Home › Engine / Hybrid System › 1KD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2017.08–2020.08
RM27T0E _51 Engine / Hybrid System _053659 1KD-FTV ENGINE CONTROL _0260458 ECD SYSTEM C

1KD-FTV ENGINE CONTROL  ECD SYSTEM  P0180  Fuel Temperature Sensor "A" Circuit  P0182  Fuel Temperature Sensor "A" Circuit Low Input  P0183  Fuel Temperature Sensor "A" Circuit High Input  


DESCRIPTION

The fuel temperature sensor monitors the fuel temperature. The fuel temperature sensor has a thermistor that varies its resistance depending on the fuel temperature. When the fuel temperature is low, the resistance of the thermistor is high. When the temperature is high, the resistance is low. The variations of resistance are communicated to the ECM as changes of voltage (See Fig. 1).

The fuel temperature sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the fuel temperature sensor from terminal THF via resistor R.

Resistor R and the fuel temperature sensor are connected in series. When the resistance value of the fuel temperature sensor changes due to a change in fuel temperature, the voltage at terminal THF also changes. Based on this signal, the ECM corrects the pressure control compensation of the fuel supply pump assembly.

A208462E01
1.469,2 1.625,1.76 1.625,1.76 1.771,1.76 false 0.208,0.146 0.906,0.49 0.698,0.344 10 false (Fig. 1) 0.208,0.542 1.313,0.823 1.104,0.281 10 false Resistance kΩ 1.823,1.688 2.656,2.031 0.833,0.344 10 false Acceptable 1.208,4.073 2.521,4.385 1.313,0.313 10 false Temperature °C (°F)

P0180
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 0.5 seconds Open or short in the fuel temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Open or short in fuel temperature sensor circuit

·

Fuel temperature sensor

·

ECM



P0182
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 0.5 seconds Short in the fuel temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Short in fuel temperature sensor circuit

·

Fuel temperature sensor

·

ECM



P0183
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 0.5 seconds Open in the fuel temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Open in fuel temperature sensor circuit

·

Fuel temperature sensor

·

ECM



Related Data List
DTC No. Data List
P0180 Fuel Temp
P0182
P0183

HINT:

If DTC P0180, P0182 and/or P0183 is stored, the following symptoms may appear:

-

Misfire

-

Combustion noise

-

Black smoke

-

Lack of power




WIRING DIAGRAM

A210074E15
0.638,2.136 2.284,2.298 1.647,0.163 10 Fuel Temperature Sensor 5.957,2.427 6.357,2.601 0.400,0.174 10 ECM 6.253,0.213 6.478,0.394 0.225,0.181 10 5 V 5.554,0.65 5.913,0.832 0.358,0.181 10 THF 5.554,1.259 6.017,1.440 0.463,0.181 10 ETHF 6.166,0.531 6.322,0.713 0.156,0.181 10 R 2.451,1.28 2.570,1.465 0.119,0.185 10 1 2.451,0.667 2.566,0.848 0.115,0.181 10 2 5.341,0.65 5.457,0.807 0.116,0.157 10 4 5.252,1.273 5.456,1.454 0.205,0.181 10 10 0.638,1.949 0.915,2.131 0.277,0.183 10 C85 5.957,2.26 6.252,2.407 0.295,0.147 10 C90

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (FUEL TEMPERATURE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Temp.


d.

Read the value.

OK:

Same as the actual fuel temperature


Result
Result Proceed to
-40°C (-40°F) A
140°C (284°F) or higher B
OK (Same as actual fuel temperature) C

HINT:
·

If there is an open circuit, the tester indicates -40°C (-40°F).

·

If there is a short circuit, the tester indicates 140°C (284°F) or higher.





A

2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)

B

6.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)

C

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)
a.
U169128E02
0.802,0.156 1.01,0.302 0.208,0.146 10 false *1 2.625,0.125 2.792,0.292 0.167,0.167 10 false *2 0.594,2.635 0.792,2.823 0.198,0.188 10 false *a 2.406,1.031 2.719,1.177 0.313,0.146 10 false THF 2.385,1.51 2.781,1.667 0.396,0.156 10 false ETHF 0.635,3.406 0.938,3.563 0.302,0.156 10 false C85

Disconnect the fuel temperature sensor connector.


b.

Connect terminals 2 and 1 of the fuel temperature sensor connector.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON and turn the tester on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Temp.


f.

Read the value.

OK:

140°C (284°F) or higher


Text in Illustration
*1 Fuel temperature sensor
*2 ECM
*a Front view of wire harness connector
(to fuel temperature sensor)


g.

Reconnect the fuel temperature sensor connector.



OK

3.REPLACE FUEL TEMPERATURE SENSOR

NG

4.CHECK HARNESS AND CONNECTOR (FUEL TEMPERATURE SENSOR - ECM)
3.REPLACE FUEL TEMPERATURE SENSOR
a.

Replace the fuel temperature sensor (See page Engine / Hybrid System>1KD-FTV (FUEL)>FUEL TEMPERATURE SENSOR>REMOVAL).



NEXT

10.BLEED AIR FROM FUEL SYSTEM
4.CHECK HARNESS AND CONNECTOR (FUEL TEMPERATURE SENSOR - ECM)
a.

Disconnect the fuel temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C85-2 - C90-4 (THF) Always Below 1 Ω
C85-1 - C90-10 (ETHF) Always Below 1 Ω



d.

Reconnect the fuel temperature sensor connector.


e.

Reconnect the ECM connector.



OK

5.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM.

NG

12.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM.

NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)
a.
A204586E01
0.787,0.15 0.993,0.302 0.207,0.151 10 *1 2.618,0.122 2.786,0.289 0.167,0.167 10 *2 2.391,0.97 2.699,1.121 0.309,0.151 10 THF 2.373,1.438 2.765,1.594 0.392,0.156 10 ETHF

Disconnect the fuel temperature sensor connector.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON and turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Temp.


e.

Read the value.

OK:

-40°C (-40°F)


Text in Illustration
*1 Fuel temperature sensor
*2 ECM


f.

Reconnect the fuel temperature sensor connector.



OK

7.REPLACE FUEL TEMPERATURE SENSOR

NG

8.CHECK HARNESS AND CONNECTOR (FUEL TEMPERATURE SENSOR - ECM)
7.REPLACE FUEL TEMPERATURE SENSOR
a.

Replace the fuel temperature sensor (See page Engine / Hybrid System>1KD-FTV (FUEL)>FUEL TEMPERATURE SENSOR>REMOVAL).



NEXT

10.BLEED AIR FROM FUEL SYSTEM
8.CHECK HARNESS AND CONNECTOR (FUEL TEMPERATURE SENSOR - ECM)
a.

Disconnect the fuel temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C85-2 or C90-4 (THF) - Body ground Always 10 kΩ or higher



d.

Reconnect the fuel temperature sensor connector.


e.

Reconnect the ECM connector.



OK

9.REPLACE ECM

NG

12.REPAIR OR REPLACE HARNESS OR CONNECTOR
9.REPLACE ECM

NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system (See page Engine / Hybrid System>1KD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION).



NEXT

11.PERFORM FUEL SUPPLY PUMP INITIALIZATION
11.PERFORM FUEL SUPPLY PUMP INITIALIZATION
a.

Perform fuel supply pump initialization (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.



c.

Turn the ignition switch to ON for 1 second or more.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Confirm that the DTC is not output again.



NEXT

END