Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › 2017.08–2020.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0325854 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  Front Active Stabilizer Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Front Active Stabilizer Control ECU Communication Stop Mode Any of the following conditions are met:
·

"Stabilizer Control (KDSS)" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Front Active Stabilizer Control ECU Communication Stop Mode" in "DTC Combination Table"

Click here(Click here)


·

Stabilizer control ECU CAN branch wire or connector

·

Power source circuit of stabilizer control ECU

·

Stabilizer control ECU ground circuit

·

Stabilizer control ECU



WIRING DIAGRAM

C369099E09
5.385,3.833 7.073,4.208 1.688,0.375 10 false Stabilizer Control ECU 5.385,3.677 5.76,3.854 0.375,0.177 10 false G123 5.594,3.188 5.969,3.365 0.375,0.177 10 false GND 5.604,2.604 5.979,2.781 0.375,0.177 10 false IG 5.615,1.135 6.073,1.333 0.458,0.198 10 false CANH 5.604,1.729 6.063,1.927 0.458,0.198 10 false CANL 5.344,1.01 5.583,1.24 0.24,0.229 10 false 29 5.344,1.594 5.656,1.833 0.313,0.24 10 false 28 5.333,3.063 5.594,3.26 0.26,0.198 10 false 22 5.344,2.469 5.625,2.698 0.281,0.229 10 false 24 3.26,2.448 4.49,2.646 1.229,0.198 10 false KDSS 1.135,2.573 2.521,2.938 1.385,0.365 10 false from IG NO.3 Relay 0.198,2.094 2.427,2.396 2.229,0.302 10 false No. 3 CAN Junction Connector 0.198,1.917 0.74,2.125 0.542,0.208 10 false G287 1.667,1 1.854,1.177 0.188,0.177 10 false 2 1.656,1.573 1.969,1.802 0.313,0.229 10 false 12

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

DTC check procedure: Turn the ignition switch to ON, wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (STABILIZER CONTROL ECU BRANCH WIRE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
U148444C01
1.208,1.573 0.823,1.24 0.823,1.24 0.729,1.24 true 1.292,1.615 0.896,1.927 0.896,1.927 0.813,1.927 true 0.302,1.167 0.729,1.313 0.427,0.146 10 false CANH 0.427,1.844 0.854,1.99 0.427,0.146 10 false CANL 0.115,0.031 0.542,0.177 0.427,0.146 10 false *a 0.24,1.469 0.615,1.615 0.375,0.146 10 false G123
*a Rear view of wire harness connector
(to Stabilizer Control ECU)


Disconnect the stabilizer control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G123-29 (CANH) - G123-28 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
U148444C02
1.625,1.615 1.271,1.979 1.271,1.979 1.188,1.979 true 2.219,1.99 2.094,1.99 2.094,1.99 1.792,1.615 true 2.24,1.906 2.667,2.083 0.427,0.177 10 false GND 1.01,1.906 1.417,2.115 0.406,0.208 10 false IG 0.115,0.031 0.542,0.177 0.427,0.146 10 false *a 0.24,1.469 0.615,1.615 0.375,0.146 10 false G123
*a Rear view of wire harness connector
(to Stabilizer Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G123-22 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G123-24 (IG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE STABILIZER CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)