Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › 2017.08–2020.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0325854 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  Bus Buffer ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Bus Buffer ECU Communication Stop Mode Any of the following conditions are met:
·

"Accessory Gateway" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Bus Buffer ECU Communication Stop Mode" in "DTC Combination Table"

Click here(Click here)


·

Bus buffer ECU CAN branch wire or connector

·

Bus buffer ECU



WIRING DIAGRAM

C345892E55
0.365,2.615 2.344,2.823 1.979,0.208 10 false No. 5 CAN Junction Connector 4.385,2.729 6.792,2.927 2.406,0.198 10 false Option Connector (Bus Buffer ECU) 5.458,1.677 6.417,2.063 0.958,0.385 10 false Dealer-installed Option 4.396,2.542 4.813,2.719 0.417,0.177 10 false G199 4.479,1.5 4.99,1.677 0.51,0.177 10 false CAN+ 4.5,2.042 5.01,2.219 0.51,0.177 10 false CAN- 4.26,1.417 4.448,1.583 0.188,0.167 10 false 2 4.26,1.979 4.448,2.146 0.188,0.167 10 false 1 0.365,2.448 0.76,2.635 0.396,0.188 10 false G289 1.771,1.958 2.073,2.135 0.302,0.177 10 false 16 1.771,1.417 2.073,1.594 0.302,0.177 10 false 5

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

DTC check procedure: Turn the ignition switch to ON, wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (BUS BUFFER ECU CAN BRANCH WIRE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C379578C04
1.458,0.135 1.896,0.344 0.438,0.208 1.99,0.969 2.354,0.635 2.354,0.635 2.531,0.635 true 1.833,1.094 2.354,1.573 2.354,1.573 2.531,1.573 true 0.083,0.094 0.396,0.292 0.313,0.198 10 false *a 1.51,0.167 2,0.385 0.49,0.219 10 false G199 2.552,0.552 3.063,0.802 0.51,0.25 10 false CAN- 2.563,1.479 3.031,1.677 0.469,0.198 10 false CAN+
*a Front view of wire harness connector
(to Bus Buffer ECU)


Disconnect the bus buffer ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G199-2 (CAN+) - G199-1 (CAN-) Cable disconnected from negative (-) battery terminal 54 to 69 Ω




OK

REPLACE BUS BUFFER ECU

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR