Home › Engine / Hybrid System › 1KD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2017.08–2020.08
RM27T0E _51 Engine / Hybrid System _053659 1KD-FTV ENGINE CONTROL _0260458 ECD SYSTEM C

1KD-FTV ENGINE CONTROL  ECD SYSTEM  P0112  Intake Air Temperature Circuit Low Input  P0113  Intake Air Temperature Circuit High Input  


DESCRIPTION

The intake air temperature sensor is built into the mass air flow meter and detects the intake air temperature.

A thermistor built into the sensor changes its resistance value according to the intake air temperature.

The lower the intake air temperature, the higher the thermistor resistance value. The higher the intake air temperature, the lower the thermistor resistance value (See Fig. 1).

The intake air temperature sensor is connected to the ECM.

The 5 V power source voltage from the ECM is applied to the intake air temperature sensor from terminal THA via resistor R.

Resistor R and the intake air temperature sensor are connected in series. When the resistance value of the intake air temperature sensor changes in accordance with the intake air temperature, the voltage at terminal THA also changes. Based on this signal, the ECM increases the fuel injection volume to improve driveability with a cold engine.

A208462E01
1.469,2 1.625,1.76 1.625,1.76 1.771,1.76 false 0.208,0.146 0.906,0.49 0.698,0.344 10 false (Fig. 1) 0.208,0.542 1.313,0.823 1.104,0.281 10 false Resistance kΩ 1.823,1.688 2.656,2.031 0.833,0.344 10 false Acceptable 1.208,4.073 2.521,4.385 1.313,0.313 10 false Temperature °C (°F)

P0112
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 0.5 seconds Short in the IAT sensor for 0.5 seconds (1 trip detection logic).
·

Short in IAT sensor circuit

·

IAT sensor (built into mass air flow meter)

·

ECM



P0113
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 0.5 seconds Open in the IAT sensor for 0.5 seconds (1 trip detection logic).
·

Open in IAT sensor circuit

·

IAT sensor (built into mass air flow meter)

·

ECM



Related Data List
DTC No. Data List
P0112 Intake Air
P0113

HINT:
·

If DTC P0112 and/or P0113 is stored, the following symptoms may appear:

-

Misfire

-

Combustion noise

-

Black smoke

-

White smoke

-

Lack of power


·

When DTC P0112 or P0113 is stored, check the intake air temperature by entering the following menus: Powertrain / Engine and ECT / Data List / Intake Air.

Reference
Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
140°C (284°F) or higher Short circuit



WIRING DIAGRAM

A210074E13
0.438,2.076 2.455,2.443 2.016,0.366 10 Intake Air Temperature Sensor (Built into Mass Air Flow Meter) 2.054,0.662 2.349,0.843 0.295,0.181 10 THA 2.163,1.244 2.350,1.425 0.187,0.181 10 E2 5.865,2.411 6.252,2.585 0.387,0.174 10 ECM 6.261,0.218 6.487,0.399 0.225,0.181 10 5 V 5.563,0.655 5.858,0.836 0.295,0.181 10 THA 5.563,1.263 5.950,1.445 0.388,0.181 10 ETHA 6.175,0.536 6.331,0.717 0.156,0.181 10 R 2.459,0.85 2.578,1.035 0.119,0.185 10 1 2.459,1.47 2.575,1.651 0.115,0.181 10 2 5.361,0.655 5.470,0.812 0.109,0.157 10 6 5.274,1.263 5.479,1.445 0.205,0.181 10 12 0.438,1.908 0.744,2.079 0.305,0.171 10 C33 5.865,2.261 6.178,2.407 0.313,0.147 10 C90

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (INTAKE AIR TEMPERATURE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.


d.

Read the value.

OK:

Same as actual intake air temperature


Result
Result Proceed to
-40°C (-40°F) A
140°C (284°F) or higher B
OK (same as actual intake air temperature) C

HINT:
·

If there is an open circuit, the tester indicates -40°C (-40°F).

·

If there is a short circuit, the tester indicates 140°C (284°F) or higher.





A

2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)

B

4.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)

C

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)
a.
U169085E02
1.333,3.479 1.125,4.031 true 1.552,3.479 1.802,4.01 true 1.771,4.052 2,4.25 0.229,0.198 10 false E2 2.458,1.021 2.792,1.219 0.333,0.198 10 false THA 0.969,4.052 1.302,4.25 0.333,0.198 10 false THA 2.469,1.49 2.854,1.646 0.385,0.156 10 false ETHA 0.792,0.146 1.083,0.406 0.292,0.26 10 false *1 2.646,0.146 2.917,0.375 0.271,0.229 10 false *2 0.135,2.188 0.438,2.438 0.302,0.25 10 false *a 0.354,3.354 0.74,3.583 0.385,0.229 10 false C33

Disconnect the mass air flow meter connector.


b.

Connect terminals 1 (THA) and 2 (E2) of the mass air flow meter wire harness side connector.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON and turn the tester on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.


f.

Read the value.

OK:

140°C (284°F) or higher


Text in Illustration
*1 Mass air flow meter
*2 ECM
*a Front view of wire harness connector
(to mass air flow meter)


g.

Reconnect the mass air flow meter connector.



OK

7.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE MASS AIR FLOW METER.

NG

3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the mass air flow meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C33-1 (THA) - C90-6 (THA) Always Below 1 Ω
C33-2 (E2) - C90-12 (ETHA) Always Below 1 Ω



d.

Reconnect the mass air flow meter connector.


e.

Reconnect the ECM connector.



OK

9.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM.

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)
a.
A372459E01
2.438,1.021 2.896,1.219 0.458,0.198 10 false THA 2.438,1.51 2.896,1.708 0.458,0.198 10 false ETHA 2.594,0.229 2.906,0.427 0.313,0.198 10 false *2 0.74,0.417 1.052,0.615 0.313,0.198 10 false *1

Disconnect the mass air flow meter connector.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON and turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.


e.

Read the value.

OK:

-40°C (-40°F)


Text in Illustration
*1 Mass air flow meter
*2 ECM


f.

Reconnect the mass air flow meter connector.



OK

10.REPLACE MASS AIR FLOW METER

NG

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the mass air flow meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C33-1 (THA) or C90-6 (THA) - Body ground Always 10 kΩ or higher



d.

Reconnect the mass air flow meter connector.


e.

Reconnect the ECM connector.



OK

6.REPLACE ECM

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.REPLACE ECM

NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE MASS AIR FLOW METER.

NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM.

NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPLACE MASS AIR FLOW METER

NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.



c.

Turn the ignition switch to ON for 1 second.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Confirm that the DTC is not output again.



NEXT

END