Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › 2017.08–2020.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0325854 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  Check Bus 3 Lines for Short Circuit  


DESCRIPTION

There may be a short circuit between the bus 3 CAN main wires and/or CAN branch wires when the resistance between terminals 6 (CA3H) and 21 (CA3L) of the central gateway ECU (network gateway ECU) is below 54 Ω.

Symptom Trouble Area

*1: w/ Navigation System

*2: w/ Audio and Visual System

*3: w/ Telematics Transceiver

*4: w/ Bus Buffer ECU

·

Resistance between terminals 6 (CA3H) and 21 (CA3L) of central gateway ECU (network gateway ECU) is below 54 Ω.

·

Resistance between terminals 19 (CAYH) and 20 (CAYL) of central gateway ECU (network gateway ECU) is below 54 Ω.


·

Short in CAN main bus lines

·

Short in CAN branch lines

·

Central gateway ECU (network gateway ECU)

·

Navigation receiver assembly (EMVN ECU)*1

·

Radio and display receiver assembly (EMVN ECU)*2

·

Telematics transceiver*3

·

Bus buffer ECU*4

·

No. 5 CAN junction connector



WIRING DIAGRAM

C382805E01
0.177,2.375 0.635,2.573 0.458,0.198 10 false H56 0.135,2.573 3.063,2.938 2.927,0.365 10 false Navigation Receiver Assembly (EMVN ECU)*2 0.875,1.833 1.333,2.031 0.458,0.198 10 false CANH 0.906,2.219 1.365,2.417 0.458,0.198 10 false CANL 1.385,1.719 1.844,1.917 0.458,0.198 10 false 9 1.385,2.104 1.844,2.302 0.458,0.198 10 false 10 2.01,1.729 2.469,1.927 0.458,0.198 10 false *2 2.01,2.104 2.469,2.302 0.458,0.198 10 false *2 1.99,0.333 2.448,0.531 0.458,0.198 10 false *1 2,0.708 2.458,0.906 0.458,0.198 10 false *1 0.083,0.958 0.542,1.156 0.458,0.198 10 false H51 0.073,1.167 2.406,1.5 2.333,0.333 10 false Radio and Display Receiver Assembly (EMVN ECU)*1 0.854,0.438 1.313,0.635 0.458,0.198 10 false CANH 0.906,0.813 1.365,1.01 0.458,0.198 10 false CANL 1.385,0.344 1.844,0.542 0.458,0.198 10 false 9 1.385,0.74 1.844,0.938 0.458,0.198 10 false 10 0.177,3.906 0.677,4.104 0.5,0.198 10 false G187 0.875,3.344 1.333,3.542 0.458,0.198 10 false CANP 0.865,3.76 1.323,3.958 0.458,0.198 10 false CANN 1.365,3.24 1.823,3.438 0.458,0.198 10 false 15 1.375,3.646 1.833,3.844 0.458,0.198 10 false 16 0.302,4.146 3.229,4.51 2.927,0.365 10 false Telematics Transceiver*3 0.125,5.677 0.583,5.875 0.458,0.198 10 false G199 0.135,5.854 3.063,6.219 2.927,0.365 10 false Bus Buffer ECU*4 0.875,5.125 1.333,5.323 0.458,0.198 10 false CAN+ 0.896,5.521 1.354,5.719 0.458,0.198 10 false CAN- 1.396,5.375 1.854,5.573 0.458,0.198 10 false 1 1.385,4.979 1.844,5.177 0.458,0.198 10 false 2 3.552,5 4.01,5.198 0.458,0.198 10 false 5 3.5,5.385 3.958,5.583 0.458,0.198 10 false 16 3.563,3.24 4.021,3.438 0.458,0.198 10 false 4 3.49,3.667 3.948,3.865 0.458,0.198 10 false 15 3.573,0.302 4.031,0.5 0.458,0.198 10 false 3 3.5,0.708 3.958,0.906 0.458,0.198 10 false 14 4.51,0.313 4.969,0.51 0.458,0.198 10 false 1 4.521,0.698 4.979,0.896 0.458,0.198 10 false 12 4.51,4.979 4.969,5.177 0.458,0.198 10 false 2 4.5,5.406 4.958,5.604 0.458,0.198 10 false 13 5.698,0.302 6.156,0.5 0.458,0.198 10 false 6 5.656,0.729 6.115,0.927 0.458,0.198 10 false 21 5.688,5.021 6.146,5.219 0.458,0.198 10 false 19 5.667,5.396 6.125,5.594 0.458,0.198 10 false 20 5.979,0.333 6.438,0.531 0.458,0.198 10 false CA3H 5.969,0.969 6.427,1.167 0.458,0.198 10 false CA3L 5.938,5.01 6.396,5.208 0.458,0.198 10 false CAYH 5.958,5.656 6.417,5.854 0.458,0.198 10 false CAYL 5.156,5.802 5.615,6 0.458,0.198 10 false G229 5.177,5.948 7.156,6.396 1.979,0.448 10 false Central Gateway ECU (Network Gateway ECU) 3,5.76 3.458,5.958 0.458,0.198 10 false G289 3.01,5.906 4.948,6.135 1.938,0.229 10 false No. 5 CAN Junction Connector 0.083,6.229 2.479,6.51 2.396,0.281 10 false *1: w/ Audio and Visual System 0.073,6.5 2.469,6.781 2.396,0.281 10 false *2: w/ Navigation System 1.719,6.521 4.115,6.802 2.396,0.281 10 false *3: w/ Telematics Transceiver 3.719,6.521 6.115,6.802 2.396,0.281 10 false *4: w/ Bus Buffer ECU

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from negative (-) battery terminal.


b.
C382809C02
0.135,1.49 0.521,1.719 0.385,0.229 0.708,0.75 0.875,0.75 0.875,0.75 0.875,1.583 true 0.708,2.604 0.875,2.604 0.875,2.604 0.875,1.938 true 1.375,0.417 1.208,0.417 1.208,0.417 1.208,1.583 true 0.854,0.5 1.021,0.5 1.021,0.5 1.021,1.583 true 1.542,0.615 1.375,0.615 1.375,0.615 1.375,1.583 true 1.688,0.833 1.521,0.833 1.521,0.833 1.521,1.583 true 0.865,2.854 1.031,2.854 1.031,2.854 1.031,1.938 true 1.385,3 1.219,3 1.219,3 1.219,1.917 true 1.531,2.781 1.365,2.781 1.365,2.781 1.365,1.948 true 1.708,2.542 1.542,2.542 1.542,2.542 1.542,1.958 true 0.094,0.104 0.406,0.302 0.313,0.198 10 false *a 0.156,1.51 0.531,1.708 0.375,0.198 10 false G289 0.146,0.677 0.708,0.948 0.563,0.271 10 false CANH*b 0.188,2.521 0.75,2.792 0.563,0.271 10 false CANL*b 0.333,0.427 0.896,0.698 0.563,0.271 10 false CANH*c 0.302,2.771 0.865,3.042 0.563,0.271 10 false CANL*c 1.448,0.344 2.01,0.615 0.563,0.271 10 false CANH*d 1.583,0.542 2.146,0.813 0.563,0.271 10 false CANH*e 1.74,0.76 2.302,1.031 0.563,0.271 10 false CANH*f 1.438,2.917 2,3.188 0.563,0.271 10 false CANL*d 1.583,2.719 2.146,2.99 0.563,0.271 10 false CANL*e 1.76,2.458 2.323,2.729 0.563,0.271 10 false CANL*f
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)
*c to Central Gateway ECU (Network Gateway ECU)
*d
·

to Navigation Receiver Assembly (EMVN ECU) (w/ Navigation System)

·

to Radio and Display Receiver Assembly (EMVN ECU) (w/ Audio and Visual System)


*e to Telematics Transceiver (w/ Telematics Transceiver)
*f to Bus Buffer ECU (w/ Bus Buffer ECU)


Disconnect the No. 5 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

*1: w/ Navigation System

*2: w/ Audio and Visual System

*3: w/ Telematics Transceiver

*4: w/ Bus Buffer ECU

G289-1 (CANH) - G289-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)
G289-2 (CANH) - G289-13 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)
G289-3 (CANH) - G289-14 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher
·

Navigation receiver assembly (EMVN ECU)*1

·

Radio and display receiver assembly (EMVN ECU)*2


G289-4 (CANH) - G289-15 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Telematics transceiver*3
G289-5 (CANH) - G289-16 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Bus buffer ECU*4



Result:
Result Proceed to
OK A
NG (Central gateway ECU [network gateway ECU] CAN main wire) B
NG (Wire to ECU or sensor) C



A

REPLACE NO. 5 CAN JUNCTION CONNECTOR

B

2.CONNECT CONNECTOR

C

4.CHECK FOR SHORT IN CAN BUS WIRES (ECU, SENSOR)
2.CONNECT CONNECTOR
a.

Reconnect the G289 No. 5 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

3.CHECK FOR SHORT IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 5 CAN JUNCTION CONNECTOR)
3.CHECK FOR SHORT IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 5 CAN JUNCTION CONNECTOR)
a.
C379599C05
1.49,0.063 1.917,0.302 0.427,0.24 1.177,1.75 1.406,1.75 1.406,1.75 1.917,1.198 true 1.292,1.927 1.521,1.927 1.521,1.927 2.052,1.208 true 2.563,1.885 2.396,1.885 2.396,1.885 2.188,1.208 true 2.615,0.323 2.448,0.323 2.448,0.323 2.292,0.938 true 1.552,0.083 2.01,0.281 0.458,0.198 10 false G229 0.76,1.667 1.219,1.865 0.458,0.198 10 false CAYH 0.885,1.854 1.344,2.052 0.458,0.198 10 false CAYL 2.615,1.833 3.073,2.031 0.458,0.198 10 false CA3L 2.656,0.25 3.115,0.448 0.458,0.198 10 false CA3H 0.052,0.052 0.51,0.25 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU])


Disconnect the central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G229-6 (CA3H) - G229-21 (CA3L) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G229-19 (CAYH) - G229-20 (CAYL)



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 5 CAN JUNCTION CONNECTOR)

4.CHECK FOR SHORT IN CAN BUS WIRES (ECU, SENSOR)
a.
C347660C11
1.458,0.167 1.958,0.417 0.5,0.25 0.969,0.458 1.375,0.979 true 1.021,1.74 1.417,1.115 true 0.125,0.094 0.438,0.25 0.313,0.156 10 false *a 0.573,0.396 1.188,0.594 0.615,0.198 10 false CA3H 0.656,1.667 1.271,1.865 0.615,0.198 10 false CA3L 1.531,0.208 2.146,0.406 0.615,0.198 10 false G229
*a Component with harness connected
(Central Gateway ECU [Network Gateway ECU])


Reconnect the wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short circuited CAN branch wire is connected.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G229-6 (CA3H) - G229-21 (CA3L) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


HINT:
·

If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

·

If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short in the wire harness and repair or replace the wire harness or connector if necessary.




Result:
Proceed to
OK
NG



OK

REPLACE ECU OR SENSOR

NG

REPLACE CORRESPONDING ECU OR SENSOR