Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › 2017.08–2020.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0325854 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  Navigation ECU Communication Stop Mode  


DESCRIPTION

Detection Condition Symptoms Trouble Area
Navigation ECU Communication Stop Mode Any of the following conditions are met:
·

"Display and Navigation (AVN)" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Navigation ECU Communication Stop Mode" in "DTC Combination Table"

Click here(Click here)


·

Navigation receiver assembly CAN branch wire or connector

·

Power source circuit of navigation receiver assembly

·

Navigation receiver assembly ground circuit

·

Navigation receiver assembly



WIRING DIAGRAM

C289528E13
5.229,1.167 5.406,1.333 0.177,0.167 10 false 10 5.24,0.583 5.344,0.74 0.104,0.156 10 false 9 5.26,3.917 5.365,4.052 0.104,0.135 10 false 7 5.167,0.833 5.51,1.01 0.344,0.177 10 false H56 5.177,1.417 5.5,1.594 0.323,0.177 10 false H56 5.167,4.167 5.51,4.323 0.344,0.156 10 false H54 5.583,1.396 5.99,1.563 0.406,0.167 10 false CANL 5.573,0.833 6.021,1 0.448,0.167 10 false CANH 5.594,4.156 6.01,4.344 0.417,0.188 10 false GND1 0.365,1.76 0.844,1.927 0.479,0.167 10 false G289 0.375,1.906 2.5,2.125 2.125,0.219 10 false No. 5 CAN Junction Connector 1.594,1.302 1.802,1.479 0.208,0.177 10 false 14 1.615,0.75 1.792,0.917 0.177,0.167 10 false 3 5.177,2.417 5.5,2.583 0.323,0.167 10 false H54 5.25,2.156 5.344,2.323 0.094,0.167 10 false 4 5.594,2.417 5.875,2.604 0.281,0.188 10 false +B1 2.25,2.406 3.198,2.677 0.948,0.271 10 false from Battery 3.906,2.271 4.698,2.51 0.792,0.24 10 false RAD NO.1 5.271,2.74 5.385,2.906 0.115,0.167 10 false 3 5.177,3 5.5,3.156 0.323,0.156 10 false H54 5.604,3.01 5.99,3.177 0.385,0.167 10 false ACC1 2.042,2.958 3.281,3.271 1.24,0.313 10 false from ACC Relay 4.073,2.823 4.656,3.073 0.583,0.25 10 false ACC 5.271,3.344 5.375,3.479 0.104,0.135 10 false 1 5.177,3.583 5.5,3.76 0.323,0.177 10 false H56 5.583,3.583 5.781,3.75 0.198,0.167 10 false IG 1.792,3.573 3.375,3.844 1.583,0.271 10 false from IG NO.1 Relay 3.833,3.427 4.781,3.646 0.948,0.219 10 false ECU-IG NO.2 5.021,4.927 6.927,5.135 1.906,0.208 10 false Navigation Receiver Assembly

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

DTC check procedure: Turn the ignition switch to ON, wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (NAVIGATION RECEIVER ASSEMBLY BRANCH WIRE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
U170266C01
2.042,1.302 2.26,1.823 2.26,1.823 2.365,1.823 true 1.906,1.302 1.688,1.823 1.688,1.823 1.583,1.823 true 0.083,0.083 0.292,0.25 0.208,0.167 10 false *a 1.583,0.375 2.031,0.625 0.448,0.25 10 false H56 1.156,1.75 1.677,1.969 0.521,0.219 10 false CANH 2.406,1.729 2.948,1.958 0.542,0.229 10 false CANL
*a Front view of wire harness connector
(to Navigation Receiver Assembly)


Disconnect the navigation receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H56-9 (CANH) - H56-10 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω




OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
U170331C01
2.01,0.865 2.302,0.552 2.302,0.552 2.406,0.552 true 2.188,0.979 2.385,1.188 2.385,1.188 2.49,1.188 true 1.604,1.156 1.354,1.458 1.354,1.458 1.25,1.458 true 0.646,2.427 0.781,2.427 0.781,2.427 0.979,2.604 true 0.063,0.063 0.271,0.229 0.208,0.167 10 false *a 0.448,2.354 0.698,2.594 0.25,0.24 10 false IG 0.792,1.385 1.323,1.604 0.531,0.219 10 false GND1 2.5,1.115 3,1.354 0.5,0.24 10 false +B1 2.427,0.479 2.938,0.719 0.51,0.24 10 false ACC1 1.583,1.813 1.969,2.031 0.385,0.219 10 false H56 1.583,0.219 2.031,0.469 0.448,0.25 10 false H54
*a Front view of wire harness connector
(to Navigation Receiver Assembly)


Disconnect the navigation receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H54-7 (GND1) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H54-4 (+B1) - Body ground Always 11 to 14 V
H54-3 (ACC1) - Body ground Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
H56-1 (IG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)