Home › Vehicle Interior › MIRROR (INT) › INNER REAR VIEW MIRROR › from 2017.08
RM27T0E _58 Vehicle Interior _053734 MIRROR (INT) _0261085 INNER REAR VIEW MIRROR G

MIRROR (INT)  INNER REAR VIEW MIRROR  INSPECTION  


PROCEDURE

Hide 87810 1.REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/o Pre-crash Safety System)

a.

Check operation of the electrochromic inner mirror.

B428635C02
0.781,1.771 0.781,2.313 true 1.469,2.052 1.823,2.052 false 3.417,0.875 3.552,1.354 true 3.542,0.844 3.802,0.656 true 2.844,0.646 3.083,0.813 true 2.906,1.24 3.177,0.885 true 1.875,1.99 2.198,2.271 0.323,0.281 10 false *1 0.698,2.375 1.021,2.656 0.323,0.281 10 false *2 2.177,1.24 2.5,1.521 0.323,0.281 10 false *3 3.792,0.292 4.115,0.573 0.323,0.281 10 false *a 5.115,1.156 5.438,1.438 0.323,0.281 10 false *b 5.146,2.156 5.469,2.438 0.323,0.281 10 false *c 3.573,1.323 3.896,1.604 0.323,0.281 10 false E 3.833,0.521 4.156,0.802 0.323,0.281 10 false IG 2.646,0.5 2.99,0.698 0.344,0.198 10 false EC- 2.719,1.26 3.063,1.458 0.344,0.198 10 false EC+
*1 Black Colored Tape *2 Forward Sensor
*3 Battery - -
*a Component without harness connected (Inner Rear View Mirror Assembly) *b Bright
*c Dark - -


i.

Connect the battery positive (+) lead to terminal 1 (IG) and the negative (-) lead to terminal 2 (E).


ii.

Press the AUTO switch.


iii.

Attach black colored tape to the forward sensor to prevent it from sensing light.


iv.

Shine an electric light on the mirror. Check that the mirror surface changes from bright to dark.

HINT:

When the environment is very bright, the antiglare operation may occur immediately after the tape is applied.



v.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
4 (EC+) - 5 (EC-) Inner rear view mirror surface
Bright → Dark
Below 1 V → 1.25 V


If the result is not as specified, replace the inner rear view mirror assembly.



Hide 87810 2.REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/ Pre-crash Safety System)

a.

Check operation of the electrochromic inner mirror.

E332941C02
0.781,1.917 0.781,2.469 true 1.469,2.167 1.823,2.167 false 3.688,0.948 3.948,0.76 true 2.979,0.729 3.24,0.917 true 2.979,1.281 3.333,1 true 3.552,0.99 3.552,1.333 3.552,1.333 3.969,1.333 true 1.865,2.073 2.188,2.354 0.323,0.281 10 false *1 0.719,2.51 1.042,2.792 0.323,0.281 10 false *2 2.25,1.333 2.573,1.615 0.323,0.281 10 false *3 3.958,0.438 4.281,0.719 0.323,0.281 10 false *a 5.104,1.125 5.427,1.406 0.323,0.281 10 false *b 5.167,2.177 5.49,2.458 0.323,0.281 10 false *c 4.021,1.25 4.344,1.531 0.323,0.281 10 false E 4.01,0.677 4.333,0.958 0.323,0.281 10 false IG 2.708,0.646 3.052,0.844 0.344,0.198 10 false EC- 2.708,1.26 3.052,1.458 0.344,0.198 10 false EC+
*1 Black Colored Tape *2 Forward Sensor
*3 Battery - -
*a Component without harness connected (Inner Rear View Mirror Assembly) *b Bright
*c Dark - -


i.

Connect the battery positive (+) lead to terminal 1 (IG) and the negative (-) lead to terminal 2 (E).


ii.

Press the AUTO switch.


iii.

Attach black colored tape to the forward sensor to prevent it from sensing light.


iv.

Shine an electric light on the mirror. Check that the mirror surface changes from bright to dark.

HINT:

When the environment is very bright, the antiglare operation may occur immediately after the tape is applied.



v.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
4 (EC+) - 5 (EC-) Inner rear view mirror surface
Bright → Dark
Below 1 V → 1.25 V


If the result is not as specified, replace the inner rear view mirror assembly.