Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT ASSEMBLY(for Halogen Headlight) › from 2017.08
RM27T0E _59 Vehicle Exterior _053747 LIGHTING (EXT) _0261276 HEADLIGHT ASSEMBLY(for Halogen Headlight) A

LIGHTING (EXT)  HEADLIGHT ASSEMBLY(for Halogen Headlight)  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 53246B 1.INSTALL HEADLIGHT BRACKET LH

a.

Attach the claw to install the headlight bracket LH.


b.

Install the 3 screws.


Hide 81192 2.INSTALL HEADLIGHT SEAL

a.
E376686C01
0,0 0,0 false
V100155

Area to Clean


Clean the application area as shown in the illustration.

NOTICE:

Remove any remaining double-sided tape, and then clean and degrease the area.



b.

Remove approximately 30 mm (1.18 in.) of the peeling tape from a new headlight seal.


c.
E375669C01
1.667,0.635 2.115,0.958 0.448,0.323 1.438,1.448 1.885,1.771 0.448,0.323 1.448,1.458 1.625,1.656 0.177,0.198 10 true *a 1.677,0.646 1.865,0.844 0.188,0.198 10 true *b
*a Cutout
*b Protrusion


Align the cutout of the headlight seal with the protrusion and set it.


d.
E376687C01
0,0 0,0 false
V100145

Peeling Tape


While peeling the peeling tape, align the headlight seal to the curve and set it.


e.
E375670

Press the set portion of the part with your finger to secure it.

NOTICE:

Do not slide your finger horizontally, as doing so may stretch the part unnecessarily.



Hide 52134I 3.INSTALL FRONT BUMPER BAR REINFORCEMENT LH

a.

Install the front bumper bar reinforcement LH with the 2 screws.


Hide 81125 4.INSTALL HEADLIGHT CORD

E379776C01
1.083,2.448 1.396,2.604 0.313,0.156 10 false *a
*a Hook


a.

Attach the hook.


b.

Install the headlight cord with the 2 screws.


c.

Attach the 6 wire harness clamps.


Hide 85669 5.INSTALL HEADLIGHT LEVELING MOTOR BASE PACKING (w/ Headlight Leveling)

a.

Install a new headlight leveling motor base packing.


Hide 85662 6.INSTALL HEADLIGHT LEVELING MOTOR LH (w/ Headlight Leveling)

a.

Set the tip of the aiming screw of the headlight leveling motor LH.


b.
E375668C01
1.208,1.896 1.771,1.01 true 1.094,1.906 1.406,2.063 0.313,0.156 10 false *a
*a Aiming Screw


Tighten the aiming screw of the headlight leveling motor LH the same number of rotations recorded when removing it to connect the headlight leveling motor LH.


c.

Insert the headlight leveling motor LH.


d.

Turn the headlight leveling motor LH clockwise to install it.

HINT:

For the headlight assembly RH, turn the headlight leveling motor RH counterclockwise to install it.



e.

Tighten the aiming screw 20 rotations.


f.

Connect the connector.


Hide 81510C 7.INSTALL FRONT TURN SIGNAL LIGHT BULB

a.

Install the front turn signal light bulb to the front turn signal light bulb socket.


b.
E375651C01
1.698,1.719 1.51,0.938 true 1.75,0.594 1.438,0.875 true 2.115,3.292 1.667,3.365 true 1.635,1.729 1.948,1.885 0.313,0.156 10 false *a 1.792,0.469 2.104,0.625 0.313,0.156 10 false *b 2.167,3.198 2.479,3.354 0.313,0.156 10 false *c
*a Matchmark
*b Unlock Position Mark
*c Lock Position Mark


Align the matchmark of the front turn signal light bulb socket with the unlock position mark, and then rotate the front turn signal light bulb socket clockwise until the lock position mark to install the front turn signal light bulb socket.


Hide 81610F 8.INSTALL CLEARANCE LIGHT BULB

a.

Install the clearance light bulb to the clearance light bulb socket.


b.
E375653C01
1.865,1.021 2.24,1.406 true 1.927,0.958 2.25,0.958 true 2,3.771 2.229,4.094 true 2.25,1.448 2.563,1.604 0.313,0.156 10 false *a 2.302,0.875 2.615,1.031 0.313,0.156 10 false *b 2.219,4.146 2.531,4.302 0.313,0.156 10 false *c
*a Matchmark
*b Unlock Position Mark
*c Lock Position Mark


Align the matchmark of the clearance light bulb socket with the unlock position mark, and then rotate the clearance light bulb socket clockwise until the lock position mark to install the clearance light bulb socket.


Hide 81110D 9.INSTALL NO. 2 HEADLIGHT BULB

a.

Insert the No. 2 headlight bulb.

NOTICE:

Do not touch the glass part of the No. 2 headlight bulb.



b.
E375662

Turn the No. 2 headlight bulb clockwise until the bulb stops to install it.


c.

Connect the connector.


Hide 81110B 10.INSTALL NO. 1 HEADLIGHT BULB

a.

Insert the No. 1 headlight bulb.

NOTICE:

Do not touch the glass part of the No. 1 headlight bulb.



b.
E375660

Turn the No. 1 headlight bulb clockwise until the bulb stops to install it.


c.

Connect the connector.