere Pressure Atmospheric pressure -
MAP Absolute pressure inside intake manifold -
Coolant Temp Engine coolant temperature If -40°C (-40°F), the sensor circuit is open.
If 140°C (284°F) or higher, the sensor circuit is shorted.
Intake Air Intake air temperature If -40°C (-40°F), the sensor circuit is open.
If 140°C (284°F) or higher, the sensor circuit is shorted.
Intake Air Temp (Turbo) Intake air temperature after intercooler If -40°C (-40°F), the sensor circuit is open.
If 190°C (374°F) or higher, the sensor circuit is shorted.
Engine Run Time Accumulated engine running time -
Initial Engine Coolant Temp Engine coolant temperature at engine start -
Initial Intake Air Temp Intake air temperature at engine start -
Battery Voltage Battery voltage -
Pre Glow Pre-glow operation -
After Glow After-glow operation -
Accel Position Accelerator pedal position sensor -
Accel Sens. No.1 Volt % Accelerator pedal position No. 1 output voltage -
Accel Sens. No.2 Volt % Accelerator pedal position No. 2 output voltage -
Target Throttle Position Target throttle position -
Actual Throttle Position Actual throttle position -
Diesel Throttle Learn Status Diesel throttle learning status -
Throttle Sensor Volt % Throttle position sensor output voltage -
Throttle Motor DUTY Throttle actuator -
Injection Volume Injection volume -
Inj. FB Vol. for Idle Injection feedback value for idle speed control -
Inj Vol Feedback Learning Injection volume feedback learned value -
Injection Feedback Val #1 Injection volume correction for cylinder 1 -
Injection Feedback Val #2 Injection volume correction for cylinder 2 -
Injection Feedback Val #3 Injection volume correction for cylinder 3 -
Injection Feedback Val #4 Injection volume correction for cylinder 4 -
Pilot 1 Injection Period Pilot 1 injection period -
Pilot 2 Injection Period Pilot 2 injection period -
Main Injection Period Main injection period -
After Injection Period Post injection period -
Pilot 1 Injection Timing Pilot 1 injection timing -
Pilot 2 Injection Timing Pilot 2 injection timing -
Main Injection Timing Main injection timing -
After Injection Timing Post injection timing -
Injector Memory Error State of injector related EEPROM information stored in ECM -
Reju Pilot Quantity Learning Pilot quantity learning prohibition -
Pilot Quantity Learning Pilot quantity learning status -
Target Common Rail Pressure Target common rail pressure -
Common Rail Pressure Common rail pressure -
Fuel Temperature Fuel temperature -
Fuel Return Temp Fuel return temperature -
Intank Fuel Pump In-tank fuel pump status -
Target Pump SCV Current Final pump current target value -
Pump SCV Learning Value Pump current learned value -
Fuel Pressure Relief Valve Fuel pressure relief valve operation prohibition -
Target EGR Position Target EGR valve position -
Actual EGR Valve Pos. Actual EGR valve position -
EGR Close Lrn. Val. EGR valve fully closed position learned value -
EGR Close Lrn. Status EGR valve fully closed position learning status -
EGR Operation Prohibit EGR operation prohibition -
Target Booster Pressure Target booster pressure -
VN Turbo Command VN turbo command -
Actual VN Position Actual VN turbo position -
VN Position Sensor Out VN position sensor output voltage -
VN Motor Duty VN turbo motor duty -
VN Close Learn Value VN turbo fully closed position learned value -
VN Close Learn Status VN turbo fully closed position learning status -
Starter Signal Starter signal -
Power Steering Signal Power steering switch status -
Power Steer. Sig. Record Power steering switch status history -
Neutral Position SW Signal Neutral position switch signal -
Clutch Switch Clutch switch -
Reverse Switch - -
Stop Light Switch Stop light switch -
A/C Signal Air conditioning signal -
Immobiliser Communication Immobiliser communication -
Time after DTC Cleared Cumulative time after DTC cleared -
Distance from DTC Cleared Accumulated distance after DTC cleared -
Warmup Cycle Cleared DTC Warmup cycles after DTC cleared -
TC and TE1 TC and TE1 terminals of DLC3 -
Engine Start Time - -
Engine Speed (Starter Off) - -
Starter Count - -
Run Dist of Previous Trip - -
Electric Duty Feedback Value - -
A/C Duty Feedback Value - -
PS Duty Feedback Value - -
Idle Injection Volume (Min) - -
ACM Inhibit VSV for engine mount status -
Swirl Control Valve VSV VSV for swirl control valve -
ACT VSV A/C cut status for Active Test -
Electric Fan Motor Electric fan motor -
Received MIL from ECT MIL status from ECT -
Shift Position Sig from ECT Shift position from ECT -
A/T Oil Temp from ECT ATF temperature from ECT -
SPD (NO) Output shaft speed -
ECT Lock Up ECT lock-up status -
A/T Oil Temperature 1 ATF temperature sensor value -