There may be a short circuit between one of the CAN bus wires and +B when no resistance exists between terminal 6 (CA3H) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 21 (CA3L) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3.
| Symptom | Trouble Area |
|---|---|
|
*1: w/ Navigation System *2: w/ Audio and Visual System *3: w/ Telematics Transceiver *4: w/ Bus Buffer ECU |
|
·
No resistance exists between terminal 6 (CA3H) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 21 (CA3L) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3. ·
No resistance exists between terminal 19 (CAYH) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 20 (CAYL) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3. |
·
Short to +B in CAN main bus line ·
Short to +B in CAN branch line ·
Central gateway ECU (network gateway ECU) ·
Navigation receiver assembly (EMVN ECU)*1 ·
Radio and display receiver assembly (EMVN ECU)*2 ·
Telematics transceiver*3 ·
Bus buffer ECU*4 ·
No. 5 CAN junction connector |
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Some parts must be initialized and set when replacing or removing and installing parts.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM
Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
Disconnect the cable from negative (-) battery terminal.
| *a | Front view of wire harness connector
(to No. 5 CAN Junction Connector) |
| *b | Front view of DLC3 |
| *c | to Central Gateway ECU (Network Gateway ECU) |
| *d | to Central Gateway ECU (Network Gateway ECU) |
| *e | ·
to Navigation Receiver Assembly (EMVN ECU) (w/ Navigation System) ·
to Radio and Display Receiver Assembly (EMVN ECU) (w/ Audio and Visual System) |
| *f | to Telematics Transceiver (w/ Telematics Transceiver) |
| *g | to Bus Buffer ECU (w/ Bus Buffer ECU) |
Disconnect the No. 5 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
|
*1: w/ Navigation System *2: w/ Audio and Visual System *3: w/ Telematics Transceiver *4: w/ Bus Buffer ECU |
|||
| G289-1 (CANH) - G48-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Central gateway ECU (network gateway ECU) |
| G289-12 (CANL) - G48-16 (BAT) | |||
| G289-2 (CANH) - G48-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Central gateway ECU (network gateway ECU) |
| G289-13 (CANL) - G48-16 (BAT) | |||
| G289-3 (CANH) - G48-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | ·
Navigation receiver assembly (EMVN ECU)*1 ·
Radio and display receiver assembly (EMVN ECU)*2 |
| G289-14 (CANL) - G48-16 (BAT) | |||
| G289-4 (CANH) - G48-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Telematics transceiver*3 |
| G289-15 (CANL) - G48-16 (BAT) | |||
| G289-5 (CANH) - G48-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Bus buffer ECU*4 |
| G289-16 (CANL) - G48-16 (BAT) | |||
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Central gateway ECU [network gateway ECU] CAN main wire) | B |
| NG (Wire to ECU or sensor) | C |
A
B
C
Reconnect the G289 No. 5 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU]) |
| *b | Front view of DLC3 |
Disconnect the central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G229-6 (CA3H) - G48-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G229-21 (CA3L) - G48-16 (BAT) | ||
| G229-19 (CAYH) - G48-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G229-20 (CAYL) - G48-16 (BAT) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the wire harness connectors.
| *a | Component with harness connected
(Central Gateway ECU [Network Gateway ECU]) |
| *b | Front view of DLC3 |
Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short to +B is connected.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G229-6 (CA3H) - G48-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G229-21 (CA3L) - G48-16 (BAT) |
If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.
If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short to +B in the wire harness and repair or replace the wire harness or connector if necessary.
| Proceed to |
|---|
| OK |
| NG |
OK
NG